105220-7090 ZEXEL 9 441 610 221 BOSCH SUPPLY PUMP 9441610221 1052207090


 

Information supply pump

BOSCH 9 441 610 221 9441610221
ZEXEL 105220-7090 1052207090
105220-7090 SUPPLY PUMP
Rating:
55
Buy SUPPLY PUMP 105220-7090 zexel genuine, new aftermarket engine parts with delivery

Scheme ###:

1. [1] 152062-0020 PUMP HOUSING
2. [1] 152030-0300 STOP PIN
5. [1] 152100-2301 PUMP PLUNGER
6. [1] 152102-0400 COMPRESSION SPRING
7. [1] 152105-1500 CAPSULE
8. [1] 139526-0000 GASKET
14. [2] 152115-0500 VALVE BODY
14. [2] 152115-0500 VALVE BODY
15. [2] 152116-0200 COILED SPRING
15. [2] 152116-0200 COILED SPRING
17. [1] 152118-0900 ADAPTOR
18. [2] 029631-6060 O-RING
18. [2] 029631-6060 O-RING
25. [1] 152200-6721 HAND PRIMER
30. [1] 152300-6920 EYE BOLT
32. [1] 139814-0900 EYE BOLT
33. [1] 139814-0500 INLET UNION
35. [2] 029341-4130 GASKET D20&13.8T2*
36. [2] 029341-4130 GASKET D20&13.8T2*

Cross reference number

Zexel num
Bosch num
Firm num
Name
105220-7090 
9 441 610 221 
NP-FP/KSP-AD 
   
SUPPLY PUMP
K 14GC FEED PUMP F/P




Information:

Below 0°C (32°F)
Ether is poisonous and flammable. Do not store replacement cylinders in living areas or in the operator's compartment.Do not smoke while changing ether cylinders.Use ether only in well ventilated areas.Use it with care to avoid fires.Keep the ether cylinders out of the reach of unauthorized persons.Avoid breathing of the vapors or repeated contact of ether with skin.Do not store cylinders in direct sunlight.Do not puncture or burn cylinders.Discard cylinders in a safe place.
Do not use excessive starting fluid during starting or after the engine is running. Engine damage can result. Do not crank the engine for more than 30 seconds. Allow 2 minutes for the starter to cool before cranking again.
Turn the battery disconnect switch (if equipped) OFF after the engine is stopped to prevent battery discharge, while starter motor is cooling.1. Repeat steps 1 through 4 in the "Above 0°C (32°F)" procedure.2. Try to start engine without ether. If it does not start, then use ether.3. While cranking the engine, spray starting fluid (ether) sparingly, into the engine air inlet or push the starting aid control switch and hold for three seconds (time required to fill chamber). Ether is injected when aid switch is released.Use additional starting fluid once every two seconds until engine runs smoothly.If oil pressure does not register within 15 seconds, stop the engine immediately to prevent damage.4. Do not apply load to the engine or increase engine speed until oil pressure and all temperature gauges reach operating temperature. Check all gauges during the warm-up period.For starting below -18°C (0°F), use of optional cold weather starting aids are recommended. A coolant heater or extra battery capacity may be required.Temperatures below -23°C (-10°F), consult your Caterpillar dealer or refer to the "Cold Weather Operation Guide," Form SEBU5338, available from your Caterpillar dealer.

Have questions with 105220-7090?





Group cross 105220-7090 ZEXEL

 
 

Nissan-Diesel 

9 441 610 239 
NP-FP/KSP-AD 
16640Z5569 
SUPPLY PUMP

Nissan 

9 441 610 240 
NP-FP/KSP-A 
16640Z5568 
SUPPLY PUMP

Nissan-Diesel 

9 441 610 240 
NP-FP/KSP-A 
16640Z5568 
SUPPLY PUMP
9 441 610 220 
NP-FP/KSP-A 
 
SUPPLY PUMP

Yanmar 

9 441 610 266 
NP-FP/KSP-AD 
12760552100 
SUPPLY PUMP

Nissan-Diesel 

9 441 610 188 
NP-FP/KSP-A 
16640Z5571 
SUPPLY PUMP
9 441 610 202 
NP-FP/KSP-AD 
1664095008 
SUPPLY PUMP
9 441 610 565 
NP-FP/KSP-A 
 
SUPPLY PUMP
F 01G 19U 001 
NP-FP/KSP-A 
 
SUPPLY PUMP
105220-7090  
9 441 610 221 
NP-FP/KSP-AD 
 
SUPPLY PUMP
Back to top