105100-7290 ZEXEL 9 430 611 100 BOSCH NOZZLE AND HOLDER ASSY. 9430611100 1051007290 236001750a


 

Information nozzle and holder assy.

BOSCH 9 430 611 100 9430611100
ZEXEL 105100-7290 1051007290
HINO 236001750A 236001750a
105100-7290 NOZZLE AND HOLDER ASSY.
Rating:
76
Buy NOZZLE AND HOLDER ASSY. 105100-7290 zexel genuine, new aftermarket engine parts with delivery

Cross reference number

Zexel num
Bosch num
Firm num
Name
105100-7290 
105100-7350 
9 430 611 100 
31-7190 
236001750A  HINO
NOZZLE AND HOLDER ASSY.
K13C * K 53KC N&NH KBDL2,1-S N&NH




Information:


Table 1
S O S Oil Sampling Interval for Engine crankcase
Recommended Interval (1)(2) Oil Type
Every 250 Service Hours Cat DEO
Cat DEO-ULS
(1) Severe applications may require a more frequent oil sampling interval.
(2) Under certain conditions, the Cat dealer or the Operation and Maintenance Manual may allow a longer interval between oil samplings.Note: Refer to the Operation and Maintenance Manual for your engine for recommended oil drain intervals.Consult your Cat dealer for complete information and assistance in order to establish an S O S Services program for your engine.More Frequent S O S Sampling Improves Life Cycle Management
Traditionally, the suggested S O S sampling intervals for diesel engines have been at 250 hours. However in severe applications, more frequent oil sampling is recommended. Severe service for lubricated compartments occurs at high loads, in high temperatures, and in dusty conditions. If any of these conditions or other severe service indicators exist, sample the engine oil at 125 hour intervals. These additional samples will increase the chance of detecting a potential failure.Determining Optimum Oil Change Intervals
Sampling the engine oil at every 125 hours provides information for oil condition and for oil performance. This information is used to determine the optimum usable life of a particular oil. Also, more points of data will allow closer monitoring of component wear rates. Close monitoring also allows you to obtain the maximum use of the oil. For detailed information on optimizing oil change intervals, consult your Cat dealer.This Special Publication does not address recommended oil drain intervals. Refer to your engine Operation and Maintenance Manual, and consult your Cat dealer for additional guidance, including but not limited to guidance on establishing optimized and/or acceptable oil drain intervals.To reduce the potential risk of failures associated with extended oil drain periods, Caterpillar recommends that oil drain intervals only be extended based on oil analysis, and subsequent system inspections. Oil analysis alone does not provide an indication of the rate of formation of lacquer, varnish and/or other deposits on surfaces. The only accurate way to evaluate specific oil performance in a specific system using extended oil drain periods is to observe the effects on the system components. Making these observations involves tear-down inspections of systems that have run to the normal overhaul period while using extended oil drain intervals. Following this recommendation will help ensure that excessive component wear does not take place in a given application.Note: The use of Cat S O S Services oil analysis helps environmental sustainability as the best way to optimize oil life. S O S Services will help engines reach expected life. Consult your Cat dealer regarding the testing required to establish a safe, optimized oil drain interval.Standard oil drain intervals as published in engine Operation and Maintenance Manual are for typical applications:
Using recommended oils
Using good fuel
Using recommended filters
Using industry standard good maintenance practices
Following maintenance intervals as published in engine Operation and Maintenance ManualMore severe applications may require shortened oil drain intervals, while less severe applications may allow for longer than standard oil drain intervals. High

Have questions with 105100-7290?





Group cross 105100-7290 ZEXEL

Nissan-Diesel 

9 430 611 088 
31-4630D 
1660096516 
NOZZLE AND HOLDER ASSY.
PE6
9 430 611 089 
31-4790B5 
1660097063 
NOZZLE AND HOLDER ASSY.
RF8

Isuzu 

9 430 611 090 
31-4870 
1153001790 
NOZZLE AND HOLDER ASSY.
6SD1-T
9 430 611 091 
31-48012N 
1153001791 
NOZZLE AND HOLDER ASSY.
6SD1-T

Mitsubishi 

9 430 611 092 
31-4530B 
 
NOZZLE AND HOLDER ASSY.
6D22T

Hyundai 

9 430 611 092 
31-4530B 
3380083600 
NOZZLE AND HOLDER ASSY.
6D22T

Nissan-Diesel 

9 430 611 093 
31-4790B6 
1660097064 
NOZZLE AND HOLDER ASSY.
RF8

Isuzu 

9 430 611 094 
30-3170 
1153001640 
NOZZLE AND HOLDER ASSY.
6BG1

Hino 

9 430 611 095 
31-4890 
236001740A 
NOZZLE AND HOLDER ASSY.
EP-2
9 430 611 096 
31-4890B 
236001741A 
NOZZLE AND HOLDER ASSY.
EP-2

Nissan-Diesel 

9 430 611 097 
31-4790B7 
1660097066 
NOZZLE AND HOLDER ASSY.
RE8

Isuzu 

9 430 611 098 
30-3170A 
1153001910 
NOZZLE AND HOLDER ASSY.
6BG1
9 430 611 099 
30-32312G 
1153001911 
NOZZLE AND HOLDER ASSY.
6BG1

Hino 

105100-7290  

105100-7350 
9 430 611 100 
31-7190 
236001750A 
NOZZLE AND HOLDER ASSY.
K13C
Back to top