105101-8150 ZEXEL 9 430 611 675 BOSCH NOZZLE AND HOLDER ASSY. 9430611675 1051018150


 

Information nozzle and holder assy.

BOSCH 9 430 611 675 9430611675
ZEXEL 105101-8150 1051018150
105101-8150 NOZZLE AND HOLDER ASSY.
Rating:
66
Buy NOZZLE AND HOLDER ASSY. 105101-8150 zexel genuine, new aftermarket engine parts with delivery

Cross reference number

Zexel num
Bosch num
Firm num
Name
105101-8150 
105101-8151 
9 430 611 675 
31-45006D 
   
NOZZLE AND HOLDER ASSY.
8DC9T * K 53KC N&NH KBDL2,1-S N&NH




Information:

Cautions Regarding Battery* Handle Battery Carefully * Never use flames or allow sparks near the battery. The battery releases flammable hydrogen gas and oxygen gas. These gases can be ignited by flames and cause an explosion.* Do not use the battery when the fluid surface is lower than the minimum level. Using a battery with a low electrolyte level can result in an explosion.* Do not short the battery terminals with a tool or other metal object.* When disconnecting battery cables, always remove the cable from the negative (-) terminal first. When reconnecting cables, attach the cable to the positive (+) terminal first.* Charge the battery in a well-ventilated area, with all filling hole plugs removed.* Make sure the cable clamps are securely installed on the battery terminals. A loose cable clamp can cause sparks that may result in explosion.* Before servicing electrical components or conducting electrical welding, set the battery switch to the [Open/OFF] position or disconnect the cable from the negative (-) battery terminal to cut off the electrical current.* Electrolyte (battery fluid) contains dilute sulfuric acid. Careless handling of the battery can lead to the loss of sight and/or burns. Also, do not swallow electrolyte.* Wear protective goggles and rubber gloves when maintaining and inspecting the battery (when adding water, charging, etc.).* If electrolyte is spilled onto the skin or clothes, immediately wash with lots of clean fresh water and thoroughly clean with soap.* If electrolyte gets into eyes, immediately flush with lots of clean fresh water and seek immediate medical attention.* Should you accidentally swallow electrolyte, gargle with plenty of water, then drink lots of water, and seek immediate medical attention.
Response To Abnormalities* If Engine Overheats, Conduct Heating Operation Before Stopping The Engine If the engine overheats, do not stop the engine immediately. Abruptly stopping an overheated engine may cause the coolant temperature to rise, resulting in seizing of the engine. If the engine overheats, operate the engine at low idling speed (cooling temperature), and stop the engine after the coolant temperature lowers sufficiently.Do not add coolant immediately after stopping the engine. Adding coolant to a hot engine may cause damage to the cylinder heads due to sudden change in temperature. Add coolant after the engine cools to room temperature.* If Engine Stops Due To Abnormality, Exercise Caution When Restarting If the engine stops due to an abnormality, do not restart the engine immediately. If the engine stops with an alarm, check and correct the cause of the problem before restarting. Operating the engine without correcting the problem may result in serious engine problems.* If Oil Pressure Drops, Stop Engine Immediately If the engine oil pressure decreases, stop the engine immediately, and inspect the lubrication system. Operating the engine with low oil pressure may cause seizing of the bearings and other parts.* If Fan Belt Breaks, Stop Engine Immediately If the fan belt breaks, stop the engine immediately. Continued operation of the engine without the fan belt causes coolant to change to steam and

Have questions with 105101-8150?





Group cross 105101-8150 ZEXEL

Dpico 

9 430 612 808 
 
NOZZLE AND HOLDER ASSY.
EF750TCI
9 430 612 807 
30-4800 
 
NOZZLE AND HOLDER ASSY.
8DC9T2

Hino 

9 430 611 670 
31-7363I 
236002950A 
NOZZLE AND HOLDER ASSY.
K13D
9 430 611 671 
30-3581T 
236002910A 
NOZZLE AND HOLDER ASSY.
F20C
9 430 611 672 
30-3670A2 
236002960A 
NOZZLE AND HOLDER ASSY.
K13C-TM
9 430 611 673 
30-3670A3 
236002961A 
NOZZLE AND HOLDER ASSY.
K13C-TM
9 430 611 674 
30-3670A4 
236002962A 
NOZZLE AND HOLDER ASSY.
K13C-TM
9 430 612 754 
30-3670296 
236002962B 
NOZZLE AND HOLDER ASSY.
K13C-TM
105101-8150  

105101-8151 
9 430 611 675 
31-45006D 
 
NOZZLE AND HOLDER ASSY.
8DC9T

Mitsubishi 

9 430 613 775 
30-49806D 
ME098757 
NOZZLE AND HOLDER ASSY.
8DC9T

Hino 

9 430 611 676 
30-3700 
236002980A 
NOZZLE AND HOLDER ASSY.
J-2

Nissan-Diesel 

9 430 611 677 
30-4810E7 
16600Z5669 
NOZZLE AND HOLDER ASSY.
FE6A

Hino 

9 430 612 827 
30-353180 
236003080A 
NOZZLE AND HOLDER ASSY.
YJ60
9 430 612 826 
30-3531308 
236003080B 
NOZZLE AND HOLDER ASSY.
YJ60
9 430 611 678 
30-3670E 
236002990A 
NOZZLE AND HOLDER ASSY.
K-4
9 430 611 679 
30-3670E1 
236002991A 
NOZZLE AND HOLDER ASSY.
YJ39
Back to top