Information supply pump
BOSCH
9 440 610 071
9440610071
ZEXEL
105220-4991
1052204991
Rating:
Compare Prices: .
As an associate, we earn commssions on qualifying purchases through the links below
MeiHongHong 105220-4932 105220-4991 105220-6250 8941327070 Compatible For Isuzu Engine 4BG1 6BD1 4BD1 EX200-2 SH200 Compatible For Komatsu Engine 6D105 Excavator PC200-3 PC220-3 Compatible For Hitachi
MeiHongHong 105220-4932 105220-4991 105220-6250 8941327070 Compatible For Isuzu Engine 4BG1 6BD1 4BD1 EX200-2 SH200 || Compatible For Komatsu Engine 6D105 Excavator PC200-3 PC220-3 Compatible For Hitachi EX120-5 EX150-5 || Replacement Fuel Pump || fuel pump module assembly can prevent noise from the fuel tank, difficult to start, and high temperature standstill || direct replacement of OEM components, easy installation
MeiHongHong 105220-4932 105220-4991 105220-6250 8941327070 Compatible For Isuzu Engine 4BG1 6BD1 4BD1 EX200-2 SH200 || Compatible For Komatsu Engine 6D105 Excavator PC200-3 PC220-3 Compatible For Hitachi EX120-5 EX150-5 || Replacement Fuel Pump || fuel pump module assembly can prevent noise from the fuel tank, difficult to start, and high temperature standstill || direct replacement of OEM components, easy installation
Fuel Pump Compatible with Hitachi Excavator EX120-5 EX150-5 Fit for 105220-4932 105220-4991
AMPSTOE Fits Isuzu EX100 4BD1 Engine; For Hitachi Excavator EX120-5 EX150-5 || Part Number: For 105220-4932 105220-4991 105220-6250 1052204932 1052204991 1052206250 || Package includes: 1X Fuel Pump as pictured || Please check the pictures and description before ordering it. Make sure it's what you need. || If you have any problems after purchasing, please contact us in time before opening return or case.
AMPSTOE Fits Isuzu EX100 4BD1 Engine; For Hitachi Excavator EX120-5 EX150-5 || Part Number: For 105220-4932 105220-4991 105220-6250 1052204932 1052204991 1052206250 || Package includes: 1X Fuel Pump as pictured || Please check the pictures and description before ordering it. Make sure it's what you need. || If you have any problems after purchasing, please contact us in time before opening return or case.
LHCBSOK 105220-6250 105220-4991 105220-4932 Fuel Transfer Lift Pump Compatible with Isuzu Engine 4BD1 EX200-2 SH200 4BG1 6BD1 Compatible with Komatsu Engine 6D105 Excavator PC200-3 PC220-3
LHCBSOK Part Number: 105220-6250 105220-4991 105220-4932 || Part Name: Fuel Transfer Lift Pump || Application: Compatible with Isuzu Engine 4BD1 EX200-2 SH200 4BG1 6BD1; Compatible with Komatsu Engine 6D105 Excavator PC200-3 PC220-3 || Friendly tips: This product is stable and reliable. The information provided is for reference purposes only. Before purchasing, please confirm the part number and compare it to the old part. || Note: If you encounter any issues, such as unpaid customs duties when signing for delivery, please don't worry. We will be here to assist you.
LHCBSOK Part Number: 105220-6250 105220-4991 105220-4932 || Part Name: Fuel Transfer Lift Pump || Application: Compatible with Isuzu Engine 4BD1 EX200-2 SH200 4BG1 6BD1; Compatible with Komatsu Engine 6D105 Excavator PC200-3 PC220-3 || Friendly tips: This product is stable and reliable. The information provided is for reference purposes only. Before purchasing, please confirm the part number and compare it to the old part. || Note: If you encounter any issues, such as unpaid customs duties when signing for delivery, please don't worry. We will be here to assist you.
