Information holder & nozzle se
Rating:
Components :
| 001. | HOLDER & NOZZLE SE | 09350-00901 |
Scheme ###:
| 000. | [01] | 09350-00901 | HOLDER & NOZZLE SE | 23610-1130 |
| 000. | [01] | 09350-00901 | HOLDER & NOZZLE SE | S2361-01130 |
| 001. | [01] | 09310-00901 | HOLDER ASSY, NOZZL | 23630-1150 |
| 001-001. | [01] | 09311-10561 | BODY | 23612-1090 |
| 001-002. | [01] | 09312-10151 | PIN, NOZZLE HOLDER | 23616-1150 |
| 001-003. | [01] | 09312-70020 | SPRING, NOZZLE HOL | 6 303 1700 20 |
| 001-004. | [01] | 09313-10080 | SCREW, ADJUST | 23614-1110 |
| 001-005. | [01] | 09324-50052 | WASHER | 22847-1290 |
| 001-006. | [01] | 09313-40150 | NUT, CAP | 23623-1200 |
| 001-007. | [01] | 09316-20060 | SCREW, CYLINDER | 23665-1100 |
| 001-008. | [01] | 09316-40460 | NUT, NOZZLE RETAIN | 23633-1180 |
| 001-009. | [01] | 09316-60010 | SCREW, HOLLOW | 22835-1240 |
| 001-010. | [02] | 94901-81020 | WASHER, COPPER PLA | 22867-1500A |
| 002. | [01] | 09340-00010 | NOZZLE ASSY | 2362A-76010 |
Include in #3:
09350-00901
as HOLDER & NOZZLE SE
09350-00901
Cross reference number
| Part num | Firm num | Firm | Name |
| 09350-00901 | 23610-1130 | HOLDER & NOZZLE SE |
Information:
Engine Crankshaft Will Not Turn
Recommended Procedure
1. Low or No Battery Voltage ... Check battery voltage. If battery voltage is less than 8 volts for a 12 volt system, or 16 volts for a 24 volt system, put a charge to the battery. If battery will not hold a charge, load test the battery as shown in the Electrical System of the Testing and Adjusting section of this Service Manual.2. Bad Switch, Bad Wiring or Connection in Switch Circuit ... With ignition switch in START position, check voltage at switch connection on starter solenoid. If there is no voltage, or if the voltage is low at this connection, check wiring, connections, ignition switch, and magnetic switch (if used).3. Bad Cable or Connection; Battery to Starter ... With ignition switch in the START position, check voltage at connection of battery cable to starter. If there is no voltage, or if the voltage is low at this
Recommended Procedure
1. Low or No Battery Voltage ... Check battery voltage. If battery voltage is less than 8 volts for a 12 volt system, or 16 volts for a 24 volt system, put a charge to the battery. If battery will not hold a charge, load test the battery as shown in the Electrical System of the Testing and Adjusting section of this Service Manual.2. Bad Switch, Bad Wiring or Connection in Switch Circuit ... With ignition switch in START position, check voltage at switch connection on starter solenoid. If there is no voltage, or if the voltage is low at this connection, check wiring, connections, ignition switch, and magnetic switch (if used).3. Bad Cable or Connection; Battery to Starter ... With ignition switch in the START position, check voltage at connection of battery cable to starter. If there is no voltage, or if the voltage is low at this