104740-8750 ZEXEL 9 460 610 643 BOSCH INJECTION-PUMP ASSEMBLY 9460610643 1047408750 md301925

Information Cross number Calibration Data Calibration Data Ex

Information injection-pump assembly

BOSCH 9 460 610 643 9460610643

ZEXEL 104740-8750 1047408750

MITSUBISHI MD301925 md301925

Price: query

Buy now
Add to cart Go to cart

Rating:

Buy INJECTION-PUMP ASSEMBLY 104740-8750 zexel genuine, new aftermarket engine parts with delivery

Components :

0.	INJECTION-PUMP ASSEMBLY	104740-8750
1.	_
2.	FUEL INJECTION PUMP	104640-8750
3.	NUMBER PLATE	146954-4200
4.	_	479771-0520
5.	CAPSULE
6.	ADJUSTING DEVICE
7.	NOZZLE AND HOLDER ASSY	105148-1311
8.	Nozzle and Holder	MD196607
9.	Open Pre:MPa(Kqf/cm2)	14.7{150}
10.	NOZZLE-HOLDER	105078-0181
11.	NOZZLE	105007-1300

Scheme ###:

1/6.	[1]	146601-0700	PACKING RING
6.	[1]	146100-0220	SUPPLY PUMP
9.	[1]	146103-0100	COVER
10.	[2]	139104-0000	FLAT-HEAD SCREW
12.	[1]	146200-0320	DRIVE SHAFT
12/1.	[1]	146200-0300	DRIVE SHAFT
12/2.	[1]	146201-0000	WOODRUFF KEY
12/3.	[2]	146202-0100	DAMPER
12/4.	[1]	146203-0000	TOOTHED GEAR
17.	[1]	146204-0000	PLAIN WASHER
20.	[1]	146210-3520	ROLLER SET
24.	[1]	146303-0100	BEARING PIN
25.	[1]	146304-0000	BEARING PIN
26.	[1]	146305-0000	CLAMPING BAND
27.	[1]	146205-0000	SLOTTED WASHER
29.	[1]	146220-2120	CAM PLATE
30.	[1]	146600-0800	O-RING
31.	[1]	146311-6320	PUMP PLUNGER
32.	[1]	146301-0000	SLIDING PIECE
34.	[1]	146312-2900	COMPRESSION SPRING
34B.	[1]	146312-2800	COMPRESSION SPRING
34C.	[1]	146312-3200	COMPRESSION SPRING
35/1.	[1]	146690-3200	SHIM D11.5&9.4T0.1
35/1.	[1]	146690-3300	SHIM D11.5&9.4T0.2
35/1.	[1]	146690-3400	SHIM D11.5&9.4T0.25
35/1.	[1]	146690-3500	SHIM D11.5&9.4T1.0
35/1.	[1]	146690-4100	SHIM D11.5&9.4T2
35/1.	[1]	146690-4200	SHIM D11.5&9.4T0.5
35/1.	[1]	146690-4300	SHIM D11.5&9.4T0.75
36.	[1]	146600-0800	O-RING
37.	[1]	146310-4020	COVER
38.	[2]	146620-5000	BLEEDER SCREW
39.	[1]	146310-0100	COVER
40.	[2]	146620-5000	BLEEDER SCREW
41.	[1]	146312-1900	COMPRESSION SPRING
43.	[1]	146230-0000	SHIM
44.	[1]	146230-0100	PLAIN WASHER
45.	[1]	146231-0001	SLOTTED WASHER
47.	[2]	146233-0000	SLOTTED WASHER
48/1.	[1]	146603-0100	SHIM D17.0&5.2T0.80
48/1.	[1]	146603-0200	SHIM D17.0&5.2T1.00
48/1.	[1]	146603-0300	SHIM D17.0&5.2T1.20
48/1.	[1]	146603-0400	SHIM D17.0&5.2T1.50
48/1.	[1]	146690-1400	SHIM D17&5.2T0.9
48/1.	[1]	146690-1500	SHIM D17&5.2T1.1
48/1.	[1]	146690-1600	SHIM D17&5.2T1.3
48/1.	[1]	146690-1700	SHIM D17&5.2T1.4
