Information nozzle and holder assy.
BOSCH
F 01G 0V4 001
f01g0v4001
ZEXEL
105158-5012
1051585012
KOMATSU
4063269
4063269
Rating:
Compare Prices: .
As an associate, we earn commssions on qualifying purchases through the links below
#14 x 3/4" Hex Washer Head Self Drilling Tek Screws, Stainless Steel 410, Full Thread, Plain Finish, Self-Drilling, Quantity 1000 by Fastenere
Fastenere Hex washer head self drilling screws have a drill point at the tip of the thread drills its own pilot hole in to metal allowing for quick installation and fastening while saving time and effort with just a single step || Made from an ultra strong stainless steel grade 410 giving them the ability to drill through sheet metal and stainless steel while still being wear resistant and offering a mild chemical corrosion protection; these screws are not intended for use with aluminum as the higher iron content in the fastener will cause embrittlement; 410 Stainless steel is always MAGNETIC due to the higher iron content giving the drilling capabilities || These screws have a hex head that can be driven with a nut driver or socket and can be adjusted with a wrench; the built in flanged washer adds a secure grip to the material being fastened into while also preventing the head from crushing thin metal || The self drilling point also referred to as a tek can self drill metal up to a thickness of 0.090 inches and is best used with a lot of pressure and a slow drill speed; if drilling too fast you could run the risk of over heating the metal drilling tip which could cause it to wear out or warp || Fastenere brand self drilling tapping screws will tap their own thread into the material being screwed into creating a long lasting vibration resistant connection that is the choice for use with corrugated roof siding and sheet metal applications
Fastenere Hex washer head self drilling screws have a drill point at the tip of the thread drills its own pilot hole in to metal allowing for quick installation and fastening while saving time and effort with just a single step || Made from an ultra strong stainless steel grade 410 giving them the ability to drill through sheet metal and stainless steel while still being wear resistant and offering a mild chemical corrosion protection; these screws are not intended for use with aluminum as the higher iron content in the fastener will cause embrittlement; 410 Stainless steel is always MAGNETIC due to the higher iron content giving the drilling capabilities || These screws have a hex head that can be driven with a nut driver or socket and can be adjusted with a wrench; the built in flanged washer adds a secure grip to the material being fastened into while also preventing the head from crushing thin metal || The self drilling point also referred to as a tek can self drill metal up to a thickness of 0.090 inches and is best used with a lot of pressure and a slow drill speed; if drilling too fast you could run the risk of over heating the metal drilling tip which could cause it to wear out or warp || Fastenere brand self drilling tapping screws will tap their own thread into the material being screwed into creating a long lasting vibration resistant connection that is the choice for use with corrugated roof siding and sheet metal applications
Include in #1:
101405-3250
as NOZZLE AND HOLDER ASSY
Cross reference number
Zexel num
Bosch num
Firm num
Name
105158-5012
4063269 KOMATSU
NOZZLE AND HOLDER ASSY.
4BTAA K 53LP NOZZLE & HOLDER ASSY N&NH
4BTAA K 53LP NOZZLE & HOLDER ASSY N&NH
Information:
When all details are filled in, select "Submit".Note: Two labels and a serial number plate will be sent to the dealer address. If two labels are not received, contact Global_Engine_Marking.
Illustration 19 g03159376
Install the new emissions certification film (6), information label (7), and serial number plate on the cylinder block according to the installation instructions received with the labels and plate.Note: Destroy the old emissions certification film and serial number plate.Operation and Maintenance information
There are several specific messages on this machine. The exact location of the messages and the description of the messages are reviewed in this section. Become familiarized with all messages.Make sure that all of the messages are legible. Clean the messages or replace the messages if you cannot read the words. Replace the illustrations if the illustrations are not legible. When you clean the messages, use a cloth, water, and soap. Do not use solvent, gasoline, or other harsh chemicals to clean the messages. Solvents, gasoline, or harsh chemicals could loosen the adhesive that secures the messages. Loose adhesive will allow the messages to fall.Replace any message that is damaged, or missing. If a message is attached to a part that is replaced, install a message on the replacement part. Any Cat® dealer can provide new messages.
Illustration 20 g03504876
Location of films (1) Engine Oil film (2) Engine Oil film (3) Diesel Fuel Requirements film (4) Diesel Fuel Requirements filmEngine Oil (1) and (2)
This film is located next to the engine oil filler tube and on the case drain filter cover on the right side of the machine.
Illustration 21 g02448560
Typical ExampleCat® DEO-ULS oils and oils that satisfy the "API CJ-4" and/or "ACEA E9" requirements are required for engines that are equipped with a diesel particulate filter.Diesel Fuel Requirements (3) and (4)
This film is located next to the fuel cap on the right side and the left side of the machine.
Illustration 22 g03619316
Typical ExampleUse Ultralow Sulfur Diesel (ULSD) fuel.The Environmental Protection Agency (EPA) defines Ultra-Low Sulfur Diesel (ULSD - S15) as a diesel fuel with a sulfur content not to exceed 15 parts per million (ppm(mg/kg)) or 0.0015 percent by weight. Engines are equipped with exhaust after-treatment systems are designed to run on ULSD only. Use of LSD or fuels higher than 15 ppm (mg/kg) sulfur in these engines will reduce engine efficiency and engine durability. Damage to the emissions control systems and/or shortened service interval will occur. Failures that result form the use of fuels are not Caterpillar factory defects. Therefore the cost of repairs would not be covered by a Caterpillar warranty.In Europe, ultra low sulfur diesel fuel will have a maximum of 0.0010 percent (10 ppm(mg/kg)) sulfur and is typically referred to as "sulfur-free". This sulfur level is defined in European Standard "EN 590:2004".Lubricant Viscosities - Fluids Recommendations
Engine Oil
Cat® oils have been developed and tested to provide the full performance and life that has been designed and built into Cat® engines.
Illustration 23 g02448560
Typical ExampleCat® DEO-ULS or oils that meet the Cat® ECF-3 specification and the API CJ-4 are required for