Information nozzle and holder assy.
BOSCH
9 430 613 694
9430613694
ZEXEL
105148-1451
1051481451
ISUZU
8971406240
8971406240

Rating:
Compare Prices: .
As an associate, we earn commssions on qualifying purchases through the links below
4PCS Fuel Injector Nozzle 105007-1240 8-97140624-0, Compatible For ISUZU 4JG2 Diesel Engine, 1050071240
JHGTDE 【Compatible Engine】: Compatible For ISUZU 4JG2 Turbo Diesel Engine Systems || 【Pressure Specification】: 2000Bar common rail injection standard, precision-matched OEM flow rate || 【Sealing Upgrade】: Nano-coated needle valve with reinforced polymer seals prevents leakage || 【Durability】: Tungsten carbide nozzle tip resists diesel corrosion, extends service life || 【Installation】: Direct replacement design, no ECM recalibration required
JHGTDE 【Compatible Engine】: Compatible For ISUZU 4JG2 Turbo Diesel Engine Systems || 【Pressure Specification】: 2000Bar common rail injection standard, precision-matched OEM flow rate || 【Sealing Upgrade】: Nano-coated needle valve with reinforced polymer seals prevents leakage || 【Durability】: Tungsten carbide nozzle tip resists diesel corrosion, extends service life || 【Installation】: Direct replacement design, no ECM recalibration required
shsiyayh 1 PCS Fuel Injector Compatible With Isuzu 4JG2 Diesel Engine 8-97140624-0 8971406240
shsiyayh Part Name:Fuel Injector || Part Number:8-97140624-0 8971406240 || APPlication: Compatible with Isuzu 4JG2 Diesel Engine || 1.Please tell us of your engine model or a view of nameplate when order this item to lower the error rate.Thanks. || 2.There are no instructions included in this kit.it is recommended to install professionally.
shsiyayh Part Name:Fuel Injector || Part Number:8-97140624-0 8971406240 || APPlication: Compatible with Isuzu 4JG2 Diesel Engine || 1.Please tell us of your engine model or a view of nameplate when order this item to lower the error rate.Thanks. || 2.There are no instructions included in this kit.it is recommended to install professionally.
You can express buy:
USD 128.69
29-06-2025
29-06-2025
4PCS 4JG2 4JG2T Engine Fuel Injector set 105007-1240 8-97140624-0 For Isuzu Engine TCM KOMATSU HYSTER Forklift Truck Parts New
USD 115
14-06-2025
14-06-2025
4PCS Fuel Injectors 8-97140624-0 105007-1240 for Isuzu 4JG2 Engine Air Filter Assembly 100% New
Images:
USD 24.87
[14-Jun-2025]
USD 41.68
[14-Jun-2025]
USD 115.88
[13-May-2025]
USD 76.81
[14-Jun-2025]
Cross reference number
Zexel num
Bosch num
Firm num
Name
105148-1451
8971406240 ISUZU
NOZZLE AND HOLDER ASSY.
4JG2 K 53KJ NOZZLE & HOLDER ASSY N&NH KCA-P N&NH
4JG2 K 53KJ NOZZLE & HOLDER ASSY N&NH KCA-P N&NH
Information:
At operating temperature, the engine coolant is hot and under pressure. Steam can cause personal injury. Check the coolant level only after the engine has been stopped and the fill cap is cool enough to touch with your bare hand. Remove the fill cap slowly to relieve pressure in the cooling system. Cooling system conditioner contains alkali. Avoid contact with skin and eyes to prevent personal injury.
1. Drain the coolant from the cooling system into a suitable container for storage or disposal. 2. Loosen bolts (1) and (2) on water pump drive (3).3. Remove V-belt (4) from the drive pulley on the water pump and the pulley on the water pump drive.4. Remove two hose clamps (5). Disconnect the hose used between the water pump and the water temperature regulator housing at the water pump.5. Remove four bolts (6) that hold the water pump to the front of the engine. Carefully remove the water pump and two O-ring seals from the front of the engine. The following steps are for the installation of the water pump.6. Check the condition of the two O-ring seals used between the water pump and the cylinder block. If the seals are damaged, use new parts for replacement.7. Install the two O-ring seals in the cover of the water pump. Put the water pump in position on the front of the engine, and install four bolts (6) that hold it.8. Connect the short hose used between the water pump and the water temperature regulator housing to the water pump. Install two clamps (5) that hold the hose in position.9. Put V-belt (4) in position on the water pump drive pulley and the pulley on water pump drive.10. Adjust the tension of water pump drive V-belt (4). Bolt (7) or square hole (8) are used to apply and hold V-belt tension. See the topic "Alternator And Fan Drive Belts, Inspect/Adjust/Replace" in the 3114 & 3116 ATAAC Diesel Truck Engine Operation & Maintenance Manual, Form No. SEBU6723. Also, refer to the "Belt Tension Chart" in the 3114 & 3116 Diesel Truck Engines Specifications module, Form No. SENR6436.11. Fill the cooling system with coolant to the correct level. See the topic "Cooling System" in the 3114 & 3116 ATAAC Diesel Truck Engine Operation & Maintenance Manual, Form No. SEBU6723.Disassemble & Assemble Water Pump
Start By:a. remove water pump 1. Remove two O-ring seals (1) from the rear cover of the water pump. Remove four bolts (2) and the washers. Remove the rear cover and gasket. 2. Put the water pump in a press. Use spacer plates to level the water pump as shown.3. Using a suitable size drive plate from Tool (A) and a press, push the