48/1.	[1]	146690-1800	SHIM D17&5.2T1.6
49.	[2]	146234-0500	GUIDE PIN
50.	[1]	146401-3220	HYDRAULIC HEAD
50.	[1]	146401-3220	HYDRAULIC HEAD
50.	[1]	146401-3220	HYDRAULIC HEAD
51.	[1]	146600-0000	O-RING
52/1.	[1]	146420-0200	SHIM D9.5&3.0T1.94
52/1.	[1]	146420-0700	SHIM D9.5&3.0T2.04
52/1.	[1]	146420-1200	SHIM D9.5&3.0T2.14
52/1.	[1]	146420-1700	SHIM D9.5&3.0T2.24
52/1.	[1]	146420-2200	SHIM D9.5&3.0T2.34
52/1.	[1]	146420-2700	SHIM D9.5&3.0T2.44
52/1.	[1]	146420-3200	SHIM D9.5&3.0T2.54
52/1.	[1]	146420-3700	SHIM D9.5&3.0T2.64
52/1.	[1]	146420-5600	SHIM D9.5&3.0T1.84
54.	[4]	146433-0100	GASKET
55.	[4]	146430-2020	DELIVERY-VALVE ASSEMBLY VE20
56.	[4]	146432-0000	COMPRESSION SPRING
58.	[4]	146440-0320	FITTING
60.	[3]	139106-0100	FLAT-HEAD SCREW
66.	[1]	146600-0100	O-RING
67.	[1]	146703-2320	COMPENSATOR,MANIFOLD-PRES
67/1.	[1]	146805-7120	GOVERNOR COVER
67/14.	[1]	146621-1700	UNION NUT
67/16.	[1]	146526-3000	BLEEDER SCREW
67/23.	[1]	146925-7520	BRACKET
67/24.	[2]	010206-2240	HEX-SOCKET-HEAD CAP SCREW
67/31.	[1]	146710-0700	BUSHING
67/32.	[1]	146711-0000	PLATE
67/33.	[1]	139218-0400	UNION NUT
67/34.	[1]	146712-0700	BEARING PIN
67/35.	[1]	146621-0300	UNION NUT
67/36.	[1]	146600-1400	O-RING
67/37.	[1]	146710-0100	BUSHING
67/38.	[1]	139506-0200	GASKET
67/39.	[1]	146620-0300	CAPSULE
67/40.	[1]	026512-1540	GASKET
67/41.	[1]	146713-4300	ADJUSTING PIN
67/42.	[2]	146714-0200	PLATE
67/43.	[1]	146715-0300	DIAPHRAGM
67/44.	[1]	139306-0100	LOCKING WASHER
67/45.	[1]	013030-6040	UNION NUT
67/46.	[1]	146716-0000	UNION NUT
67/47.	[1]	146717-2900	COILED SPRING
67/48/1.	[1]	146720-3900	SPACER BUSHING L5.5
67/48/1.	[1]	146720-4000	SPACER BUSHING L5.7
67/48/1.	[1]	146720-4100	SPACER BUSHING L5.9
67/48/1.	[1]	146720-4200	SPACER BUSHING L6.1
67/48/1.	[1]	146720-4300	SPACER BUSHING L6.3
67/48/1.	[1]	146720-4400	SPACER BUSHING L6.5
67/48/1.	[1]	146720-8900	SPACER BUSHING L6.7
67/48/1.	[1]	146725-0900	SPACER BUSHING L5.6
67/48/1.	[1]	146725-1000	SPACER BUSHING L5.8
67/48/1.	[1]	146725-1100	SPACER BUSHING L6.0
67/48/1.	[1]	146725-1200	SPACER BUSHING L6.2
67/48/1.	[1]	146725-1300	SPACER BUSHING L6.4
67/48/1.	[1]	146725-1400	SPACER BUSHING L6.6
67/49.	[1]	146721-3720	COVER
67/50.	[1]	146722-0200	FLAT-HEAD SCREW
67/51.	[1]	146600-0300	O-RING
67/53.	[1]	013020-6040	UNION NUT
67/54.	[2]	139006-4600	BLEEDER SCREW
67/54.	[2]	139006-4600	BLEEDER SCREW
67/55.	[2]	139006-4800	BLEEDER SCREW
67/56.	[1]	146723-0300	CONTROL LEVER
67/57.	[1]	146712-0100	BEARING PIN
