Information shim
BOSCH
9 411 610 461
9411610461
ZEXEL
139400-0200
1394000200
ISUZU
1156390890
1156390890

Rating:
Include in ###:
Cross reference number
Zexel num
Bosch num
Firm num
Name
139400-0200
9 411 610 461
1156390890 ISUZU
SHIM
C 90HY SHIM Standard parts Others
C 90HY SHIM Standard parts Others
139400-0200
9 411 610 461
228114850A HINO
SHIM
C 90HY SHIM Standard parts Others
C 90HY SHIM Standard parts Others
139400-0200
9 411 610 461
228814850A HINO
SHIM
A C 90HY SHIM Standard parts Others
A C 90HY SHIM Standard parts Others
139400-0200
9 411 610 461
228816860A HINO
SHIM
B C 90HY SHIM Standard parts Others
B C 90HY SHIM Standard parts Others
139400-0200
9 411 610 461
ME727663 MITSUBISHI
SHIM
C 90HY SHIM Standard parts Others
C 90HY SHIM Standard parts Others
139400-0200
9 411 610 461
1671699017 NISSAN-DIESEL
SHIM
C 90HY SHIM Standard parts Others
C 90HY SHIM Standard parts Others
Information:
Introduction
The following special instructions must be used to test for a crack in the Diesel Particulate Filter (DPF). Do not perform any procedure that is outlined in this Special Instruction until you have read and understand the information that is contained in this document.Required Tools
Table 1
Required Tools    
Tool     Part Number     Part Description     Qty    
A     380-5200     Tool Kit     1    
B     366-7782     Attenuator     1    Testing Procedure
Perform a "Manual Diesel Particulate Filter Regeneration" using the electronic service tool.
After the manual DPF regeneration is complete, operate the engine at 1800 rpm for a MINIMUM of 20 minutes to stabilize the DPF temperatures.Note: The engine must maintain a steady speed for the entire duration of the test.
Hot engine components can cause injury from burns. Before performing maintenance on the engine, allow the engine and the components to cool.
Illustration 1 g02597531
Typical example (1) DPF Outlet Cap (2) Filter Paper (3) Hose Assembly (4) Air Pump
Illustration 2 g03655197
Typical example
Stop the engine. Disconnect harness assembly from both soot antennae. Remove outlet soot antenna (5). Refer to
The following special instructions must be used to test for a crack in the Diesel Particulate Filter (DPF). Do not perform any procedure that is outlined in this Special Instruction until you have read and understand the information that is contained in this document.Required Tools
Table 1
Required Tools    
Tool     Part Number     Part Description     Qty    
A     380-5200     Tool Kit     1    
B     366-7782     Attenuator     1    Testing Procedure
Perform a "Manual Diesel Particulate Filter Regeneration" using the electronic service tool.
After the manual DPF regeneration is complete, operate the engine at 1800 rpm for a MINIMUM of 20 minutes to stabilize the DPF temperatures.Note: The engine must maintain a steady speed for the entire duration of the test.
Hot engine components can cause injury from burns. Before performing maintenance on the engine, allow the engine and the components to cool.
Illustration 1 g02597531
Typical example (1) DPF Outlet Cap (2) Filter Paper (3) Hose Assembly (4) Air Pump
Illustration 2 g03655197
Typical example
Stop the engine. Disconnect harness assembly from both soot antennae. Remove outlet soot antenna (5). Refer to
Have questions with 139400-0200?
Group cross 139400-0200 ZEXEL
Isuzu
139400-0200
9 411 610 461
1156390890
SHIM
Hino
139400-0200
9 411 610 461
228114850A
SHIM
139400-0200
9 411 610 461
228814850A
SHIM
139400-0200
9 411 610 461
228816860A
SHIM
Mitsubishi
139400-0200
9 411 610 461
ME727663
SHIM
Nissan-Diesel
139400-0200
9 411 610 461
1671699017
SHIM