105158-2300 ZEXEL 9 430 610 122 BOSCH NOZZLE AND HOLDER ASSY. 9430610122 1051582300


 

Information nozzle and holder assy.

BOSCH 9 430 610 122 9430610122
ZEXEL 105158-2300 1051582300
105158-2300 NOZZLE AND HOLDER ASSY.
Rating:
38
Buy NOZZLE AND HOLDER ASSY. 105158-2300 zexel genuine, new aftermarket engine parts with delivery

Cross reference number

Zexel num
Bosch num
Firm num
Name
105158-2300 
105158-2301 
9 430 610 122 
   
NOZZLE AND HOLDER ASSY.
* K




Information:


Accidental engine starting can cause injury or death to personnel working on the equipment.To avoid accidental engine starting, disconnect the battery cable from the negative (−) battery terminal. Completely tape all metal surfaces of the disconnected battery cable end in order to prevent contact with other metal surfaces which could activate the engine electrical system.Place a Do Not Operate tag at the Start/Stop switch location to inform personnel that the equipment is being worked on.
Water Temperature Fault (WT)
The current flow for the circuit that is described in this section is applicable for all engines. The engine must be running at a speed with a coolant temperature that is hot enough to close the water temperature contactor switch (WTS). The water temperature contactor switch is normally open. The following events occur in the electric circuit in order to shut down the engine. The engine will shut down when the temperature of the coolant system is greater than the maximum temperature that is set for the WTS.
The water temperature contactor switch (WTS) closes across the contacts , which are normally open.
Closing the contacts (WTS-1) and (WTS-2) opens the circuit to slave relay (SR1) (line 33).
When the open circuit de-energizes (SR1) and (SR2), the circuit opens across the relay contacts (SR1-30) and (SR1-87) (line 43).
The open circuit de-energizes the fuel solenoid (FS) which shuts off the fuel flow to the engine. The starter motor circuit can then be engaged. However, there is no fuel flow to the engine and the engine cannot be restarted until the coolant temperature falls below the rating of the water temperature contactor switch. When the water temperature is below the maximum rating for the temperature of the WTS, the circuit opens across contacts (WTS-1) and (WTS-2). The slave relay (SR1) and the fuel solenoid (FS) can then be energized by the engine starting circuit in order to restart the engine.
To avoid possible engine damage or another immediate shutdown, the water temperature fault must be corrected before attempting to restart the engine.
Accidental engine starting can cause injury or death to personnel working on the equipment.To avoid accidental engine starting, disconnect the battery cable from the negative (−) battery terminal. Completely tape all metal surfaces of the disconnected battery cable end in order to prevent contact with other metal surfaces which could activate the engine electrical system.Place a Do Not Operate tag at the Start/Stop switch location to inform personnel that the equipment is being worked on.
2301A Electric Governor Control
The 2301A Electric Governor Control activates all of the components that are in the electric protection system. The components are activated in the same manner when the nonelectric governor is used. One difference exists in the main circuit. The fuel shutoff solenoid (FSOS) (line 43) is not used.When the electric governor control is used, the engine must run in a normal condition in order for the electric circuit to operate in the manner that is described below.
Current flows from the terminals (TS-28) (line 30) and (TS-31) (line 31), which

Have questions with 105158-2300?





Group cross 105158-2300 ZEXEL

105158-2300  

105158-2301 
9 430 610 122 
 
NOZZLE AND HOLDER ASSY.
9 430 610 140 
0150 
 
NOZZLE AND HOLDER ASSY.
4JG2TC

Isuzu 

9 430 613 711 
0150 
8970886730 
NOZZLE AND HOLDER ASSY.
4JG2TC
9 430 610 497 
88-1130 
 
NOZZLE AND HOLDER ASSY.
4JG2TC

Isuzu 

9 430 613 595 
0150 
8970886740 
NOZZLE AND HOLDER ASSY.
4JG2TC
9 430 610 498 
88-1140 
 
NOZZLE AND HOLDER ASSY.
9 430 610 499 
88-1140 
 
NOZZLE AND HOLDER ASSY.
4JG2

Isuzu 

9 430 613 713 
88-1140 
8970796530 
NOZZLE AND HOLDER ASSY.
4JG2
9 430 610 500 
88-1140 
 
NOZZLE AND HOLDER ASSY.

Isuzu 

9 430 610 501 
88-1140 
8971055440 
NOZZLE AND HOLDER ASSY.
4JG2
9 430 610 502 
88-1090P 
5866363860 
NOZZLE AND HOLDER ASSY.
4EE1-TC
9 430 610 503 
88-1150 
 
NOZZLE AND HOLDER ASSY.
4JG2

Isuzu 

9 430 613 712 
88-1150 
8971256020 
NOZZLE AND HOLDER ASSY.
4JG2
9 430 613 191 
8971256030 
NOZZLE AND HOLDER ASSY.
4JG2

Nissan 

9 430 610 504 
88-1120L 
1660089TA4 
NOZZLE AND HOLDER ASSY.
4JG2

Isuzu 

9 430 613 700 
L88-1120 
8971431960 
NOZZLE AND HOLDER ASSY.
4JG2
9 430 610 505 
88-1120L 
 
NOZZLE AND HOLDER ASSY.
4JG2

Isuzu 

9 430 613 704 
L88-1120 
8971438210 
NOZZLE AND HOLDER ASSY.
4JG2
9 430 610 506 
88-1160 
 
NOZZLE AND HOLDER ASSY.
4JG2T

Isuzu 

9 430 613 703 
88-1160 
8972128410 
NOZZLE AND HOLDER ASSY.
4JG2T
Back to top