101402-3970 ZEXEL 9 400 612 647 BOSCH INJECTION-PUMP ASSEMBLY 9400612647 1014023970 3863639

Information Cross number Calibration Data Calibration Data Ex

Information injection-pump assembly

BOSCH 9 400 612 647 9400612647

ZEXEL 101402-3970 1014023970

KOMATSU 3863639 3863639

Price: query

Buy now
Add to cart Go to cart

Rating:

Buy INJECTION-PUMP ASSEMBLY 101402-3970 zexel genuine, new aftermarket engine parts with delivery

Service parts 101402-3970 INJECTION-PUMP ASSEMBLY:

1. _

2. FUEL INJECTION PUMP 101041-9340

3. GOVERNOR 105404-5360

4. SUPPLY PUMP

105220-5960

5. AUTOM. ADVANCE MECHANIS

6. COUPLING PLATE

7. COUPLING PLATE

8. _

9. _

10. NOZZLE AND HOLDER ASSY

11. Nozzle and Holder

12. Open Pre:MPa(Kqf/cm2) 21.6{220}

13. NOZZLE-HOLDER

14. NOZZLE

15. NOZZLE SET

Include in #1:

101402-3970 as INJECTION-PUMP ASSEMBLY

108622-3911 as _

Cross reference number

BOSCH 9 400 612 647 9400612647

ZEXEL 101402-3970 1014023970

KOMATSU 3863639 3863639

Zexel num

Bosch num

Firm num

Name

101402-3970

9 400 612 647

3863639 KOMATSU

INJECTION-PUMP ASSEMBLY
S4D102E K

101402-3970

9 400 612 647

6732711260 KOMATSU

INJECTION-PUMP ASSEMBLY
S4D102E K

Calibration Data:

Adjustment conditions

Test oil
1404 Test oil ISO4113 or {SAEJ967d}

Test oil temperature degC 40 40 45

Nozzle and nozzle holder 105780-8140

Bosch type code EF8511/9A

Nozzle 105780-0000

Bosch type code DN12SD12T

Nozzle holder 105780-2080

Bosch type code EF8511/9

Opening pressure MPa 17.2

Opening pressure kgf/cm2 175

Injection pipe
Outer diameter - inner diameter - length (mm) mm 6-2-600

Overflow valve 131424-3420

Overflow valve opening pressure kPa 255 255 255

Overflow valve opening pressure kgf/cm2 2.6 2.6 2.6

Tester oil delivery pressure kPa 157 157 157

Tester oil delivery pressure kgf/cm2 1.6 1.6 1.6

Direction of rotation (viewed from drive side)
Right R

Injection timing adjustment

Direction of rotation (viewed from drive side)
Right R

Injection order 1-3-4-2

Pre-stroke mm 2.5 2.45 2.55

Beginning of injection position
Drive side NO.1

Difference between angles 1
Cal 1-3 deg. 90 89.5 90.5

Difference between angles 2
Cal 1-4 deg. 180 179.5 180.5

Difference between angles 3
Cyl.1-2 deg. 270 269.5 270.5

Injection quantity adjustment

Adjusting point A

Rack position 10.8

Pump speed r/min 1250 1250 1250

Average injection quantity mm3/st. 79.5 78.5 80.5

Max. variation between cylinders % 0 -2.5 2.5

Basic *

Fixing the lever *

Boost pressure kPa 41.3 41.3

Boost pressure mmHg 310 310

Hydraulic cylinder ON *

Injection quantity adjustment_02

Adjusting point C

Rack position 8.9+-0.5

Pump speed r/min 335 335 335

Average injection quantity mm3/st. 9 8 10

Max. variation between cylinders % 0 -15 15

Fixing the rack *

Boost pressure kPa 0 0 0

Boost pressure mmHg 0 0 0

Hydraulic cylinder ON *

Injection quantity adjustment_03

Adjusting point D

Rack position -

Pump speed r/min 100 100 100

Average injection quantity mm3/st. 75 75 85

Fixing the lever *

Boost pressure kPa 0 0 0

Boost pressure mmHg 0 0 0

Hydraulic cylinder OFF *

Rack limit *

Boost compensator adjustment

Pump speed r/min 750 750 750

Rack position 10.75

Boost pressure kPa 17.3 16 18.6

Boost pressure mmHg 130 120 140

Boost compensator adjustment_02

Pump speed r/min 750 750 750

Rack position 11.2

Boost pressure kPa 28 21.3 34.7

Boost pressure mmHg 210 160 260

Test data Ex:

