105101-2020 ZEXEL 9 430 611 222 BOSCH NOZZLE AND HOLDER ASSY. 9430611222 1051012020 1470378


 

Information nozzle and holder assy.

BOSCH 9 430 611 222 9430611222
ZEXEL 105101-2020 1051012020
  1470378
105101-2020 NOZZLE AND HOLDER ASSY.
Rating:
39
Buy NOZZLE AND HOLDER ASSY. 105101-2020 zexel genuine, new aftermarket engine parts with delivery

Cross reference number

Zexel num
Bosch num
Firm num
Name
105101-2020 
9 430 611 222 
31-1660 
1470378   
NOZZLE AND HOLDER ASSY.
MDJE *




Information:


Table 4
Storage Temperature Expected DEF Life
Below 25° C (77° F) 18 months
25° C (77° F) to 30° C (86° F) 12 months
30° C (86° F) to 35° C (95° F) 6 months
Above 35° C (95° F) test quality before use Refer to "ISO 22241" document series for more information about DEF quality control.Note: Dispose of all fluids according to applicable regulations and mandates.DEF/Urea Solution Recommendations for Marine Engines
The US has adopted/approved NOx Emissions Control Area (ECA) regulations. Per ECAs, vessels that are 2016 and later models, or vessels that are modified to 2016 models, are required to meet Tier III NOx standards. These engines may require the use of Diesel Exhaust Fluid (DEF) and other urea solutions for engines equipped with Selective Catalytic Reduction (SCR) systems. If required, Cat marine engines are designed to operate on DEF of urea concentrations of 32.5 percent (by weight) or 40 percent (by weight). The crystallization temperature of 40 percent urea solution is 0° C (32° F). If urea solution ambient temperatures are routinely below 5° C (41° F) and supplemental heat is not applied to urea storage, then 32.5 percent solution should be used and maintained at a temperature above −0° C (14° F). Urea solutions should be maintained above the specified freezing temperature. Consult the urea supplier and follow the guidelines provided in this article for handling and recommendations.Vessels that are traveling internationally and have on/off NOx controls that allow the vessels to meet ECA regulations must enable NOx controls prior to entering the ECA. For US flagged vessels, the SCR must be activated and deactivated automatically based on input from the Global Positioning System. For US flagged vessels, on/off NOx controls are allowed on engines > 30 liters/cylinder and are not allowed on engines < 30 liters/cylinder unless installed on a vessel with propulsion engines >30 liters/cylinder. Otherwise the NOx control systems on Category 1 and 2 engines must always be on. Foreign destinations should be reviewed for supply of ULSD fuel and DEF prior to departure. Exemptions for ULSD or DEF use due to fluid unavailability per 40 CFR part 1042.650(a) by US flagged vessels operating outside of US waters may be requested from the US Environmental Protection Agency (EPA). The EPA can be contacted at the following address:complianceinfo@epa.gov
When used in marine engines, DEF of 32.5 percent urea concentration must meet all the guidelines and quality recommendations given in this Chapter.When used in marine engines, urea solution of 40 percent urea concentration must follow all the DEF guidelines and quality recommendations given in this chapter and must meet the characteristics listed in Table 5 for 40 percent concentration. The supplier should provide documentation to prove that the urea solution is compliant with the characteristics published in Table 5.Refer to your engine Operation and Maintenance Manual to determine the concentration of urea solution allowed in your engine.
Cat does not warrant the quality or performance of non-Cat fluids and greases.
General Characteristics of DEF
For detailed information on the requirements and

Have questions with 105101-2020?





Group cross 105101-2020 ZEXEL

9 430 611 221 
31-2590 
1432700301 
NOZZLE AND HOLDER ASSY.
45F

Isuzu 

9 430 610 093 
31-2600 
9153001842 
NOZZLE AND HOLDER ASSY.
DA640
105101-2020  
9 430 611 222 
31-1660 
1470378 
NOZZLE AND HOLDER ASSY.
MDJE
9 430 611 223 
31-3350A 
41632690A 

6L16
9 430 610 012 
31-2220 
1622703300 
NOZZLE AND HOLDER ASSY.
16B
9 430 610 103 
31-1680 
 
NOZZLE AND HOLDER ASSY.
MDJE
9 430 611 224 
31-3570 
100219140 
NOZZLE AND HOLDER ASSY.
S16V
9 430 611 225 
31-1120A 
100219082 

S617
9 430 611 226 
31-1690 
51032251A 
NOZZLE AND HOLDER ASSY.
6L16
9 430 611 227 
31-1700 
100219100 
NOZZLE AND HOLDER ASSY.
S617
Back to top