Information nozzle and holder assy.
BOSCH
9 430 613 962
9430613962
ZEXEL
105118-8303
1051188303
ISUZU
8973829490
8973829490
Rating:
Compare Prices: .
As an associate, we earn commssions on qualifying purchases through the links below
YRGGHUI Diesel Fuel Injector 8-97382949-0 8-97329340-0 105118-8303，Compatible for Isuzu 4KH1 4JH1
YRGGHUI OEM NO.：8-97382949-0 8-97329340-0 105118-8303 || Performance optimization: By adjusting and optimizing the fuel injectors, the performance and fuel economy of the engine can be improved. || Maintenance: Regular inspection and cleaning of fuel injectors are important measures to maintain engine performance, improve fuel efficiency, and optimize engine performance. || Working principle: The electronic fuel injector controls the injection of fuel through a solenoid valve, which is controlled by the engine control unit (ECU). Fuel injectors are divided into two types: mechanical and electronic. Modern cars often use electronic fuel injectors. || Before placing an order, please make sure to confirm whether the product in the link is the same as the old product. Please check the product image, accessories, and item number first. If there are any unclear areas, please provide the product image or item number before placing the order. Thank you!
YRGGHUI OEM NO.：8-97382949-0 8-97329340-0 105118-8303 || Performance optimization: By adjusting and optimizing the fuel injectors, the performance and fuel economy of the engine can be improved. || Maintenance: Regular inspection and cleaning of fuel injectors are important measures to maintain engine performance, improve fuel efficiency, and optimize engine performance. || Working principle: The electronic fuel injector controls the injection of fuel through a solenoid valve, which is controlled by the engine control unit (ECU). Fuel injectors are divided into two types: mechanical and electronic. Modern cars often use electronic fuel injectors. || Before placing an order, please make sure to confirm whether the product in the link is the same as the old product. Please check the product image, accessories, and item number first. If there are any unclear areas, please provide the product image or item number before placing the order. Thank you!
MJUYHT Diesel Fuel Injector 8-97382949-0 8-97329340-0 105118-8303 Compatible for Isuzu 4KH1 4JH1 Automotive System Engine Parts
MJUYHT
MJUYHT
MCLssa Diesel Fuel Injector 8-97382949-0 8-97329340-0 105118-8303 Compatible For ISUZU 4KH1 4JH1, chenliang9494 mall
MCLssa Easy to install, no need for complex operations || High quality fireproof materials achieve maximum durability, stability, and high reliability. || Promote smooth engine operation, balance fuel delivery, reduce overall fuel consumption and harmful emissions. || Stable engine performance: The fuel injector can accurately deliver fuel to the internal combustion of the engine, which is conducive to the full combustion of fuel and stabilizes engine performance. || Diesel Fuel Injector 8-97382949-0 8-97329340-0 105118-8303 Compatible For ISUZU 4KH1 4JH1
MCLssa Easy to install, no need for complex operations || High quality fireproof materials achieve maximum durability, stability, and high reliability. || Promote smooth engine operation, balance fuel delivery, reduce overall fuel consumption and harmful emissions. || Stable engine performance: The fuel injector can accurately deliver fuel to the internal combustion of the engine, which is conducive to the full combustion of fuel and stabilizes engine performance. || Diesel Fuel Injector 8-97382949-0 8-97329340-0 105118-8303 Compatible For ISUZU 4KH1 4JH1
You can express buy:
USD 168
10-11-2022
10-11-2022
Cross reference number
Zexel num
Bosch num
Firm num
Name
105118-8303
8973829490 ISUZU
NOZZLE AND HOLDER ASSY.
4JH1 K 53KW NOZZLE & HOLDER ASSY N&NH
4JH1 K 53KW NOZZLE & HOLDER ASSY N&NH
Information:
350 hp (261 kW) at 2100 rpm and Above (Includes all higher hp [kW] ratings)
Use fuel consumption, distance (odometer) interval or service hours, whichever occurs firts.Daily
Engine Crankcase - Check oil level Leaks and Loose Connections - Inspect Engine Cooling System - Check coolant level Air Cleaner Indicator (If Equipped) - Check Air-to-Air Aftercooler System - CheckPM Level 1
Every 12,500 Miles (20 000 km) or 2500 gal (9500 L) of Fuel or 250 Hours*
Scheduled Oil Sampling (S O S) - Obtain Engine Oil and Filter(s) (NOTE A) - Replace Fuel Filters - Replace final filter/Clean primary filter (if equipped) Cooling System - Test for coolant additive concentration Crankcase Breather - Clean Alternator, Fan and Accessory Drive Belts - Inspect Hoses and Clamps - Inspect/Replace Air-to-Air Aftercooler System - Inspect/Check Fan Drive Bearing - Lubricate Valve Lash (at First PM 1 Interval Only) - Check/AdjustPM Level 2
Every 166,000 Miles (267 000 km) or 33,000 gal (126 000 L) of Fuel or 3,000 Hours*
Performance Analysis Report (PAR) - Obtain Engine - Steam clean Turbocharger - Inspect/Check Engine Mounts - Inspect/Check Vibration Damper - Inspect/Check Air Compressor - Inspect/Check Thermostat - Replace Cooling System - Clean/Flush Water Pump - Rebuild or Exchange2PM Level 3
