Information plunger-and-barrel a
BOSCH
9 413 614 194
9413614194
ZEXEL
131154-5620
1311545620
Rating:
Compare Prices: .
As an associate, we earn commssions on qualifying purchases through the links below
131154-5620 Fuel Injection Plunger Power Sprayer Pump A298 Diesel Element For Komatsu PC200LC-7 Excavator 4D102 Engine Parts - (Color: 6PCS 131154-5620)
Generic Color: 6PCS 131154-5620 || Komatsu PC200LC-7 || For engines: Komatsu 4D102, 6D102, S6D102, SA6D102, SA6D102E, 4D102, S4D102, S4D102E || SAA6D102E-2DD-8, SAA6D102E-2F-8, SAA6D102E-2FF-8, SAA4D102E-2D-4, SAA4D102E-2F-4, SAA6D102E-2A-8, SAA6D102E-2C, SAA6D102E-2C-8, SAA6D102E-2C-9, SAA6D102E-2CC, SAA6D102E-2CC-8, SAA6D102E-2D-8, SAA6D102E-2E, SAA6D102E-2E-8, SAA6D102E-2G-8 || 4BT, 6BTAA diesel engine
Generic Color: 6PCS 131154-5620 || Komatsu PC200LC-7 || For engines: Komatsu 4D102, 6D102, S6D102, SA6D102, SA6D102E, 4D102, S4D102, S4D102E || SAA6D102E-2DD-8, SAA6D102E-2F-8, SAA6D102E-2FF-8, SAA4D102E-2D-4, SAA4D102E-2F-4, SAA6D102E-2A-8, SAA6D102E-2C, SAA6D102E-2C-8, SAA6D102E-2C-9, SAA6D102E-2CC, SAA6D102E-2CC-8, SAA6D102E-2D-8, SAA6D102E-2E, SAA6D102E-2E-8, SAA6D102E-2G-8 || 4BT, 6BTAA diesel engine
Plunger Pump Repair Kit 131154-5620 Fuel Injection Plunger Spare Assembly Diesel Pump Barrel A298 Fit for Komatsu PC200-7 PC270-7 4D102 6D102 Pack of 6
Cabezales Manufacturer MFR Number：131154-5620 , 1311545620 Stamping No. A298 || Package: 6 Pieces of Fuel Diesel Pump Plunger and Barrel.Neutral Packing || Fit for Komatsu PC200-7 4D102 6D102 || Notice:Please You Carefully Check Your Vehicle's Pump Plunger Barrel And Make Sure That The Number Must Be Completely The Same As Our Description Fitment || Interchange Number.: 9413614194 , 9 413 614 194
Cabezales Manufacturer MFR Number：131154-5620 , 1311545620 Stamping No. A298 || Package: 6 Pieces of Fuel Diesel Pump Plunger and Barrel.Neutral Packing || Fit for Komatsu PC200-7 4D102 6D102 || Notice:Please You Carefully Check Your Vehicle's Pump Plunger Barrel And Make Sure That The Number Must Be Completely The Same As Our Description Fitment || Interchange Number.: 9413614194 , 9 413 614 194
$227.59
27 Jul 2024
KR: Adabus
diesel plunger 131154-5620 A298 plunger x 12 pieces
Generic Is customized: yes || Material type: || Item length: 5x5x5 || Origin: Mainland China
Generic Is customized: yes || Material type: || Item length: 5x5x5 || Origin: Mainland China
You can express buy:
USD 29.5
10-11-2022
10-11-2022
USD 30
10-11-2022
10-11-2022
USD 4.72
11-11-2022
11-11-2022
Images:
USD 5.13
[24-Jun-2019]
USD 5.13
[24-Jun-2019]
USD 4.19
[29-Jun-2019]
Include in ###:
Cross reference number
Zexel num
Bosch num
Firm num
Name
131154-5620
9 413 614 194
PLUNGER-AND-BARREL A
C 14EL PLUNGER ASSY PL(A) PL
C 14EL PLUNGER ASSY PL(A) PL
Information:
Introduction
This Special Instruction provides detailed instructions on the installation of the sleeve into the compensator group of the 3408E and 3412E Unit Injector Hydraulic Pump. If leaks are experienced at the joint of the compensator and the adapter block, the 174-8943 Sleeve may be installed to improve sealing. The new press fit sleeve contains the O-ring more securely than the original slip fit sleeve.Note: Engines built prior to the serial number break that contain the new sleeve have a "S" stamped at the end of the part number on the serial number plate of the pump. The reworked part numbers appear as "144-0835-06S". Individual Components
Table 1
Quantity Part Number Part Description
1 174-8943 Sleeve
1 135-2652 O-Ring
1 033-6039 O-Ring
6 9X-7680 O-Ring Necessary Tools
One of the following tools may be used to insert the new sleeve into the compensator group.
A 31.750 mm (1.250 inch) diameter flat plate.
The 1P-0467 Drive Plate from 1P-0510 Driver Group .
An acceptable bearing insertion tool.Removal Of The O-Ring Seals
Illustration 1 g00638376
Remove the four bolts (1) from the compensator (2). Remove the compensator and the adapter. Do not adjust the compensator. Refer to Special Instruction, REHS0192-03, step 3 of procedure for "Disassembly of the 144-0835 Unit Injector Hydraulic Pump Group ".
