101402-8080 ZEXEL 9 400 613 986 BOSCH INJECTION-PUMP ASSEMBLY 9400613986 1014028080 8973258420

Information Cross number Calibration Data Calibration Data Ex

Information injection-pump assembly

BOSCH 9 400 613 986 9400613986

ZEXEL 101402-8080 1014028080

ISUZU 8973258420 8973258420

Price: query

Buy now
Add to cart Go to cart

Rating:

Buy INJECTION-PUMP ASSEMBLY 101402-8080 zexel genuine, new aftermarket engine parts with delivery

Service parts 101402-8080 INJECTION-PUMP ASSEMBLY:

1. _

2. FUEL INJECTION PUMP 101040-4070

3. GOVERNOR 105411-2510

4. SUPPLY PUMP 105220-7560

5. AUTOM. ADVANCE MECHANIS

6. COUPLING PLATE

7. COUPLING PLATE 156643-4120

8. _

9. _

10. NOZZLE AND HOLDER ASSY 105160-5120

11. Nozzle and Holder 1-15300-394-0

12. Open Pre:MPa(Kqf/cm2)

13. NOZZLE-HOLDER 105030-4750

14. NOZZLE 105025-3030

15. NOZZLE SET

Include in #1:

101402-8080 as INJECTION-PUMP ASSEMBLY

106684-4490 as _

Cross reference number

BOSCH 9 400 613 986 9400613986

ZEXEL 101402-8080 1014028080

ISUZU 8973258420 8973258420

Zexel num

Bosch num

Firm num

Name

101402-8080

9 400 613 986

8973258420 ISUZU

INJECTION-PUMP ASSEMBLY
4BG1-T K

Calibration Data:

Adjustment conditions

Test oil
1404 Test oil ISO4113 or {SAEJ967d}

Test oil temperature degC 40 40 45

Nozzle and nozzle holder 105780-8140

Bosch type code EF8511/9A

Nozzle 105780-0000

Bosch type code DN12SD12T

Nozzle holder 105780-2080

Bosch type code EF8511/9

Opening pressure MPa 17.2

Opening pressure kgf/cm2 175

Injection pipe
Outer diameter - inner diameter - length (mm) mm 6-2-600

Overflow valve 134424-4120

Overflow valve opening pressure kPa 255 255 255

Overflow valve opening pressure kgf/cm2 2.6 2.6 2.6

Tester oil delivery pressure kPa 255 255 255

Tester oil delivery pressure kgf/cm2 2.6 2.6 2.6

Direction of rotation (viewed from drive side)
Right R

Injection timing adjustment

Direction of rotation (viewed from drive side)
Right R

Injection order 1-3-4-2

Pre-stroke mm 4.2 4.15 4.25

Beginning of injection position
Drive side NO.1

Difference between angles 1
Cal 1-3 deg. 90 89.5 90.5

Difference between angles 2
Cal 1-4 deg. 180 179.5 180.5

Difference between angles 3
Cyl.1-2 deg. 270 269.5 270.5

Injection quantity adjustment

Adjusting point A

Rack position 10

Pump speed r/min 1100 1100 1100

Average injection quantity mm3/st. 85.5 84.4 86.6

Max. variation between cylinders % 0 -2 2

Basic *

Fixing the lever *

Boost pressure kPa 93.3 93.3

Boost pressure mmHg 700 700

Injection quantity adjustment_02

Adjusting point -

Rack position 7.7+-0.5

Pump speed r/min 475 475 475

Average injection quantity mm3/st. 8.8 7.4 10.2

Max. variation between cylinders % 0 -14 14

Fixing the rack *

Boost pressure kPa 0 0 0

Boost pressure mmHg 0 0 0

Remarks
Adjust only variation between cylinders; adjust governor according to governor specifications.

Injection quantity adjustment_03

Adjusting point E

Rack position 10.9++

Pump speed r/min 100 100 100

Average injection quantity mm3/st. 80 75 85

Fixing the lever *

Boost pressure kPa 0 0 0

Boost pressure mmHg 0 0 0

Rack limit *

Boost compensator adjustment

Pump speed r/min 650 650 650

Rack position 8.7

Boost pressure kPa 40 36 44

Boost pressure mmHg 300 270 330

Boost compensator adjustment_02

Pump speed r/min 650 650 650

Rack position 9

Boost pressure kPa 80 73.3 86.7

Boost pressure mmHg 600 550 650

Test data Ex:

