105101-7660 ZEXEL 9 430 613 009 BOSCH NOZZLE AND HOLDER ASSY. 9430613009 1051017660


 

Information nozzle and holder assy.

BOSCH 9 430 613 009 9430613009
ZEXEL 105101-7660 1051017660
105101-7660 NOZZLE AND HOLDER ASSY.
Rating:
74
Buy NOZZLE AND HOLDER ASSY. 105101-7660 zexel genuine, new aftermarket engine parts with delivery

Include in #1:

106871-4150 as NOZZLE AND HOLDER ASSY

Cross reference number

Zexel num
Bosch num
Firm num
Name
105101-7660 
9 430 613 009 
31-7230S 
   
NOZZLE AND HOLDER ASSY.
F17C K




Information:


Unsolder the leads quickly to prevent heat from damaging the diodes.
(b) Remove the rectifiers mounting screws, then remove the rectifier.
Removing statorInspection
Key Points For Inspection(1) Inspection Rectifier
With each diode, measure the resistance between the diode terminal and the heat sink. Measure the resistance with the tester's (+) probe applied to the diode terminal and with the tester's (-) probe applied to the diode terminal. If the resistance is infinite in both cases, there is an open circuit. If the resistance is close to zero in both cases, there is a short circuit. An open circuit or short circuit indicates a diode fault. Replace the rectifiers if any diode is faulty.Next, measure the resistance between the terminals of the leads that connect the rectifier to the stator coil for each of the diodes. If any measurement reveals an open circuit (infinite resistance) or a short circuit (near-zero resistance), replace the rectifier.
Inspecting rectifier(2) Inspecting Field Coil
(a) Check whether continuity exists between the rotor's slip rings. If continuity does not exist, the field coil is open-circuited and the rotor must be replaced.
Field coil continuity test(b) Check whether continuity exists between each slip ring and the rotor shaft (or core). If continuity exists, the field coil is grounded and the rotor must be replaced.
Field coil ground test(3) Inspecting Stator Coils
(a) Check whether continuity exists between the leads at the ends of each stator coil. If continuity does not exist between any coil's leads, there is an open circuit and the stator must be replaced.
Stator coil continuity test(b) Check whether continuity exists between each stator coil lead and the stator core. If continuity exists, the stator coil is grounded and the stator must be replaced.
Stator coil ground test(4) Inspecting Brushes
(a) Replace the brush if it is worn down to the wear limit line.
Inspecting Brush(b) Disconnect the brush lead wires at the soldered sections to remove the brushes and springs.
Removing brushes and springs(c) To install new brushes, press them into the brush holders as shown in the diagram, then solder the lead wires.
Installing brushesAssembly
Follow the reverse of disassembly and use the procedure below:(1) The rear bearing has a groove for the snap ring. Install the snap ring in this groove. Make sure its tab is in the deep portion of the groove.(2) When installing the new rear bearing, place it in position with the side that has a groove toward the slip rings of the rotor.(3) To install the rear bearing in the rear bracket, heat the rear bracket.(4) Before installing the rotor in the rear bracket, insert a wire-shaped tooling into the hole in the rear bracket to lift the brushes of the slip rings. Remove the tooling after the rotor has been installed in position.
Assembling alternatorInstallation
Perform installation by following the removal sequence in reverse. Key Points For Installation(1) Install the fan belt on the alternator and mount the alternator on the engine. Temporarily tighten all the bolts.(2) Insert a bar between the alternator and crankcase. Using the bar as leverage, move the alternator

Have questions with 105101-7660?





Group cross 105101-7660 ZEXEL

Mitsubishi 

9 430 611 621 
30-4451 
ME161080 
NOZZLE AND HOLDER ASSY.
8M20
9 430 611 622 
30-4451 
ME3H6015 
NOZZLE AND HOLDER ASSY.
8M20

Isuzu 

9 430 611 623 
30-3540R 
1153003140 
NOZZLE AND HOLDER ASSY.
10PE1

Nissan-Diesel 

9 430 613 010 
16600Z5610 
NOZZLE AND HOLDER ASSY.
FE6TA
9 430 611 624 
30-45109 
 
NOZZLE AND HOLDER ASSY.
8DC11

Mitsubishi 

9 430 613 762 
30-50009 
ME093276 
NOZZLE AND HOLDER ASSY.
8DC11

Hyundai 

9 430 613 008 
 
NOZZLE AND HOLDER ASSY.
P
105101-7660  
9 430 613 009 
31-7230S 
 
NOZZLE AND HOLDER ASSY.
F17C

Hyundai 

9 430 613 007 
30-4510A 
 
NOZZLE AND HOLDER ASSY.
8DC11

Dpico 

9 430 613 006 
31-4530J 
 
NOZZLE AND HOLDER ASSY.
Q-I
9 430 611 625 
30-4580Z 
 
NOZZLE AND HOLDER ASSY.
6D22T3

Mitsubishi 

9 430 613 899 
30-4581Z 
ME150862 
NOZZLE AND HOLDER ASSY.
6D22T3
Back to top