105148-1051 ZEXEL 9 430 610 401 BOSCH NOZZLE AND HOLDER ASSY. 9430610401 1051481051 8941516151


 

Information nozzle and holder assy.

BOSCH 9 430 610 401 9430610401
ZEXEL 105148-1051 1051481051
ISUZU 8941516151 8941516151
105148-1051 NOZZLE AND HOLDER ASSY.
Rating:
35
Buy NOZZLE AND HOLDER ASSY. 105148-1051 zexel genuine, new aftermarket engine parts with delivery

Include in #2:

104749-6070 as NOZZLE AND HOLDER ASSY

Cross reference number

Zexel num
Bosch num
Firm num
Name
105148-1051 
9 430 610 401 
0002J 
8941516151  ISUZU
NOZZLE AND HOLDER ASSY.
4EC1-T * K




Information:

Start By:a. remove cylinder headb. remove front and rear housingsc. remove rear seal and carrierd. remove pistons and connecting rods 1. Remove bolts (1), remove main bearing caps (2) and remove thrust bearings (3) from the center main. Caps are identified by numbers one through seven. Unmarked caps should be marked by stamping the appropriate number toward the right side of the bottom surface prior to removal. 2. Install two bolts and nylon strap (4) then carefully, remove the crankshaft. The approximate weight of the crankshaft is 129 kg (284 lb).3. Remove the upper portions of the main bearings. The following steps are for the installation of the crankshaft. Be sure main bearing tabs engage the grooves in the block and cap.4. Position the upper portion of the main bearings in the block and the lower main bearing portion in caps (2). Make sure everything is clean and only the bearing face is lubricated with engine oil.5. Position the crankshaft. 6. Install thrust bearings (3).7. Install main bearing caps (2) with the part numbers toward the right hand side of the cylinder block. Take care to insure the caps are numbered one through seven from the front of the engine. Put engine oil or molylube on the bolt threads and the washer face, then install bolts (1). Tighten the bolts on the side where the main bearing tabs are located to a torque of 95 5 N m (70 4 lb ft). Tighten the bolts on the opposite side to a torque of 95 5 N m (70 4 lb ft).8. Put a mark on each bolt head and the bearing caps. Turn the bolts that are opposite the main bearing tabs an additional 90° 5° turn. Then turn the bolts on the side where the main bearing tabs are located an additional 90° 5° turn.
Typical Example9. Use tooling (A) to measure crankshaft end play. The crankshaft end play must be 0.1 to 0.5 mm (.004 to .020 in).End By:a. install pistons and connecting rodsb. install rear seal and carrierc. install rear seal and carrierd. install cylinder head

Have questions with 105148-1051?





Group cross 105148-1051 ZEXEL

Isuzu 

 
8941169341 
NOZZLE AND HOLDER ASSY.
3KC1
9 430 610 061 
0001 
8941169342 
NOZZLE AND HOLDER ASSY.
3KC1
9 430 610 397 
0002 
8941169343 
NOZZLE AND HOLDER ASSY.
3KC1
9 430 610 009 
0010 
 
NOZZLE AND HOLDER ASSY.
9 430 610 398 
0011 
 
NOZZLE AND HOLDER ASSY.

Mitsubishi 

9 430 610 399 
0012 
MD074540 
NOZZLE AND HOLDER ASSY.
4D55

Isuzu 

9 430 613 179 
8941297410 
NOZZLE AND HOLDER ASSY.
4EC1
9 430 613 174 
8941411351 
NOZZLE AND HOLDER ASSY.
4EC1

Mitsubishi 

9 430 610 400 
78-0020 
MD086042 
NOZZLE AND HOLDER ASSY.
4D65

Isuzu 

9 430 613 173 
0000J 
8941516150 
NOZZLE AND HOLDER ASSY.
4EC1-T
105148-1051  
9 430 610 401 
0002J 
8941516151 
NOZZLE AND HOLDER ASSY.
4EC1-T
9 430 610 043 
78-0030 
 
NOZZLE AND HOLDER ASSY.

Mazda 

9 430 613 172 
PN1113H50A 
NOZZLE AND HOLDER ASSY.
PN
9 430 613 423 
78-0031A 
 
NOZZLE AND HOLDER ASSY.

Isuzu 

 
 
NOZZLE AND HOLDER ASSY.
4EC1
 
8944088041 
NOZZLE AND HOLDER ASSY.
4EC1
9 430 610 402 
0041 
8944088042 
NOZZLE AND HOLDER ASSY.
4EC1
9 430 610 403 
0160A 
8944088043 
NOZZLE AND HOLDER ASSY.
4EC1
 
 
NOZZLE AND HOLDER ASSY.
4EC1
 
8944145631 
NOZZLE AND HOLDER ASSY.
4EC1
9 430 610 404 
0041 
8944145632 
NOZZLE AND HOLDER ASSY.
4EC1
9 430 613 424 
 
NOZZLE AND HOLDER ASSY.

Isuzu 

9 430 613 171 
8944145633 
NOZZLE AND HOLDER ASSY.
4EC1

Nissan-Diesel 

9 430 610 405 
0050 
1660043G01 
NOZZLE AND HOLDER ASSY.
AD
Back to top