Information plunger-and-barrel assy
BOSCH
9 443 610 064
9443610064
ZEXEL
140151-1920
1401511920
KUBOTA
1411251041
1411251041
Rating:
Compare Prices: .
As an associate, we earn commssions on qualifying purchases through the links below
$90.44
25 Jan 2024
0.1102[0.05] Pounds
CN: CHENG2568MALL
Diesel Fuel Pump Element K15 Plunger 140151-1920
NAttco The pump plunger is usually connected to the piston rod by a plunger rod or connecting rod. || The diameter of the plunger rod and the choice of material have an effect on the strength and stiffness of the pump plunger. || The pump plunger usually has a raised top and groove to house the seal ring. || The sealing ring is used to ensure that fluid does not leak around the plunger rod. || The action of the pump plunger is usually reciprocating, pushing liquid or gas from the intake port to the outlet.
NAttco The pump plunger is usually connected to the piston rod by a plunger rod or connecting rod. || The diameter of the plunger rod and the choice of material have an effect on the strength and stiffness of the pump plunger. || The pump plunger usually has a raised top and groove to house the seal ring. || The sealing ring is used to ensure that fluid does not leak around the plunger rod. || The action of the pump plunger is usually reciprocating, pushing liquid or gas from the intake port to the outlet.
$54.29
09 Sep 2024
KR: Adabus
140151-1820 K14 140151-1920 K15 K198 Fuel Pump Plunger Element
Generic Placement on vehicle: Fuel injection pump || Country/region of manufacture: China || Material type: iron || Item weight: 0.5KG
Generic Placement on vehicle: Fuel injection pump || Country/region of manufacture: China || Material type: iron || Item weight: 0.5KG
$81.35
29 Mar 2023
LV: Gear245
Bosch Service kit 9443610064
BOSCH
BOSCH
Include in ###:
Cross reference number
Zexel num
Bosch num
Firm num
Name
140151-1920
1411251041 KUBOTA
PLUNGER-AND-BARREL ASSY
C 26AA PLUNGER ASSY PL(PFR-Agriculture) PL
C 26AA PLUNGER ASSY PL(PFR-Agriculture) PL
140151-1920
1430151041 KUBOTA
PLUNGER-AND-BARREL ASSY
A C 26AA PLUNGER ASSY PL(PFR-Agriculture) PL
A C 26AA PLUNGER ASSY PL(PFR-Agriculture) PL
140151-1920
1466151041 KUBOTA
PLUNGER-AND-BARREL ASSY
B C 26AA PLUNGER ASSY PL(PFR-Agriculture) PL
B C 26AA PLUNGER ASSY PL(PFR-Agriculture) PL
140151-1920
1468151041 KUBOTA
PLUNGER-AND-BARREL ASSY
C C 26AA PLUNGER ASSY PL(PFR-Agriculture) PL
C C 26AA PLUNGER ASSY PL(PFR-Agriculture) PL
Information:
Camshaft
When reconditioning an engine, check the diameter of the camshaft bearing journals and the camshaft lobe height.Camshaft bearing journals have a diameter of 2.5000 .0005 in. (63.500 0.013 mm) and the minimum diameter worn is 2.4970 in. (63.424 mm).To find lobe lift (A) of camshaft, use the following procedure:1. Measure lobe height (B) of one exhaust and one intake lobe.2. Measure base circle (C) of one exhaust and one intake lobe.3. Subtract base circle (C) dimension (STEP 2) from lobe height (B) dimension (STEP 1). The difference is actual lobe lift (A).4. The specified (new) lobe lift (A) is: (a) Exhaust lobe ... .3071 in.(7.800 mm)(b) Intake lobe ... .3077 in.(7.816 mm)5. The maximum permissible difference between actual lobe lift (STEP 3) and specified lobe lift (STEP 4) is .025 in. (0.64 mm).
CAMSHAFT LOBE
A. Lobe lift. B. Lobe height. C. Base circle.With camshaft installed in the cylinder block, check end play. End play with new components should be .007 .003 in. (0.18 0.08 mm). The maximum permissible end play is .020 in. (0.51 mm).Camshaft Followers
Use an 8S2293 Magnet to remove the cam followers.