67/58.	[2]	146620-0600	CAPSULE
67/59.	[2]	026506-1040	GASKET
67/60.	[1]	146724-0300	ELEMENT
67/61.	[1]	146724-0600	CAPSULE
67/64.	[1]	146926-7200	BRACKET
67/78.	[1]	146600-4400	SEAL RING
67/96.	[1]	146659-7220	CLAMPING BAND
67/98.	[2]	146648-2800	SPACER BUSHING
67/99.	[1]	014110-6440	LOCKING WASHER D12.2&6.1T1.5
67/100.	[1]	013020-6040	UNION NUT
67/102.	[1]	146926-5520	BRACKET
67/200.	[1]	139308-0300	PLAIN WASHER
67/201.	[1]	146545-3400	THREADED PIN L53.00
67/201B.	[1]	146545-3500	THREADED PIN L55.00
67/201C.	[1]	146545-3600	THREADED PIN L57.00
67/202.	[1]	139208-0900	UNION NUT
67/203.	[1]	146600-1200	O-RING
68.	[1]	146514-1220	CONTROL SHAFT
69.	[1]	139310-0200	PLAIN WASHER
72.	[1]	146830-7120	CONTROL LEVER STAMP 071
72B.	[1]	146830-7220	CONTROL LEVER STAMP 072
73.	[1]	014110-6440	LOCKING WASHER D12.2&6.1T1.5
75.	[1]	013020-6040	UNION NUT
95.	[1]	146551-9320	FULCRUM LEVER
104.	[2]	146568-0000	SLOTTED SPRING PIN
105.	[2]	026508-1140	GASKET D11.4&8.2T1.0
106.	[2]	146588-0500	COILED SPRING
107.	[1]	146569-0300	UNION NUT
108.	[1]	146570-0420	GOVERNOR SHAFT
109.	[1]	146600-0400	O-RING
110/1.	[1]	146571-0000	SHIM D20.2&8.3T1.05
110/1.	[1]	146571-0100	SHIM D20.2&8.3T1.25
110/1.	[1]	146571-0200	SHIM D20.2&8.3T1.45
110/1.	[1]	146571-0300	SHIM D20.2&8.3T1.65
110/1.	[1]	146571-0400	SHIM D20.2&8.3T1.85
111.	[1]	146602-0600	PLAIN WASHER
112.	[1]	146572-0020	FLYWEIGHT ASSEMBLY
114.	[1]	146602-0500	PLAIN WASHER
115.	[1]	146975-8100	SLIDING SLEEVE
116.	[1]	146576-0000	SEALING CAP
117/1.	[1]	146577-2200	PLUG L2.90
117/1.	[1]	146577-2300	PLUG L3.10
117/1.	[1]	146577-2400	PLUG L3.30
117/1.	[1]	146577-2500	PLUG L3.50
117/1.	[1]	146577-2600	PLUG L3.70
117/1.	[1]	146577-2700	PLUG L3.90
117/1.	[1]	146577-2800	PLUG L4.10
117/1.	[1]	146577-2900	PLUG L4.30
117/1.	[1]	146577-3000	PLUG L4.50
117/1.	[1]	146577-7100	PLUG L3.0
117/1.	[1]	146577-7200	PLUG L3.2
117/1.	[1]	146577-7300	PLUG L3.4
117/1.	[1]	146577-7400	PLUG L3.6
117/1.	[1]	146577-7500	PLUG L3.8
117/1.	[1]	146577-7600	PLUG L4.0
117/1.	[1]	146577-7700	PLUG L4.2
117/1.	[1]	146577-7800	PLUG L4.4
123.	[4]	146620-0500	HEX-SOCKET-HEAD CAP SCREW
130.	[1]	146421-0020	CAPSULE
130/2.	[1]	026508-1140	GASKET D11.4&8.2T1.0
130/3.	[1]	146422-0000	BLEEDER SCREW
130/4.	[1]	146600-0500	O-RING
133.	[1]	146600-0600	O-RING
134.	[1]	146600-0700	O-RING
135.	[1]	146110-0220	CONTROL VALVE STAMP 02
135/5.	[1]	146114-0000	SPRING WASHER
136.	[1]	146120-0020	OVER FLOW VALVE
