Information plunger-and-barrel assy
BOSCH
9 443 610 557
9443610557
ZEXEL
134151-9020
1341519020
NISSAN-DIESEL
1679599117
1679599117
Rating:
Compare Prices: .
As an associate, we earn commssions on qualifying purchases through the links below
Diesel Fuel Pump P112 134151-9020 Plunger Element P103 134151-2220 Plunger For Komatsu Excavator - (Color: P103 134151-2220)
Generic Color: P103 134151-2220
Generic Color: P103 134151-2220
Diesel Fuel Pump U4441 PT40 Plunger Element For Kubota - (Color: P112 134151-9020)
Generic Color: P112 134151-9020
Generic Color: P112 134151-9020
You can express buy:
USD 4.72
11-11-2022
11-11-2022
Include in ###:
Number on scheme 7/2
1060607590
as PLUNGER-AND-BARREL ASSY
1060615561
as PLUNGER-AND-BARREL ASSY
P170
1060615590
as PLUNGER-AND-BARREL ASSY
1060615591
as PLUNGER-AND-BARREL ASSY
P170
1060615921
as PLUNGER-AND-BARREL ASSY
1060615922
as PLUNGER-AND-BARREL ASSY
P170
1060617020
as PLUNGER-AND-BARREL ASSY
1060617241
as PLUNGER-AND-BARREL ASSY
P170
1060617390
as PLUNGER-AND-BARREL ASSY
1060617391
as PLUNGER-AND-BARREL ASSY
P170
1060617550
as PLUNGER-AND-BARREL ASSY
1060617690
as PLUNGER-AND-BARREL ASSY
P170
1060671800
as PLUNGER-AND-BARREL ASSY
Cross reference number
Zexel num
Bosch num
Firm num
Name
134151-9020
9 443 610 557
1679599117 NISSAN-DIESEL
PLUNGER-AND-BARREL ASSY
C 14EU PLUNGER ASSY PL(P) PL
C 14EU PLUNGER ASSY PL(P) PL
Information:
Illustration 1 g00564355
7W-2743 Electronic Speed Switch (ESS)
(1) Push button for Overspeed Verification
(2) Reset button
(3) Overspeed indicator lamp
(4) Seal screw plug for adjusting the engine overspeed
(5) Seal screw plug for adjusting the crank terminate speed
(6) Seal screw plug for adjusting the oil step pressure speed setting The procedure for the magnetic pickup test will determine if the operation of the magnetic pickup is correct.
Connect a 6V-7070 Digital Multimeter to the "COM" terminal and the "SIG" terminal. The terminals are (ESS-3)and (ESS-4) of the ESS. Set the meter voltage scale to a scale that is greater than 1.5 VAC. Start the engine. Run the engine at low idle or 600 rpm. Choose the one that is larger. If the voltage that is measured is 1.5 VAC or more, the operation of the magnetic pickup is correct. If the voltage is less than 1.5 VAC, go to Step 2.
Stop the engine. Disconnect the wiring for the magnetic pickup at the plug-in connector. Connect the voltmeter to the connector terminals of the magnetic pickup. Start the engine. Run the engine at low idle or 600 rpm. Choose the one that is larger. If the voltage that is measured is 1.5 VAC or more, repair the wiring that is between the magnetic pickup and the ESS. If the voltage is less than 1.5 VAC, go to Step 3.
Illustration 2 g00564913
Magnetic pickup
(1) Clearance
(2) Magnetic pickup
(3) Wires to the connector
(4) Locknut
(5) Flywheel housing
(6) Ring gear
Loosen locknut (4) and turn magnetic pickup (2) in the counterclockwise direction in order to remove magnetic pickup (2) from flywheel housing (5). Turn the flywheel until a gear tooth of ring gear (6) is directly in the center of the threaded hole for magnetic pickup (2). Install magnetic pickup (2) in flywheel housing (5).
Turn magnetic pickup (2) in the clockwise direction until the end of magnetic pickup (2) slightly touches the gear tooth. Turn the magnetic pickup for one-half turn in the counterclockwise direction in order to set correct clearance (1). Tighten locknut (4) to a torque of 45 7 N m (33 5 lb ft). Note: Do not allow the magnetic pickup to turn while the locknut is tightened.
Repeat Step 2. If the voltage is still less than 1.5 VAC, replace the magnetic pickup.
Have questions with 134151-9020?
Group cross 134151-9020 ZEXEL
Nissan-Diesel
134151-9020
9 443 610 557
1679599117
PLUNGER-AND-BARREL ASSY