Governor adjustment

N:Pump speed R:Rack position (mm) (1)Target notch: K (2)Tolerance for racks not indicated: +-0.05mm. (3)RACK LIMIT (4)Boost compensator stroke: BCL (5)Rack difference between N = N1 and N = N2 (6)Main spring setting (7)Set idle sub-spring
----------
K=9 BCL=0.3+-0.1mm N1=1100r/min N2=650r/min
----------

Speed control lever angle

F:Full speed I:Idle (1)Stopper bolt setting
----------

----------
a=3deg+-5deg b=20deg+-5deg

Stop lever angle

N:Pump normal S:Stop the pump. (1)Pump speed aa and rack position bb (to be sealed at delivery) (2)Normal
----------
aa=0r/min bb=1-0.5mm
----------
a=32deg+-5deg b=(55deg)

0000001501 TAMPER PROOF

Tamperproofing-equipped boost compensator cover installation procedure (A): After adjusting the boost compensator, assemble then tighten the bolts to remove the heads. (B): Specified torque (1)Before adjusting the governor and the boost compensator, tighten the screw to the specified torque. (Tightening torque T = T1 maximum) (2)After adjusting the governor and the boost compensator, tighten to the specified torque to break off the bolt heads. (Tightening torque T = T2)
----------
T1=2.5N-m(0.25kgf-m) T2=2.9~4.4N-m(0.3~0.45kgf-m)
----------

Timing setting

(1)Pump vertical direction (2)Position of gear mark 'CC' at No 1 cylinder's beginning of injection (3)B.T.D.C.: aa (4)-
----------
aa=7deg
----------
a=(100deg)

Information:

(1) End play for shaft (new) ... 0.114 0.038 mm (.0045 .0015 in) Maximum permissible end play (worn) ... 0.20 mm (.008 in)(2) Thickness of thrust bearing (where thrust rings contact bearing) ... 5.36 0.03 mm (.211 .001 in)(3) Diameter of shaft (new) ... 15.997 to 16.005 mm (.6298 to .6301 in) Bore in the bearing (new) ... 16.035 to 16.043 mm (.6313 to .6316 in)Maximum permissible clearance between bearing and shaft (worn) ... 0.05 mm (.002 in)(4) Maximum permissible gap of oil seal ring, measured in bore of housing ... 0.25 mm (.010 in)(5) Install the compressor wheel (at room temperature) as follows: a. Put compressor wheel on the shaft.b. Put a small amount of clean engine oil on the threads.c. Tighten the nut to 14 to 17 N m (125 to 150 lb in).
Do not bend or add stress to the shaft when nut is loosened or tightened.
d. Remove nut from shaft and apply 6V1541 Quick Cure Primer on the threads of the shaft and nut followed by application of 9S3263 Retaining Compound.e. Tighten nut to 4 N m (30 lb in).f. Tighten nut more 90° rotation.(6) Thickness of each thrust ring ... 2.553 0.013 mm (.1005 .0005 in)(7) Bore in housing (new) ... 24.994 to 25.006 mm (.9840 to .9845 in) Outside diameter of the bearing (new) ... 24.882 to 24.892 mm (.9796 to .9800 in)Maximum permissible clearance between bearing and bore in housing (worn) ... 0.15 mm (.006 in)Tighten both band clamps (that hold the compressor and turbine housings to the cartridge group) with procedure that follows: a. Tighten to ... 14 1.1 N m (125 10 lb in)b. Tap (hit) clamp lightly all around.c. Tighten again to ... 14 1.1 N m (125 10 lb in)
Do not overtighten the clamps.
Torque for four nuts (put 5P3931 Anti-Seize Compound on threads) and bolts that hold turbocharger to exhaust manifold ... 55 5 N m (40 4 lb ft) Put clean engine oil in the oil inlet of the turbocharger after assembly or before installation to provide start up lubrication and/or storage protection.Turbocharger (S3B and C3B)
(1) End play for shaft (new) ... 0.102 0.025 mm (.004 .001 in) Maximum permissible end play (worn) ... 0.20 mm (.008 in)(2) Thickness of thrust bearing (where thrust rings contact bearing) ... 5.36 0.03 mm (.211 .001 in)(3) Diameter of shaft (new) ... 12.697 to 12.705 mm (.4999 to .5002 in) Bore in the bearing (new) ... 12.741 to 12.748 mm (.5016 to .5019 in)Maximum permissible clearance between bearing and shaft (worn) ... 0.05 mm (.002 in)(4) Maximum permissible gap of oil seal ring, measured in bore of housing ... 0.25 mm (.010 in)(5) Install the compressor wheel (at room temperature) as follows: a. Put compressor wheel on the shaft.b. Put a small amount of clean engine oil on the threads.c. Tighten the nut to 14 to 17 N m (125 to 150 lb