105100-6960 ZEXEL 9 430 611 059 BOSCH NOZZLE AND HOLDER ASSY. 9430611059 1051006960 1660095010


 

Information nozzle and holder assy.

BOSCH 9 430 611 059 9430611059
ZEXEL 105100-6960 1051006960
NISSAN-DIESEL 1660095010 1660095010
105100-6960 NOZZLE AND HOLDER ASSY.
Rating:
26
Buy NOZZLE AND HOLDER ASSY. 105100-6960 zexel genuine, new aftermarket engine parts with delivery

Include in #1:

101691-9551 as NOZZLE AND HOLDER ASSY

Cross reference number

Zexel num
Bosch num
Firm num
Name
105100-6960 
9 430 611 059 
31-4620N 
1660095010  NISSAN-DIESEL
NOZZLE AND HOLDER ASSY.
NE6 K 53KB NOZZLE & HOLDER ASSY N&NH KBL-S N&NH




Information:


Recommended engine warm-up procedure must be followed. Refer to the engine Operation and Maintenance Manual. Also refer to the relevant “Lubricant Viscosities for Ambient Temperatures” table footnote in this Special Publication.
Excessive engine idling time can contribute to excessive water in the crankcase oil, causing corrosion, sludge, and other problems. Excessive engine idling time can also lead to injector fouling, piston and combustion chamber deposits, corrosive damage, and increased oil consumption.
For proper selection of oil viscosity grade and oil type and/or specification, refer to this Special Publication, "Lubricant Specifications" section.Also, refer to this Special Publication, "Lubricant Viscosities" article.
Not following the recommendations found in the “Lubricant Viscosities for Ambient Temperatures” table and associated footnotes can lead to reduced performance and engine failure.
Do NOT use only the oil viscosities when determining the recommended oil for an engine compartment. The oil type (performance requirements) MUST also be used.
For easier cold weather starting, make sure that all of the components of the engine electrical system are properly maintained. All electrical wiring and connections should be free of the following: fraying, damaged insulation and corrosion. Batteries should be kept fully charged and warm. The batteries and the battery cables must be sized properly for the application.Various starting aids are available in order to assist with cold engine starts in low temperature conditions. Follow the recommendations that are provided by the manufacturer of the starting aid. Refer to the foreword section of this Special Publication, "Aftermarket Products and Warranty".For additional information concerning cold-weather operation, refer to this Special Publication, "Fuel Specifications" section. Also refer to this Special Publication, "Cooling System Specifications" section.Before attempting to start the engine, make sure that the oil in the engine is fluid enough to flow. Check the oil by removing the dipstick. If the oil will drip from the dipstick, then the oil should be fluid enough to allow the engine to start. Do not use oil that has been diluted with kerosene. Kerosene will evaporate in the engine. and cause the oil to thicken. Kerosene will cause swelling and softening of the silicone seals. Kerosene will dilute the oil additives. Dilution of the oil additives will reduce the performance, and reduce the engine protection that the additives provide.If the viscosity of the oil is changed for colder weather, also change the filter element. If the filter is not changed, the filter element and the filter housing can become a solid mass. After you change the oil, operate the engine in order to circulate the thinner oil.When you start a cold-soaked engine or when you operate an engine in ambient temperatures that are below −18°C (0°F), use base oils that can flow in low temperatures. These multigrade oils have lubricant viscosity grade of

Have questions with 105100-6960?





Group cross 105100-6960 ZEXEL

Nissan-Diesel 

 
1660090065 
NOZZLE AND HOLDER ASSY.
FD33

Isuzu 

9 430 611 050 
30-3000 
1153001690 
NOZZLE AND HOLDER ASSY.
6BG1
9 430 611 051 
30-3201 
1153001691 
NOZZLE AND HOLDER ASSY.
6BG1
9 430 611 052 
30-3010 
1153001700 
NOZZLE AND HOLDER ASSY.
6BD1-T
9 430 611 053 
30-3201D 
1153001701 
NOZZLE AND HOLDER ASSY.
6BD1-T
9 430 611 054 
30-3020 
1153001710 
NOZZLE AND HOLDER ASSY.
6BG1
9 430 611 055 
30-32012C 
1153001711 
NOZZLE AND HOLDER ASSY.
6BG1
9 430 611 056 
30-3030 
1153001680 
NOZZLE AND HOLDER ASSY.
6SA1
9 430 612 983 
30-32012E 
1153001681 
NOZZLE AND HOLDER ASSY.
6SA1
9 430 611 057 
31-4770A 
1153001660 
NOZZLE AND HOLDER ASSY.
6SA1PA
9 430 611 058 
31-47713 
1153001661 
NOZZLE AND HOLDER ASSY.
6SA1PA

Nissan-Diesel 

105100-6960  
9 430 611 059 
31-4620N 
1660095010 
NOZZLE AND HOLDER ASSY.
NE6
9 430 611 060 
31-4620T 
1660095011 
NOZZLE AND HOLDER ASSY.
NE6T

Isuzu 

9 430 611 061 
30-3040 
1153001720 
NOZZLE AND HOLDER ASSY.
6SA1-T
9 430 612 982 
30-3201N1 
1153001721 
NOZZLE AND HOLDER ASSY.
6SA1-T
9 430 611 062 
31-4820 
1153001590 
NOZZLE AND HOLDER ASSY.
6RB1-TC
9 430 611 063 
30-4271E 
1153001591 
NOZZLE AND HOLDER ASSY.
6RB1-TC
Back to top