Every 250,000 Miles (400 000 km) or 50,000 gal (190 000 L) of Fuel or 5,000 Hours*
Fuel Injection Nozzles - Exchange2 Air Compressor - Rebuild or Exchange2 Turbocharger - Rebuild or Exchange2 Valve Lash and Valve Rotators - Check/Adjust Crankshaft Bearings - Inspect/ReplaceOverhaul
Every 500,000 Miles (800 000 km) or 100,000 gal (380 000 L) of Fuel or 10,000 Hours
Fuel Ratio Control - Check/Adjust Governor Set Point and Low Idle - Check/Adjust Top End Overhaul Before Failure Overhaul (In-Frame Overhaul) After Failure Overhaul (Out-of-Frame Overhaul)*First Perform Previous Service Hour ItemsThe distance (odometer) intervals shown on this schedule are based on average fuel rates. This chart assumes 5 mpg (2.1 km/L). Your distance maintenance intervals may need to be adjusted if actual fuel consumption differs from the average fuel consumption Caterpillar considered.Example: Your 3406B rated 425 hp (317 kW) at 2100 rpm is averaging 4.5 mpg (1.9 km/L) due to high load factor operation. The engine consumes 2500 gallons (9500 L) of fuel to travel 11,250 miles (18 000 km). PM Level 1 should be performed at every 11,250 miles (18 000 km) instead of 12,500 miles (20 000 km) shown on the schedule.1Experience has shown that maintenance intervals are most accurately scheduled on the basis of fuel consumed. Rated engine speed and load factor are also important for some components. However, Caterpillar recognizes that the distance (odometer) interval is most commonly used to schedule maintenance for on-highway vehicles.2Replacement with genuine Caterpillar Remanufactured components offers the best value to truck engine customers.NOTE A: Remote mounted or auxiliary filters require additional oil. A 13 quart (12.3 L) supplemental oil filtration system extends the normal oil and filter change interval to 16,500 miles (26 500 km). When changing oil, overfill crankcase by amount needed for auxiliary system (if equipped).To prevent crankshaft and/or bearing
Use fuel consumption, distance (odometer) interval or service hours, whichever occurs firts.Daily
Engine Crankcase - Check oil level Leaks and Loose Connections - Inspect Engine Cooling System - Check coolant level Air Cleaner Indicator (If Equipped) - Check Air-to-Air Aftercooler System - CheckPM Level 1
Every 12,500 Miles (20 000 km) or 2500 gal (9500 L) of Fuel or 250 Hours*
Scheduled Oil Sampling (S O S) - Obtain Engine Oil and Filter(s) (NOTE A) - Replace Fuel Filters - Replace final filter/Clean primary filter (if equipped) Cooling System - Test for coolant additive concentration Crankcase Breather - Clean Alternator, Fan and Accessory Drive Belts - Inspect Hoses and Clamps - Inspect/Replace Air-to-Air Aftercooler System - Inspect/Check Fan Drive Bearing - Lubricate Valve Lash (at First PM 1 Interval Only) - Check/AdjustPM Level 2
Every 166,000 Miles (267 000 km) or 33,000 gal (126 000 L) of Fuel or 3,000 Hours*
Performance Analysis Report (PAR) - Obtain Engine - Steam clean Turbocharger - Inspect/Check Engine Mounts - Inspect/Check Vibration Damper - Inspect/Check Air Compressor - Inspect/Check Thermostat - Replace Cooling System - Clean/Flush Water Pump - Rebuild or Exchange2PM Level 3
Every 250,000 Miles (400 000 km) or 50,000 gal (190 000 L) of Fuel or 5,000 Hours*
Fuel Injection Nozzles - Exchange2 Air Compressor - Rebuild or Exchange2 Turbocharger - Rebuild or Exchange2 Valve Lash and Valve Rotators - Check/Adjust Crankshaft Bearings - Inspect/ReplaceOverhaul
Every 500,000 Miles (800 000 km) or 100,000 gal (380 000 L) of Fuel or 10,000 Hours
Fuel Ratio Control - Check/Adjust Governor Set Point and Low Idle - Check/Adjust Top End Overhaul Before Failure Overhaul (In-Frame Overhaul) After Failure Overhaul (Out-of-Frame Overhaul)*First Perform Previous Service Hour ItemsThe distance (odometer) intervals shown on this schedule are based on average fuel rates. This chart assumes 5 mpg (2.1 km/L). Your distance maintenance intervals may need to be adjusted if actual fuel consumption differs from the average fuel consumption Caterpillar considered.Example: Your 3406B rated 425 hp (317 kW) at 2100 rpm is averaging 4.5 mpg (1.9 km/L) due to high load factor operation. The engine consumes 2500 gallons (9500 L) of fuel to travel 11,250 miles (18 000 km). PM Level 1 should be performed at every 11,250 miles (18 000 km) instead of 12,500 miles (20 000 km) shown on the schedule.1Experience has shown that maintenance intervals are most accurately scheduled on the basis of fuel consumed. Rated engine speed and load factor are also important for some components. However, Caterpillar recognizes that the distance (odometer) interval is most commonly used to schedule maintenance for on-highway vehicles.2Replacement with genuine Caterpillar Remanufactured components offers the best value to truck engine customers.NOTE A: Remote mounted or auxiliary filters require additional oil. A 13 quart (12.3 L) supplemental oil filtration system extends the normal oil and filter change interval to 16,500 miles (26 500 km). When changing oil, overfill crankcase by amount needed for auxiliary system (if equipped).To prevent crankshaft and/or bearing