105158-2321 ZEXEL 9 430 610 499 BOSCH NOZZLE AND HOLDER ASSY. 9430610499 1051582321


 

Information nozzle and holder assy.

BOSCH 9 430 610 499 9430610499
ZEXEL 105158-2321 1051582321
105158-2321 NOZZLE AND HOLDER ASSY.
Rating:
44
Buy NOZZLE AND HOLDER ASSY. 105158-2321 zexel genuine, new aftermarket engine parts with delivery

Cross reference number

Zexel num
Bosch num
Firm num
Name
105158-2321 
105158-2322 
9 430 610 499 
88-1140 
   
NOZZLE AND HOLDER ASSY.
4JG2 * K 53KP N&NH KDA-P N&NH




Information:

Test Procedure
System Operation
The SLC 5/04 diagnostic indicators are located on the front of the following components: Power Supply, CPU and I/O Modules.The diagnostic indicators help trace the source of the fault. Faults can be found in the following components: Input devices, Output devices, Wiring and The controller.The thermocouple module has five LED indicators. Four of the LED indicators are "Channel Status" indicators. The "Channel Status" indicators are numbered according to the channel. One of the LED indicators is a "Module Status" indicator.Diagnostics are displayed on the "Module Status" LED indicator. Operating errors are displayed on the "Module Status" LED indicator. Problems may be detected during powerup or problems may be detected during operation. When an error occurs, the module will not communicate with the processor. The channel is disabled and the data is cleared.
Illustration 1 g00563417
Diagram of the LED indicators
Illustration 2 g00563392
Diagram of the LED indicators
Illustration 3 g00563575
Diagram of the RTD module
Illustration 4 g00563579
Schematic of the RTD moduleFunctional Test
The "Module Status" LED is on. The module is operating normally. Stop.
The "Channel Status" LED is on. The module is operating normally. Stop.
The "Module Status" LED is off. The module is in a fault condition. Proceed to 6.
The "Channel Status" LED is off. The channel is not enabled. This is normal if the sensor is not wired.
The "Channel Status" LED is blinking. The module is in a fault condition. Proceed to 10.
Check the electrical connectors and check the wiring.
Bodily contact with electrical potential can cause bodily injury or death.To avoid the possibility of injury or death, ensure that the main power supply has been disconnected before performing any maintenance or removing any modules.
Disconnect the power supply.
Check the electrical connectors and check the wiring for damage or bad connections.
Verify that all modules are properly seated.
Verify the status of the LED on the SLC 5/04.The results of the preceding procedure are in the following list:
All of the components are fully installed. All of the components are free of corrosion. All of the components are free of damage. All of the modules are properly seated. Proceed to 7.
The components are not fully installed. The components are not free of corrosion. The components are damaged. All of the modules are not properly seated. Repair the component. Verify that the repair resolves the problem. STOP.
Check the LED indicator on the module.
Connect the power supply.
Cycle the power to the module.The results of the preceding procedure are in the following list:
No errors are displayed on the LED indicators. Stop.
Errors are displayed on the LED indicators. Proceed to 8.
Check the module for a fault.
Bodily contact with electrical potential can cause bodily injury or death.To avoid the possibility of injury or death, ensure that the main power supply has been disconnected before performing any maintenance or removing any modules.
To avoid potential damage to the processor, handle all modules by the ends of the carrier or edges of the plastic housing. Skin oil or dirt can corrode metallic surfaces, inhibiting electrical contact.
Disconnect the power supply.
Remove the module from the chassis.Reference: Maintenance Procedure, "Input Module

Have questions with 105158-2321?





Group cross 105158-2321 ZEXEL

9 430 610 122 
 
NOZZLE AND HOLDER ASSY.
9 430 610 140 
0150 
 
NOZZLE AND HOLDER ASSY.
4JG2TC

Isuzu 

9 430 613 711 
0150 
8970886730 
NOZZLE AND HOLDER ASSY.
4JG2TC
9 430 610 497 
88-1130 
 
NOZZLE AND HOLDER ASSY.
4JG2TC

Isuzu 

9 430 613 595 
0150 
8970886740 
NOZZLE AND HOLDER ASSY.
4JG2TC
9 430 610 498 
88-1140 
 
NOZZLE AND HOLDER ASSY.
105158-2321  

105158-2322 
9 430 610 499 
88-1140 
 
NOZZLE AND HOLDER ASSY.
4JG2

Isuzu 

9 430 613 713 
88-1140 
8970796530 
NOZZLE AND HOLDER ASSY.
4JG2
9 430 610 500 
88-1140 
 
NOZZLE AND HOLDER ASSY.

Isuzu 

9 430 610 501 
88-1140 
8971055440 
NOZZLE AND HOLDER ASSY.
4JG2
9 430 610 502 
88-1090P 
5866363860 
NOZZLE AND HOLDER ASSY.
4EE1-TC
9 430 610 503 
88-1150 
 
NOZZLE AND HOLDER ASSY.
4JG2

Isuzu 

9 430 613 712 
88-1150 
8971256020 
NOZZLE AND HOLDER ASSY.
4JG2
9 430 613 191 
8971256030 
NOZZLE AND HOLDER ASSY.
4JG2

Nissan 

9 430 610 504 
88-1120L 
1660089TA4 
NOZZLE AND HOLDER ASSY.
4JG2

Isuzu 

9 430 613 700 
L88-1120 
8971431960 
NOZZLE AND HOLDER ASSY.
4JG2
9 430 610 505 
88-1120L 
 
NOZZLE AND HOLDER ASSY.
4JG2

Isuzu 

9 430 613 704 
L88-1120 
8971438210 
NOZZLE AND HOLDER ASSY.
4JG2
9 430 610 506 
88-1160 
 
NOZZLE AND HOLDER ASSY.
4JG2T

Isuzu 

9 430 613 703 
88-1160 
8972128410 
NOZZLE AND HOLDER ASSY.
4JG2T
Back to top