137.	[2]	139512-0500	GASKET
138.	[1]	146665-4520	INLET UNION
200.	[1]	146206-0100	COILED SPRING
205.	[1]	029470-4030	WOODRUFF KEY
217.	[1]	146542-5300	SLOTTED WASHER
218.	[1]	146592-2500	COILED SPRING
219.	[1]	146541-3000	BUSHING
220.	[1]	146592-2600	COILED SPRING
224.	[1]	139006-4400	BLEEDER SCREW
230.	[1]	146613-2500	BRACKET
231.	[1]	139006-4400	BLEEDER SCREW
232.	[1]	146931-3200	BRACKET STAMP 132
233.	[1]	146658-9020	WIRE
234.	[1]	139006-4800	BLEEDER SCREW
235.	[1]	146659-0600	CLAMPING BAND
237.	[1]	146620-0200	HEX-SOCKET-HEAD CAP SCREW
240.	[1]	146650-1220	PULLING ELECTROMAGNET
240/8.	[1]	146600-1700	O-RING
243.	[1]	146621-1000	UNION NUT
245.	[3]	139512-0500	GASKET
246.	[1]	139812-1900	EYE BOLT
247.	[1]	146666-5520	INLET UNION
248.	[1]	146614-0200	SPACER BUSHING
251.	[1]	146125-0101	FILTER
252.	[1]	146125-0200	COILED SPRING
275.	[1]	146612-4800	BRACKET
276.	[2]	010010-1640	BLEEDER SCREW
280.	[1]	146361-7020	START ADVANCE ASSY STAMP 119
281.	[1]	146600-0800	O-RING
282.	[2]	010206-1240	HEX-SOCKET-HEAD CAP SCREW
286.	[1]	020106-3540	BLEEDER SCREW
287.	[1]	014010-6140	PLAIN WASHER D13&6.5T1.0
288.	[1]	146931-6300	BRACKET
310.	[1]	146685-7120	POTENTCIOMETER
310/2.	[2]	139104-0400	FLAT-HEAD SCREW
310/3.	[1]	146648-2900	JOINT CONNECTION
310/3B.	[1]	146648-3000	JOINT CONNECTION
310/3C.	[1]	146648-3100	JOINT CONNECTION
310/3D.	[1]	146648-3200	JOINT CONNECTION
310/3E.	[1]	146648-3300	JOINT CONNECTION
310/3F.	[1]	146648-4700	JOINT CONNECTION
310/3G.	[1]	146648-5300	JOINT CONNECTION
310/3H.	[1]	146649-1700	JOINT CONNECTION
310/4.	[1]	146661-0601	BOOT
312.	[1]	146933-6000	BRACKET
313.	[1]	020106-1240	BLEEDER SCREW
800S.	[1]	146018-4820	PUMP HOUSING
800S/1/6.	[1]	146601-0700	PACKING RING
804S.	[1]	146232-0320	COMPRESSION SPRING
805S.	[1]	146574-0120	PARTS SET
810S.	[1]	146600-1120	REPAIR SET
821S.	[1]	146210-5720	ROLLER SET
835S.	[1]	146598-1000	CAP
836S/1.	[1]	146598-0600	CAP L18
836S/1.	[1]	146598-0700	CAP L21
836S/1.	[1]	146598-0800	CAP L24
836S/1.	[1]	146598-0900	CAP L27
903.	[1]	479771-0520	PULSE GENERATOR
906.	[1]	146954-4200	NAMEPLATE
910S.	[1]	146600-4220	PARTS SET
910S.	[1]	146600-4220	PARTS SET
911S.	[1]	479771-0520	PULSE GENERATOR
912S.	[1]	026508-1140	GASKET D11.4&8.2T1.0
913S.	[1]	146422-0000	BLEEDER SCREW
914S.	[1]	146699-0020	VALVE SET
914S.	[1]	146699-0020	VALVE SET
914S.	[1]	146699-0020	VALVE SET
915S.	[1]	146658-9020	WIRE
916S.	[1]	025804-1610	WOODRUFF KEY
917S.	[1]	146685-7110	POTENTCIOMETER

