105100-4481 ZEXEL 9 430 610 780 BOSCH NOZZLE AND HOLDER ASSY. 9430610780 1051004481


 

Information nozzle and holder assy.

BOSCH 9 430 610 780 9430610780
ZEXEL 105100-4481 1051004481
105100-4481 NOZZLE AND HOLDER ASSY.
Rating:
64
Buy NOZZLE AND HOLDER ASSY. 105100-4481 zexel genuine, new aftermarket engine parts with delivery

Cross reference number

Zexel num
Bosch num
Firm num
Name
105100-4481 
105100-4482 
9 430 610 780 
31-3522N 
   
NOZZLE AND HOLDER ASSY.
10DC8 * K 53KB N&NH KBL-S N&NH




Information:

Start By:a. disassemble governorb. remove fuel injection pumps 1. Remove the six lifters from the fuel pump housing.2. Remove rack (1) and camshaft (2) from the fuel pump housing. If necessary use a soft hammer to push the camshaft out the governor end. 3. Use tooling (A) and remove the three camshaft bearings from the fuel pump housing. 4. Remove rack bearing (4) and the other rack bearing from the fuel pump housing.5. Remove dowel (3) from the fuel pump housing. 6. Remove bolts (6), cover (5) and the gasket from the fuel pump housing.Assemble Fuel Injection Pump Housing
1. Install gasket (7) and cover (5) on the side of the fuel pump housing. 2. Use tooling (B) and install (D) shaped rack bearing into the automatic timing advance side of the fuel pump housing 87.0 0.5 mm (3.42 .02 in) from outside surface (X).3. The inside flat side diameter after assembly must be 11.178 0.050 mm (.440 .002 in) and the inside large diameter must be 12.767 0.058 mm (.503 .002 in). 4. Install dowel (3) in the fuel pump housing 6.0 0.5 mm (.24 .02 in) above the outside surface.5. Use tool group (C) and install the rack bearing into the fuel pump housing 7.16 0.13 mm (.282 .005 in) below the outside surface of the pump housing.6. The inside diameter of the bearing after assembly must be 12.746 0.045 mm (.502 .002 in). 7. Use tool group (A) and install the three camshaft bearings in the fuel pump housing with the oil holes in the bearings 30° 3° from the horizontal center line toward the plugged holes in the fuel pump housing.8. The inside diameter of all three bearings after assembly must be 68.339 0.038 mm (2.6905 .0015 in). 9. Make sure bearing (8) on automatic timing advance side is installed 1.0 0.5 mm (.04 .02 in) below surface (Y).10. Make sure middle bearing (9) is 218 0.3 mm (8.6 .01 in) below surface (Y). 11. Make sure bearing (10) governor side 1.00 0.25 mm (.04 .01 in) below the outside surface.12. Remove the plugs from the side of the fuel pump housing. The oil holes in the bearings must be in alignment with holes (11) in the fuel pump housing. If the bearings are not in alignment, remove them and install again. 13. Make an alignment of rack (1) and install it in the fuel pump housing.14. Install camshaft (2) in the fuel pump housing as shown.15. Install the six lifters in the fuel pump housing. Make sure the pins in the lifter are on the same side as the dowels in the fuel pump housing.End By:a. install fuel injection pumpsb. assemble governor

Have questions with 105100-4481?





Group cross 105100-4481 ZEXEL

9 430 610 771 
31-3560 
 
NOZZLE AND HOLDER ASSY.
12V150Z
9 430 610 772 
31-6110 
 
NOZZLE AND HOLDER ASSY.
150Z
9 430 610 773 
31-6110A 
 
NOZZLE AND HOLDER ASSY.
150Z
9 430 610 774 
31-5330 
 
NOZZLE AND HOLDER ASSY.
6130Z

Komatsu 

9 430 610 775 
31-4360 
6137113100 
NOZZLE AND HOLDER ASSY.
D105

Hino 

9 430 610 776 
31-5300A 
236001025A 
NOZZLE AND HOLDER ASSY.
EK100

Mitsubishi 

9 430 610 777 
31-4300C 
3129653401 
NOZZLE AND HOLDER ASSY.
8DC8

Komatsu 

9 430 610 778 
31-4360A 
6136113100 
NOZZLE AND HOLDER ASSY.
S6D105
9 430 610 779 
31-3521N 
 
NOZZLE AND HOLDER ASSY.
105100-4481  

105100-4482 
9 430 610 780 
31-3522N 
 
NOZZLE AND HOLDER ASSY.
10DC8

Mitsubishi 

9 430 613 939 
30-4990N 
3196169050 
NOZZLE AND HOLDER ASSY.
10DC8

Komatsu 

9 430 610 781 
31-3510A 
6131123700 
NOZZLE AND HOLDER ASSY.
S4D105
Back to top