105118-7781 ZEXEL 9 430 613 744 BOSCH NOZZLE AND HOLDER ASSY. 9430613744 1051187781


 

Information nozzle and holder assy.

BOSCH 9 430 613 744 9430613744
ZEXEL 105118-7781 1051187781
105118-7781 NOZZLE AND HOLDER ASSY.
Rating:
81
Buy NOZZLE AND HOLDER ASSY. 105118-7781 zexel genuine, new aftermarket engine parts with delivery

Cross reference number

Zexel num
Bosch num
Firm num
Name
105118-7781 
105118-7782 
9 430 613 744 
48-4320 37 
   
NOZZLE AND HOLDER ASSY.
*




Information:


Do not engage starter when flywheel is turning.Do not start engine under load.
Above 0°C (32°F)
1. Place the transmission or other power takeoff attachments in NEUTRAL. For air start systems; check the air supply before starting the engine. There must be 690 kPa (100 psi) air pressure available.2. Move governor control lever (throttle) or depress the accelerator to half engine speed position.3. Turn the battery disconnect switch (if equipped) to the ON position. 4. Push the air start knob (1) IN, or ... ... turn the start switch (2) for marine, industrial and generator set engines or ... ... turn the start switch (3) for machines (vehicles) to the START position.
Do not crank the engine for more than 30 seconds. Allow 2 minutes for the starter to cool before cranking again. If oil pressure does not rise within 15 seconds after the engine starts, stop the engine and make necessary corrections.
5. Release the start switch or air start knob when the engine starts.6. Do not apply load to the engine or increase engine speed until oil pressure and all temperature gauges reach operating temperature. Check all gauges during the warm-up period.Below 0°C (32°F)
Ether is poisonous and flammable.Do not store replacement cylinders in living areas or in the operator's compartment.Do not smoke while changing ether cylinders.Use ether only in well ventilated areas.Use it with care to avoid fires.Avoid breathing of the vapors or repeated contact of ether with skin.Do not puncture or burn cylinders.Discard cylinders in a safe place.Keep ether container away from heat, sparks, open flame, or open sunlight. It may explode.Do not store replacement cylinders at temperatures above 49°C (120°F).Do not use cylinders in environments above 93°C (200°F).
1. Depress ether switch and hold for 3 seconds, then release. For air start system; check the air supply before starting the engine. There must be 690 kPa (100 psi) air pressure available.2. Push the air start knob IN or turn the start switch for engines, or turn the start switch for machines (vehicles) to the START position.3. Begin cranking the engine, and depress ether switch and hold for 3 seconds then release. Additional injections of ether may be required to start and/or achieve low idle speed.4. Operate the engine at low speed and/or load until all systems reach operating temperatures. Check all gauges during the warmup period.
Do not use excessive starting fluid during starting or after the engine is running. Do not crank the engine for more than 30 seconds. Allow 2 minutes for the starter motor to cool before cranking again.If oil pressure does not rise within 15 seconds after the engine starts, stop the engine and make necessary corrections.
Turn the battery disconnect switch (if equipped) OFF after the engine is stopped to prevent battery discharge while starter motor is cooling.For starting below -18°C (0°F), use of optional cold weather starting aids are recommended. A coolant heater or extra battery capacity may be required.For temperatures below -23°C (-10°F), consult your Caterpillar dealer or refer to the "Cold Weather Operation

Have questions with 105118-7781?





Group cross 105118-7781 ZEXEL

Nissan-Diesel 

9 430 610 231 
48-4360H7 
16600Z5712 
NOZZLE AND HOLDER ASSY.
FE6TA
9 430 610 232 
48-4370M9 
16600Z6008 
NOZZLE AND HOLDER ASSY.
MD92
9 430 610 233 
48-2230A 
 
NOZZLE AND HOLDER ASSY.
4JA1L

Isuzu 

9 430 613 945 
48-2231A 
8972176420 
NOZZLE AND HOLDER ASSY.
4JA1L
9 430 613 959 
48-2231A 
8973829460 
NOZZLE AND HOLDER ASSY.
4JA1L
9 430 610 234 
48-2240B 
8972207430 
NOZZLE AND HOLDER ASSY.
4JA1L

Nissan 

9 430 610 235 
48-4100G or H 
16600WD001 
NOZZLE AND HOLDER ASSY.
YD1E

Isuzu 

9 430 613 068 
48-2250C 
8971952580 
NOZZLE AND HOLDER ASSY.
P646B

Nissan 

9 430 610 236 
48-4120S or L 
166002W225 
NOZZLE AND HOLDER ASSY.
ZD30DDTI
9 430 610 237 
48-432037 
 
NOZZLE AND HOLDER ASSY.
4M41TC
105118-7781  

105118-7782 
9 430 613 744 
48-4320 37 
 
NOZZLE AND HOLDER ASSY.

Mitsubishi 

9 430 613 988 
ME203537 
NOZZLE AND HOLDER ASSY.
4M41TC
9 430 610 238 
48-4390G or H 
 
NOZZLE AND HOLDER ASSY.

Nissan 

9 430 613 083 
48-4391G or H 
16600WD002 
NOZZLE AND HOLDER ASSY.
YD1E
Back to top