Illustration 2 g00638368
Remove the four O-ring seals (3) from the bottom side of the adapter. Refer to Special Instruction, REHS0192-03, step 4 of procedure for "Disassembly of the 144-0835 Unit Injector Hydraulic Pump Group ".
Illustration 3 g00638372
Remove the four O-ring seals (4) from the two housings. Refer to Special Instruction, REHS0192-03, step 5 of procedure for "Disassembly of the 144-0835 Unit Injector Hydraulic Pump Group ".
Remove the slip fit sleeve from the compensator housing.Installation Of The Sleeve
Illustration 4 g00637918
(1) Compensator assembly. (2) 174-8943 Sleeve .
Invert the compensator assembly (1). Hold the compensator assembly securely within a vise or a press table.
Start the sleeve (2) by hand into the compensator assembly (1) .Note: It is important that the groove on the outside diameter of the sleeve is oriented toward the O-ring in the joint. If this is not done, there will not be sufficient room to properly seal the O-ring.
Press the sleeve (2) flush with the surface of the compensator assembly (1) using the 1P-0467 Drive Plate or by using an acceptable bearing insertion tool.Installation Of The O-Ring Seals
Illustration 5 g00638368
Install the four O-ring seals (3) on the bottom side of the adapter. Refer to Special Instruction, REHS0192-03, step 16 of procedure for "Assembly of the 144-0835 Unit Injector Hydraulic Pump Group ".
Illustration 6 g00638372
Install the four O-rings (4) on the two housings. Refer to Special Instruction, REHS0192-03, step 17 of procedure for "Assembly of the 144-0835 Unit Injector Hydraulic Pump Group ".
Illustration 7 g00638376
Install the compensator assembly (2) and the adapter as a unit vertically so that the O-rings seals are not damaged. Tighten the four bolts (1) to the following torque.Torque for bolts ... 8 1 N
This Special Instruction provides detailed instructions on the installation of the sleeve into the compensator group of the 3408E and 3412E Unit Injector Hydraulic Pump. If leaks are experienced at the joint of the compensator and the adapter block, the 174-8943 Sleeve may be installed to improve sealing. The new press fit sleeve contains the O-ring more securely than the original slip fit sleeve.Note: Engines built prior to the serial number break that contain the new sleeve have a "S" stamped at the end of the part number on the serial number plate of the pump. The reworked part numbers appear as "144-0835-06S". Individual Components
Table 1
Quantity Part Number Part Description
1 174-8943 Sleeve
1 135-2652 O-Ring
1 033-6039 O-Ring
6 9X-7680 O-Ring Necessary Tools
One of the following tools may be used to insert the new sleeve into the compensator group.
A 31.750 mm (1.250 inch) diameter flat plate.
The 1P-0467 Drive Plate from 1P-0510 Driver Group .
An acceptable bearing insertion tool.Removal Of The O-Ring Seals
Illustration 1 g00638376
Remove the four bolts (1) from the compensator (2). Remove the compensator and the adapter. Do not adjust the compensator. Refer to Special Instruction, REHS0192-03, step 3 of procedure for "Disassembly of the 144-0835 Unit Injector Hydraulic Pump Group ".
Illustration 2 g00638368
Remove the four O-ring seals (3) from the bottom side of the adapter. Refer to Special Instruction, REHS0192-03, step 4 of procedure for "Disassembly of the 144-0835 Unit Injector Hydraulic Pump Group ".
Illustration 3 g00638372
Remove the four O-ring seals (4) from the two housings. Refer to Special Instruction, REHS0192-03, step 5 of procedure for "Disassembly of the 144-0835 Unit Injector Hydraulic Pump Group ".
Remove the slip fit sleeve from the compensator housing.Installation Of The Sleeve
Illustration 4 g00637918
(1) Compensator assembly. (2) 174-8943 Sleeve .
Invert the compensator assembly (1). Hold the compensator assembly securely within a vise or a press table.
Start the sleeve (2) by hand into the compensator assembly (1) .Note: It is important that the groove on the outside diameter of the sleeve is oriented toward the O-ring in the joint. If this is not done, there will not be sufficient room to properly seal the O-ring.
Press the sleeve (2) flush with the surface of the compensator assembly (1) using the 1P-0467 Drive Plate or by using an acceptable bearing insertion tool.Installation Of The O-Ring Seals
Illustration 5 g00638368
Install the four O-ring seals (3) on the bottom side of the adapter. Refer to Special Instruction, REHS0192-03, step 16 of procedure for "Assembly of the 144-0835 Unit Injector Hydraulic Pump Group ".
Illustration 6 g00638372
Install the four O-rings (4) on the two housings. Refer to Special Instruction, REHS0192-03, step 17 of procedure for "Assembly of the 144-0835 Unit Injector Hydraulic Pump Group ".
Illustration 7 g00638376
Install the compensator assembly (2) and the adapter as a unit vertically so that the O-rings seals are not damaged. Tighten the four bolts (1) to the following torque.Torque for bolts ... 8 1 N
Have questions with 131154-5620?
Group cross 131154-5620 ZEXEL
131154-5620
9 413 614 194
PLUNGER-AND-BARREL A