Information supply pump
BOSCH
9 440 610 249
9440610249
ZEXEL
105207-1260
1052071260
YANMAR
12861952010
12861952010
Rating:
Scheme ###:
| 1. | [1] | 152000-4620 | PUMP HOUSING |
| 5. | [1] | 152100-1120 | PUMP PLUNGER |
| 6. | [1] | 152102-0400 | COMPRESSION SPRING |
| 7. | [1] | 152105-1500 | CAPSULE |
| 8. | [1] | 029332-6030 | GASKET |
| 10. | [1] | 152111-3221 | TAPPET |
| 10/2. | [1] | 152112-0500 | ROLLER |
| 10/3. | [1] | 152113-1000 | BEARING PIN |
| 10/4. | [2] | 152114-1600 | SLIDER |
| 14. | [2] | 152115-0200 | VALVE BODY |
| 14. | [2] | 152115-0200 | VALVE BODY |
| 15. | [2] | 152116-0200 | COILED SPRING |
| 15. | [2] | 152116-0200 | COILED SPRING |
| 16. | [1] | 152117-0400 | CAPSULE |
| 18. | [2] | 029331-6030 | GASKET |
| 18. | [2] | 029331-6030 | GASKET |
| 20. | [1] | 152121-0200 | LOCKING WASHER |
| 25. | [1] | 152200-2120 | HAND PRIMER |
| 30. | [1] | 152300-5920 | EYE BOLT |
| 32. | [1] | 029731-4680 | EYE BOLT |
| 33. | [1] | 027114-1040 | INLET UNION |
| 34. | [1] | 027114-1040 | INLET UNION |
| 35. | [2] | 026514-1840 | GASKET D17.9&14.2T1 |
| 36. | [2] | 026514-1840 | GASKET D17.9&14.2T1 |
| 42. | [1] | 152320-0100 | COVER |
Include in #1:
106671-4240
as SUPPLY PUMP
Cross reference number
Zexel num
Bosch num
Firm num
Name
Information:
Lubricate, Oil - To apply a material to a surface to reduce
Pry - To raise, move or open with a lever.
Remove - To take off.
Route - To install a harness, hose, or wire along a specific course or layout along or through a product, to direct along a predefined path.
Special Tool - To work with a nonstandard device.
Tighten - To make nearer to fully stretched, without slack, to apply tension or torque.Torque Specifications
Refer to Torque Specifications, SENR3130 for the most up-to-date torque specifications for standard fasteners.Tooling Required
The table below contains the tooling needed for this procedure.
Table 39
Item Qty Part Number Part Name Illustration (Substep) Location
T1 1 5F-4764 Pry Bar Illustration 6 (1) Fuel Injector Removal
Illustration 2 g06285426
Illustration 3 g06285429
Illustration 4 g06285477
Illustration 5 g06285492
Illustration 6 g06285497Fuel Injector Installation
Illustration 7 g06285503
Illustration 8 g06285515
Illustration 9 g06285527
Illustration 10 g06285536
Refer to the appropriate Testing and Adjusting manual to check or reset the engine valve lash.
Illustration 11 g06285542Reference Section
Pry - To raise, move or open with a lever.
Remove - To take off.
Route - To install a harness, hose, or wire along a specific course or layout along or through a product, to direct along a predefined path.
Special Tool - To work with a nonstandard device.
Tighten - To make nearer to fully stretched, without slack, to apply tension or torque.Torque Specifications
Refer to Torque Specifications, SENR3130 for the most up-to-date torque specifications for standard fasteners.Tooling Required
The table below contains the tooling needed for this procedure.
Table 39
Item Qty Part Number Part Name Illustration (Substep) Location
T1 1 5F-4764 Pry Bar Illustration 6 (1) Fuel Injector Removal
Illustration 2 g06285426
Illustration 3 g06285429
Illustration 4 g06285477
Illustration 5 g06285492
Illustration 6 g06285497Fuel Injector Installation
Illustration 7 g06285503
Illustration 8 g06285515
Illustration 9 g06285527
Illustration 10 g06285536
Refer to the appropriate Testing and Adjusting manual to check or reset the engine valve lash.
Illustration 11 g06285542Reference Section