REMOVING CAM FOLLOWERSCam followers establish a wear pattern with the camshaft lobes. Identify and reinstall the followers removed. Dishing or circular wear pattern is allowed on the cam follower face, providing the wear face keeps a polished appearance. Replace the follower if the wear face is rough or shows signs of scuffing. A new follower can be used with an old camshaft, providing the lobe is in good condition. Put engine oil on the cam followers and the camshaft lobes before installing the cam followers. Use new cam followers with a new camshaft.Camshaft Gears
1. Remove screw (1) and washer (2) from end of camshaft.
REMOVING TIMING ADVANCE RETAINING SCREW
1. Screw. 2. Washer.2. Remove timing advance unit from the camshaft.3. Install puller (A), with spacer (C) over the shaft in the camshaft spacer (B) on spacer (C) as shown and remove the gear from the camshaft.
REMOVING GEAR (Typical Example)
A. 1P2321 Puller. B. 8S5579 Spacer. C. 9S9155 Spacer.To install the gear use the following procedure:1. Heat the gear to a temperature of approximately 400°F (204°C) before installing on the camshaft.
Do not heat the gear with a torch. Do not heat the gear to a temperature of more than 600°F (315°C). Heating the gear with a torch or to a temperature of more than 600°F (315°C) may cause the two drive dowels for the automatic timing advance to loosen and come out of the gear.
2. Align slot in gear hub with the pin in the camshaft. Install the gear on the camshaft with timing mark on gear aligned with timing mark on crankshaft gear. Be sure the gear is completly seated against the shoulder of the camshaft.
Do not drive the gear on the camshaft.
3. Align holes in weights with dowels in gear and install the automatic timing advance.4. Align pin (3) in washer with hole (4) in camshaft and install washer (2).5. Install screw (1) and
When reconditioning an engine, check the diameter of the camshaft bearing journals and the camshaft lobe height.Camshaft bearing journals have a diameter of 2.5000 .0005 in. (63.500 0.013 mm) and the minimum diameter worn is 2.4970 in. (63.424 mm).To find lobe lift (A) of camshaft, use the following procedure:1. Measure lobe height (B) of one exhaust and one intake lobe.2. Measure base circle (C) of one exhaust and one intake lobe.3. Subtract base circle (C) dimension (STEP 2) from lobe height (B) dimension (STEP 1). The difference is actual lobe lift (A).4. The specified (new) lobe lift (A) is: (a) Exhaust lobe ... .3071 in.(7.800 mm)(b) Intake lobe ... .3077 in.(7.816 mm)5. The maximum permissible difference between actual lobe lift (STEP 3) and specified lobe lift (STEP 4) is .025 in. (0.64 mm).
CAMSHAFT LOBE
A. Lobe lift. B. Lobe height. C. Base circle.With camshaft installed in the cylinder block, check end play. End play with new components should be .007 .003 in. (0.18 0.08 mm). The maximum permissible end play is .020 in. (0.51 mm).Camshaft Followers
Use an 8S2293 Magnet to remove the cam followers.
REMOVING CAM FOLLOWERSCam followers establish a wear pattern with the camshaft lobes. Identify and reinstall the followers removed. Dishing or circular wear pattern is allowed on the cam follower face, providing the wear face keeps a polished appearance. Replace the follower if the wear face is rough or shows signs of scuffing. A new follower can be used with an old camshaft, providing the lobe is in good condition. Put engine oil on the cam followers and the camshaft lobes before installing the cam followers. Use new cam followers with a new camshaft.Camshaft Gears
1. Remove screw (1) and washer (2) from end of camshaft.
REMOVING TIMING ADVANCE RETAINING SCREW
1. Screw. 2. Washer.2. Remove timing advance unit from the camshaft.3. Install puller (A), with spacer (C) over the shaft in the camshaft spacer (B) on spacer (C) as shown and remove the gear from the camshaft.
REMOVING GEAR (Typical Example)
A. 1P2321 Puller. B. 8S5579 Spacer. C. 9S9155 Spacer.To install the gear use the following procedure:1. Heat the gear to a temperature of approximately 400°F (204°C) before installing on the camshaft.
Do not heat the gear with a torch. Do not heat the gear to a temperature of more than 600°F (315°C). Heating the gear with a torch or to a temperature of more than 600°F (315°C) may cause the two drive dowels for the automatic timing advance to loosen and come out of the gear.
2. Align slot in gear hub with the pin in the camshaft. Install the gear on the camshaft with timing mark on gear aligned with timing mark on crankshaft gear. Be sure the gear is completly seated against the shoulder of the camshaft.
Do not drive the gear on the camshaft.
3. Align holes in weights with dowels in gear and install the automatic timing advance.4. Align pin (3) in washer with hole (4) in camshaft and install washer (2).5. Install screw (1) and