Scheme ###:
| 1. | [1] | 152003-0720 | PUMP HOUSING |
| 5. | [1] | 152100-1120 | PUMP PLUNGER |
| 6. | [1] | 152102-0400 | COMPRESSION SPRING |
| 7. | [1] | 152105-1500 | CAPSULE |
| 8. | [1] | 029332-6030 | GASKET |
| 10. | [1] | 152111-2820 | TAPPET |
| 10/2. | [1] | 152112-0100 | ROLLER |
| 10/3. | [1] | 152113-0700 | BEARING PIN |
| 10/4. | [2] | 152114-0400 | SLIDER |
| 14. | [2] | 152115-0200 | VALVE BODY |
| 14. | [2] | 152115-0200 | VALVE BODY |
| 15. | [2] | 152116-0200 | COILED SPRING |
| 15. | [2] | 152116-0200 | COILED SPRING |
| 17. | [1] | 152118-0900 | ADAPTOR |
| 18. | [1] | 029631-6060 | O-RING |
| 19. | [1] | 029631-6060 | O-RING |
| 20. | [1] | 152121-0200 | LOCKING WASHER |
| 25. | [1] | 152200-5420 | HAND PRIMER |
| 30. | [1] | 152300-3820 | EYE BOLT |
| 32. | [1] | 029731-4580 | EYE BOLT |
| 35. | [2] | 029341-4080 | GASKET |
| 36. | [2] | 029341-4080 | GASKET |
Include in #1:
101421-4781
as SUPPLY PUMP
Cross reference number
Zexel num
Bosch num
Firm num
Name
Information:
2. Loosen clamp (1).3. Remove two bolts (2).4. Remove two bolts (3) and washers.5. Remove water pump (4) and the gasket. When installing replace the gasket. Make sure all gasket surfaces are clean and free of dirt. For installation of the water pump, reverse the removal steps.6. Fill the radiator with coolant to the proper level. See the Operation & Maintenance Manual.Disassemble & Assemble Water Pump
The following tools are needed for disassembly. Start By:a. remove water pump 1. Remove bolt (15) and the washer. Remove bearing (12) and gear (10) as a unit.2. Use Tool (A), (C) and a press, and remove bearing (12) from gear (10).3. Remove snap ring (8) with Tool (B).4. Remove two bolts (1), the washers, cover (14) and gasket (2) from water pump housing (18).5. Loosen bolt (13) approximately 6.4 mm (.25 in). Hit the bolt with a soft hammer to loosen impeller (16) from shaft (9).6. Remove bolt (13), washer (11), impeller (16), spring (3) and seal assembly (4) from shaft (9).7. Remove bearing (7) and shaft (9) as a unit.8. Use Tool (A), (C) and a press to remove bearing (7) from shaft (9).9. Remove ceramic seal (5) and seal (17) from water pump housing (18).10. Use Tool (C) to remove lip-type seal (6) from the water pump housing. The following steps are for assembly of the water pump. The following tools are needed for assembly. 11. Install lip-type seal (6) in water pump housing (18) with Tool (C). The lip of the seal must be toward the bearings. Put clean engine oil on the lip of the seal.12. Install shaft (9) in bearing (7) with a press.13. Install shaft (9) and bearing (7) as a unit in water pump housing (18).14. Install snap ring (8) with Tool (B).
Clean water only is permitted for use as a lubricant for assembly. Do not damage or put hands on the wear surface of the carbon ring or the ceramic ring. Install the ceramic ring with the smoothest face of the ring toward the carbon seal assembly.
15. Put ceramic ring (5) in position in seal (17). Use hand pressure and Tool (D) to install the ceramic ring.16. Remove spring (3) from seal assembly (4). Use hand pressure and Tool (D) to install the seal assembly. Push seal assembly (4) on shaft (9) until it makes light contact with ceramic ring (5).17. Install spring (3) on seal assembly (4). Put impeller (16) in position on shaft (9), and install washer (11) and bolt (13) that hold it. Tighten bolt (13) to a torque of 38.0 1.5 N m (28 1 lb ft).18. Put gasket (2) and cover (14) in position on water pump housing (18). Install the two washers and bolts (1) that hold them.19. Install bearing (12) on gear (10) with a press.20. Position gear (10) and bearing (12) as a unit on shaft (9). Install the washer and bolt (15) that hold them together. Tighten bolt (15) to a torque of
The following tools are needed for disassembly. Start By:a. remove water pump 1. Remove bolt (15) and the washer. Remove bearing (12) and gear (10) as a unit.2. Use Tool (A), (C) and a press, and remove bearing (12) from gear (10).3. Remove snap ring (8) with Tool (B).4. Remove two bolts (1), the washers, cover (14) and gasket (2) from water pump housing (18).5. Loosen bolt (13) approximately 6.4 mm (.25 in). Hit the bolt with a soft hammer to loosen impeller (16) from shaft (9).6. Remove bolt (13), washer (11), impeller (16), spring (3) and seal assembly (4) from shaft (9).7. Remove bearing (7) and shaft (9) as a unit.8. Use Tool (A), (C) and a press to remove bearing (7) from shaft (9).9. Remove ceramic seal (5) and seal (17) from water pump housing (18).10. Use Tool (C) to remove lip-type seal (6) from the water pump housing. The following steps are for assembly of the water pump. The following tools are needed for assembly. 11. Install lip-type seal (6) in water pump housing (18) with Tool (C). The lip of the seal must be toward the bearings. Put clean engine oil on the lip of the seal.12. Install shaft (9) in bearing (7) with a press.13. Install shaft (9) and bearing (7) as a unit in water pump housing (18).14. Install snap ring (8) with Tool (B).
Clean water only is permitted for use as a lubricant for assembly. Do not damage or put hands on the wear surface of the carbon ring or the ceramic ring. Install the ceramic ring with the smoothest face of the ring toward the carbon seal assembly.
15. Put ceramic ring (5) in position in seal (17). Use hand pressure and Tool (D) to install the ceramic ring.16. Remove spring (3) from seal assembly (4). Use hand pressure and Tool (D) to install the seal assembly. Push seal assembly (4) on shaft (9) until it makes light contact with ceramic ring (5).17. Install spring (3) on seal assembly (4). Put impeller (16) in position on shaft (9), and install washer (11) and bolt (13) that hold it. Tighten bolt (13) to a torque of 38.0 1.5 N m (28 1 lb ft).18. Put gasket (2) and cover (14) in position on water pump housing (18). Install the two washers and bolts (1) that hold them.19. Install bearing (12) on gear (10) with a press.20. Position gear (10) and bearing (12) as a unit on shaft (9). Install the washer and bolt (15) that hold them together. Tighten bolt (15) to a torque of