Governor adjustment

N:Pump speed R:Rack position (mm) (1)Target notch: K (2)Tolerance for racks not indicated: +-0.05mm. (3)RACK LIMIT (When hydraulic cylinder is OFF) (4)Boost compensator stroke: BCL (5)When hydraulic cylinder ON: P1 (6)Rack difference between N = N1 and N = N2 (7)Adjust the secondary timing before adjusting the governor.
----------
K=12 BCL=0.45+-0.1mm P1=((392)kPa{(4)kgf/cm2}) N1=1250r/min N2=750r/min
----------

Speed control lever angle

F:Full speed I:Idle (1)Stopper bolt setting
----------

----------
a=18deg+-5deg b=28deg+-5deg

Stop lever angle

N:Pump normal S:Stop the pump. (1)No return spring
----------

----------
a=0deg+-5deg b=53deg+-5deg

Timing setting

(1)Pump vertical direction (2)Key groove position at No. 1 cylinder's beginning of injection position (at BTDC: aa). (3)Position of the key groove of the No. 1 cylinder at B.T.D.C. bb (fix the governor flyweight at this position for delivery). (4)B.T.D.C.: aa (5)At second timing adjustment, set the camshaft at the * position and tighten the flyweight locknut. (6)Align the flyweight's timing gear position with the lockpin groove and then fully tighten the flyweight to the camshaft. (7)Remove the lock pin and adjust the governor. Reinstall the lock pin to fix the flyweight for delivery.
----------
aa=16deg bb=0deg
----------
a=54deg54min+-3deg b=8deg+-30min

Information:

Sequence For Rocker Arm Bolts(1) Bore in rocker arm for shaft (new) ... 24.803 0.013 mm (.9765 .0005 in.) Diameter of shaft (new) ... 24.752 0.013 mm (.9745 .0005 in.)(2) Put 2P2506 Thread Lubricant on the threads of all bolts that hold rocker arm shaft and tighten the bolts in the following step sequence. 1. Tighten bolts 1 through 4 in number sequence to ... 280 27 N m (210 20 lb.ft.)2. Tighten bolts 1 through 4 in number sequence to ... 440 20 N m (320 15 lb.ft.)3. Tighten bolts 1 through 4 in number sequence again to ... 440 20 N m (320 15 lb.ft.)(3) Torque for locknut for valve adjustment screw ... 28 4 N m (22 3 lb.ft.)(4) Torque for locknut for bridge adjustment screw ... 28 4 N m (22 3 lb.ft.)(5) Clearance for valves: Intake valves ... 0.38 mm (.015 in.)Exhaust valves ... 0.76 mm (.030 in.)(6) Height to top of dowel ... 53.3 0.5 mm (2.10 .02 in.)(7) Diameter of dowel (new) ... 11.008 0.003 mm (.4334 .0001 in.) Bore in bridge for dowel (new) ... 11.13 0.05 mm (.438 .002 in.)Bore in head for dowel ... 10.968 0.020 mm (.4318 .0008 in.)(8) Diameter of valve lifter (new) ... 27.896 0.013 mm (1.0983 .0005 in.) Bore in block for valve lifter (new) ... 27.9527 0.0190 mm (1.10050 .00075 in.) See Guideline For Reusable Parts; Salvage Of Lifter Bores in 3400 Family Engines, Form No. SEBF8069 for the procedure, tooling and specifications needed to install 4W4588 Sleeves for salvage of the lifter bores in the cylinder block.(9) 6N6872 Lifter Guide Spring. See Guideline For Reusable Parts, Form No. SEBF8066, for information on using guide springs again. (10) 2N7229 Spring: Length under test force ... 74.2 mm (2.92 in.)Test force ... 45 to 53 N (10 to 12 lb.)Free length after test ... 114.3 mm (4.50 in.)Outside diameter ... 29.7 mm (1.17 in.)(11) Dowel length above top surface of rocker shaft support to be (both ends) ... 12.7 1.0 mm (.50 .04 in.)(12) Clearance for rocker arms (both ends) ... 0.30 to 1.40 mm (.012 to .055 in.)(13) Use 2N7228 Washer as needed to get clearance (12).