Include in #2:

104740-8750 as INJECTION-PUMP ASSEMBLY

Cross reference number

BOSCH 9 460 610 643 9460610643

ZEXEL 104740-8750 1047408750

MITSUBISHI MD301925 md301925

Zexel num

Bosch num

Firm num

Name

104740-8750

9 460 610 643

MD301925 MITSUBISHI

INJECTION-PUMP ASSEMBLY
4D56 K 11CJ INJECTION PUMP ASSY VE4 VE

Calibration Data:

Adjustment conditions

Test oil
1404 Test oil ISO4113orSAEJ967d

Test oil temperature degC 45 45 50

Nozzle 105780-0060

Bosch type code NP-DN0SD1510

Nozzle holder 105780-2150

Opening pressure MPa 13 13 13.3

Opening pressure kgf/cm2 133 133 136

Injection pipe 157805-7320

Injection pipe
Inside diameter - outside diameter - length (mm) mm 2-6-450

Joint assembly 157641-4720

Tube assembly 157641-4020

Transfer pump pressure kPa 20 20 20

Transfer pump pressure kgf/cm2 0.2 0.2 0.2

Direction of rotation (viewed from drive side)
Right R

Injection timing adjustment

Pump speed r/min 1250 1250 1250

Boost pressure kPa 73.3 72 74.6

Boost pressure mmHg 550 540 560

Average injection quantity mm3/st. 74.6 74.1 75.1

Difference in delivery mm3/st. 6

Basic *

Remarks
Full

Injection timing adjustment_02

Pump speed r/min 750 750 750

Boost pressure kPa 44 42.7 45.3

Boost pressure mmHg 330 320 340

Average injection quantity mm3/st. 60.6 60.1 61.1

Difference in delivery mm3/st. 5

Basic *

Remarks
CBS

Injection timing adjustment_03

Pump speed r/min 750 750 750

Boost pressure kPa 0 0 0

Boost pressure mmHg 0 0 0

Average injection quantity mm3/st. 50.6 50.1 51.1

Difference in delivery mm3/st. 4

Basic *

Remarks
NA

Injection timing adjustment_04

Pump speed r/min 2650 2650 2650

Boost pressure kPa 73.3 72 74.6

Boost pressure mmHg 550 540 560

Average injection quantity mm3/st. 27.9 24.4 31.4

Injection timing adjustment_05

Pump speed r/min 2100 2100 2100

Boost pressure kPa 73.3 72 74.6

Boost pressure mmHg 550 540 560

Average injection quantity mm3/st. 62.5 60 65

Injection timing adjustment_06

Pump speed r/min 1250 1250 1250

Boost pressure kPa 73.3 72 74.6

Boost pressure mmHg 550 540 560

Average injection quantity mm3/st. 74.6 73.6 75.6

Remarks
Full

Injection timing adjustment_07

Pump speed r/min 1000 1000 1000

Boost pressure kPa 73.3 72 74.6

Boost pressure mmHg 550 540 560

Average injection quantity mm3/st. 74 71.5 76.5

Injection timing adjustment_08

Pump speed r/min 750 750 750

Boost pressure kPa 44 42.7 45.3

Boost pressure mmHg 330 320 340

Average injection quantity mm3/st. 60.6 59.6 61.6

Remarks
CBS

Injection timing adjustment_09

Pump speed r/min 750 750 750

Boost pressure kPa 0 0 0

Boost pressure mmHg 0 0 0

Average injection quantity mm3/st. 50.6 49.6 51.6

Remarks
NA

Injection quantity adjustment

Pump speed r/min 2650 2650 2650

Boost pressure kPa 73.3 72 74.6

Boost pressure mmHg 550 540 560

Average injection quantity mm3/st. 27.9 24.9 30.9

Difference in delivery mm3/st. 8.5

Basic *

Injection quantity adjustment_02

Pump speed r/min 2950 2950 2950

Boost pressure kPa 73.3 72 74.6

Boost pressure mmHg 550 540 560

Average injection quantity mm3/st. 5

Governor adjustment

Pump speed r/min 375 375 375

Boost pressure kPa 0 0 0

Boost pressure mmHg 0 0 0

Average injection quantity mm3/st. 19.4 17.9 20.9

Difference in delivery mm3/st. 2

Basic *

Governor adjustment_02

Pump speed r/min 900 900 900

Boost pressure kPa 0 0 0

Boost pressure mmHg 0 0 0

