105160-4710 ZEXEL 9 430 610 572 BOSCH NOZZLE AND HOLDER ASSY. 9430610572 1051604710 16600z5666


 

Information nozzle and holder assy.

BOSCH 9 430 610 572 9430610572
ZEXEL 105160-4710 1051604710
NISSAN-DIESEL 16600Z5666 16600z5666
105160-4710 NOZZLE AND HOLDER ASSY.
Rating:
85
Buy NOZZLE AND HOLDER ASSY. 105160-4710 zexel genuine, new aftermarket engine parts with delivery

Include in #1:

101608-9370 as NOZZLE AND HOLDER ASSY

Cross reference number

Zexel num
Bosch num
Firm num
Name
105160-4710 
9 430 610 572 
30-4820E4 
16600Z5666  NISSAN-DIESEL
NOZZLE AND HOLDER ASSY.
FE6A K 53KB NOZZLE & HOLDER ASSY N&NH KBL-S N&NH




Information:


Table 1
S O S Oil Sampling Interval for Engine crankcase
Recommended Interval (1)(2) Oil Type
Every 250 Service Hours Cat DEO
Cat DEO-ULS
(1) Severe applications may require a more frequent oil sampling interval.
(2) Under certain conditions, the Cat dealer or the Operation and Maintenance Manual may allow a longer interval between oil samplings.Note: Refer to the Operation and Maintenance Manual for your engine for recommended oil drain intervals.Consult your Cat dealer for complete information and assistance in order to establish an S O S Services program for your engine.More Frequent S O S Sampling Improves Life Cycle Management
Traditionally, the suggested S O S sampling intervals for diesel engines have been at 250 hours. However in severe applications, more frequent oil sampling is recommended. Severe service for lubricated compartments occurs at high loads, in high temperatures, and in dusty conditions. If any of these conditions or other severe service indicators exist, sample the engine oil at 125 hour intervals. These additional samples will increase the chance of detecting a potential failure.Determining Optimum Oil Change Intervals
Sampling the engine oil at every 125 hours provides information for oil condition and for oil performance. This information is used to determine the optimum usable life of a particular oil. Also, more points of data will allow closer monitoring of component wear rates. Close monitoring also allows you to obtain the maximum use of the oil. For detailed information on optimizing oil change intervals, consult your Cat dealer.This Special Publication does not address recommended oil drain intervals. Refer to your engine Operation and Maintenance Manual, and consult your Cat dealer for additional guidance, including but not limited to guidance on establishing optimized and/or acceptable oil drain intervals.To reduce the potential risk of failures associated with extended oil drain periods, Caterpillar recommends that oil drain intervals only be extended based on oil analysis, and subsequent system inspections. Oil analysis alone does not provide an indication of the rate of formation of lacquer, varnish and/or other deposits on surfaces. The only accurate way to evaluate specific oil performance in a specific system using extended oil drain periods is to observe the effects on the system components. Making these observations involves tear-down inspections of systems that have run to the normal overhaul period while using extended oil drain intervals. Following this recommendation will help ensure that excessive component wear does not take place in a given application.Note: The use of Cat S O S Services oil analysis helps environmental sustainability as the best way to optimize oil life. S O S Services will help engines reach expected life. Consult your Cat dealer regarding the testing required to establish a safe, optimized oil drain interval.Standard oil drain intervals as published in engine Operation and Maintenance Manual are for typical applications:
Using recommended oils
Using good fuel
Using recommended filters
Using industry standard good maintenance practices
Following maintenance intervals as published in engine Operation and Maintenance ManualMore severe applications may require shortened oil drain intervals, while less severe applications may allow for longer than standard oil drain intervals. High

Have questions with 105160-4710?





Group cross 105160-4710 ZEXEL

Isuzu 

9 430 610 571 
30-3251R 
1153003610 
NOZZLE AND HOLDER ASSY.
6SD1MTCY

Nissan-Diesel 

105160-4710  
9 430 610 572 
30-4820E4 
16600Z5666 
NOZZLE AND HOLDER ASSY.
FE6A

Hino 

9 430 610 573 
30-4840 
236003010A 
NOZZLE AND HOLDER ASSY.
P09C-TD
9 430 610 573 
30-4840 
S236003010 
NOZZLE AND HOLDER ASSY.
P09C-TD
9 430 610 574 
30-32013A 
 
NOZZLE AND HOLDER ASSY.
6105Q1

Isuzu 

9 430 613 082 
1153000081 
NOZZLE AND HOLDER ASSY.
E120
9 430 610 575 
30-3201L 
1153003600 
NOZZLE AND HOLDER ASSY.
6SD1TQA1
9 430 613 081 
30-3201R 
1153003601 
NOZZLE AND HOLDER ASSY.
6SD1TQA1

Nissan-Diesel 

9 430 610 178 
31-4650F1 
16600Z5671 
NOZZLE AND HOLDER ASSY.
FE6

Hino 

9 430 613 079 
236003070A 
NOZZLE AND HOLDER ASSY.
J08C-TP
9 430 610 576 
30-2010A 
236003170A 
NOZZLE AND HOLDER ASSY.
J08C-TN

Dpico 

9 430 613 093 
 
NOZZLE AND HOLDER ASSY.
K7
Back to top