Average injection quantity mm3/st. 5

Governor adjustment_03

Pump speed r/min 750 750 750

Boost pressure kPa 0 0 0

Boost pressure mmHg 0 0 0

Average injection quantity mm3/st. 8

Governor adjustment_04

Pump speed r/min 375 375 375

Boost pressure kPa 0 0 0

Boost pressure mmHg 0 0 0

Average injection quantity mm3/st. 19.4 17.4 21.4

Timer adjustment

Pump speed r/min 100 100 100

Boost pressure kPa 0 0 0

Boost pressure mmHg 0 0 0

Average injection quantity mm3/st. 75 55 95

Basic *

Remarks
IDLE

Speed control lever angle

Pump speed r/min 375 375 375

Boost pressure kPa 0 0 0

Boost pressure mmHg 0 0 0

Average injection quantity mm3/st. 0 0 0

0000000901

Pump speed r/min 1250 1250 1250

Boost pressure kPa 73.3 72 74.6

Boost pressure mmHg 550 540 560

Overflow quantity cm3/min 420 288 552

Stop lever angle

Pump speed r/min 1250 1250 1250

Boost pressure kPa 73.3 72 74.6

Boost pressure mmHg 550 540 560

Pressure kPa 549 520 578

Pressure kgf/cm2 5.6 5.3 5.9

Basic *

Stop lever angle_02

Pump speed r/min 1250 1250 1250

Boost pressure kPa 73.3 72 74.6

Boost pressure mmHg 550 540 560

Pressure kPa 549 520 578

Pressure kgf/cm2 5.6 5.3 5.9

Stop lever angle_03

Pump speed r/min 1500 1500 1500

Boost pressure kPa 73.3 72 74.6

Boost pressure mmHg 550 540 560

Pressure kPa 608 579 637

Pressure kgf/cm2 6.2 5.9 6.5

Stop lever angle_04

Pump speed r/min 2100 2100 2100

Boost pressure kPa 73.3 72 74.6

Boost pressure mmHg 550 540 560

Pressure kPa 736 707 765

Pressure kgf/cm2 7.5 7.2 7.8

0000001101

Pump speed r/min 1250 1250 1250

Boost pressure kPa 73.3 72 74.6

Boost pressure mmHg 550 540 560

Timer stroke mm 4.6 4.4 4.8

Basic *

_02

Pump speed r/min 500 500 500

Boost pressure kPa 73.3 72 74.6

Boost pressure mmHg 550 540 560

Timer stroke mm 1.2 0.5 1.9

_03

Pump speed r/min 1000 1000 1000

Boost pressure kPa 73.3 72 74.6

Boost pressure mmHg 550 540 560

Timer stroke mm 3.5 2.9 4.1

_04

Pump speed r/min 1250 1250 1250

Boost pressure kPa 73.3 72 74.6

Boost pressure mmHg 550 540 560

Timer stroke mm 4.6 4.3 4.9

_05

Pump speed r/min 1500 1500 1500

Boost pressure kPa 73.3 72 74.6

Boost pressure mmHg 550 540 560

Timer stroke mm 5.6 5 6.2

_06

Pump speed r/min 2000 2000 2000

Boost pressure kPa 73.3 72 74.6

Boost pressure mmHg 550 540 560

Timer stroke mm 7.5 6.9 8.1

_07

Pump speed r/min 2100 2100 2100

Boost pressure kPa 73.3 72 74.6

Boost pressure mmHg 550 540 560

Timer stroke mm 7.7 7.2 8.2

0000001201

Max. applied voltage V 8 8 8

Test voltage V 13 12 14

0000001401

Pump speed r/min 1250 1250 1250

Boost pressure kPa 73.3 72 74.6

Boost pressure mmHg 550 540 560

Average injection quantity mm3/st. 56.9 56.4 57.4

Timer stroke variation dT mm 0.7 0.7 0.7

Basic *

_02

Pump speed r/min 1250 1250 1250

Boost pressure kPa 73.3 72 74.6

Boost pressure mmHg 550 540 560

Average injection quantity mm3/st. 56.9 55.9 57.9

Timer stroke variation dT mm 0.4 0.4 0.4

_03

Pump speed r/min 1250 1250 1250

Boost pressure kPa 73.3 72 74.6

Boost pressure mmHg 550 540 560

Average injection quantity mm3/st. 43 41.5 44.5

Timer stroke variation dT mm 2.1 2.1 2.1

Timing setting

K dimension mm 3.3 3.2 3.4

KF dimension mm 5.8 5.7 5.9

MS dimension mm 1.2 1.1 1.3

BCS stroke mm 5.7 5.5 5.9

Control lever angle alpha deg. 59 55 63

Control lever angle beta deg. 42 37 47

Test data Ex:

0000001801 POTENTIOMETER ADJUSTMENT

C:Position of the control lever N:Pump speed (r/min) V:Output voltage (V) Q:Injection quantity (mm3/st) A:Adjusting point B:Checking point C1:Idling C2:Full speed Vi:Applied voltage input
----------

----------
V1=1.8+-0.03V V2=(8.81+-1.1)V Vi=10V

0000001901 W-CSD ADJUSTMENT

Adjustment of the W-CSD 1. Adjustment of the advance angle of the timer (1)Determine the timer advance angle using the following graph. (2)(1) Adjust with the screw (A) so that the timer advance angle determined in the item (1) is obtained. X:Temperature t (deg C) Y:Timer stroke TA (mm) (B): Timer stroke TA (mm):
----------

----------
(C)=TA=-0.0376t+1.38(-20<=t(degC))

0000002001 W-FICD LEVER ADJUSTMENT

2. W-FICD (E) adjustment (1)Insert a block gauge L determined from the graph below between the control lever (D) and the idling stopper bolt (C). (2)Insert a shim L1 between the W-FICD lever (E) and the control lever (F). Adjust the W-FICD lever (E) so that it contacts the control lever (F) and fix it using bolt (B). TT Caution: a) The temperature of the wax at adjustment must not exceed a. b) After completion of the adjustment, confirm that allowance for adjustment of the screw (G) is at least L2. t = temperature (deg C) H = control lever position L (mm)
----------
L=L+-0.05mm L1=3+-0.05mm L2=3mm a=30degC T=3.4~4.9Nm{0.35~0.5kgfm}
----------
L=L+-0.05mm L1=3+-0.05mm L2=3++mm L=-0.177t+6.05(-20<=t(degC))(L1=3+-0.05)

Information:

(1) Torque for bolt that holds the impeller ... 39 3 N m (28 2 lb ft)(2) Shaft diameter at carbon seal assembly seat area must be ... 19.10 0.05 mm (.752 .002 in) Use 4C9500 Quick Cure Primer to clean the water pump shaft and the ceramic ring seal counterbore in the pump housing.(3) Ring and water seal. Use a 125-9622 Seal Installation Tool and hand pressure to install the rubber seal and ceramic ring as a unit in the pump housing bore. Make sure the identification mark (holes or groove) on the ceramic ring face is installed inside the rubber seal.(4) Seal assembly. a. Remove the spring from the seal.b. Put clean water on the seal assembly as the only lubrication for assembly. Do not get any grease or oil on the seal faces.c. Do not stretch the rubber of the seal assembly at installation. If the seal is stretched, the service life is shortened.d. Use a 125-9622 Seal Installation Tool and hand pressure to install the seal assembly on the pump shaft until the carbon face makes light contact with the smooth face of the ceramic ring. The carbon seal assembly must rotate with the water pump shaft. Do not use any lubricant (except clean water) that will reduce the friction between the seal and the shaft.e. Install the carbon seal assembly spring.(5) Oil seal. Put a small amount of clean engine oil on the lip of the seal at assembly. Install it with the lip toward the bearings as shown.(6) Torque for bolt that holds the gear ... 215 40 N m (160 30 lb ft)Water Pump (135-4925 and 135-4926)
(1) With flat side towards housing install oil seal flush with housing using a suitable driver. DO NOT lubricate lip of seal.(2) Install Shaft. Shaft diameter at unitized seal assembly must be ... 19.10 .01 mm (.752 .0004 in). Using a 138-9299 Installation Tool over the shaft with the chamfer facing out, carefully insert the shaft into the oil seal. Position the shaft to center the oil seal lips on the shaft running surface. Then remove installation tool from shaft.(3) Install bearings. Slide the bearing assembly over the shaft and into the housing. Torque the bearing retainer plate bolts to ... 25 6 N m (19 4 lb ft)(4) Torque for gear retaining bolt ... 215 40 N m (158 30 lb ft)(5) Unitized seal. Using a 139-0088 Installation Tool and a suitable press to install the seal onto the pump shaft and into the housing bore, insure that the seal is fully seated in the housing bore. DO NOT use a hammer to install the seal as damage to ceramic sealing face will occur.(6) Bolt torque for the impeller retaining bolts is ... 39 3 N m (28 2 lb ft)