Information nozzle-holder
BOSCH
9 430 615 247
9430615247
ZEXEL
105048-4060
1050484060
NISSAN-DIESEL
1661019D01
1661019d01
Rating:
Scheme ###:
| 8. | [1] | 150562-4300 | COMPRESSION SPRING |
| 10. | [1] | 150560-0400 | SLOTTED WASHER |
| 16. | [2] | 150508-5900 | BEARING PIN |
| 18. | [1] | 150524-4200 | SPACER BUSHING |
| 22. | [1] | 150655-0000 | NOZZLE-RETAINING NUT |
| 800S/1. | [1] | 150591-1000 | SHIM D7.2&3.6T0.10 |
| 800S/1. | [1] | 150591-2000 | SHIM D7.2&3.6T0.20 |
| 800S/1. | [1] | 150591-3000 | SHIM D7.2&3.6T0.30 |
| 800S/1. | [1] | 150591-4000 | SHIM D7.2&3.6T0.40 |
| 800S/1. | [1] | 150591-5000 | SHIM D7.2&3.6T0.50 |
| 800S/1. | [1] | 150591-5100 | SHIM D7.2&3.6T0.51 |
| 800S/1. | [1] | 150591-5200 | SHIM D7.2&3.6T0.52 |
| 800S/1. | [1] | 150591-5300 | SHIM D7.2&3.6T0.53 |
| 800S/1. | [1] | 150591-5400 | SHIM D7.2&3.6T0.54 |
| 800S/1. | [1] | 150591-5500 | SHIM D7.2&3.6T0.55 |
| 800S/1. | [1] | 150591-5600 | SHIM D7.2&3.6T0.56 |
| 800S/1. | [1] | 150591-5700 | SHIM D7.2&3.6T0.57 |
| 800S/1. | [1] | 150591-5800 | SHIM D7.2&3.6T0.58 |
| 800S/1. | [1] | 150591-5900 | SHIM D7.2&3.6T0.59 |
Include in #1:
101401-9710
as NOZZLE-HOLDER
Cross reference number
Zexel num
Bosch num
Firm num
Name
105048-4060
9 430 615 247
1661019D01 NISSAN-DIESEL
NOZZLE-HOLDER
K 53LZ NOZZLE HOLDER NH NH
K 53LZ NOZZLE HOLDER NH NH
Information:
Start By:a. remove timing gear cover
Do not disconnect the air line from the air compressor governor until the air pressure is zero.
1. Loosen the bleed valves, and release the air pressure in the air tank. 2. Disconnect the lines from air compressor (1), and remove the air compressor. 3. Remove sleeve (2) from air compressor drive gear (3). 4. Remove the nut and washer that holds the air compressor drive gear to the air compressor. Use tooling (A) to remove air compressor drive gear (3) from the air compressor. 5. Remove nuts (4) and plate (5). Remove gear assembly (6) from the shaft. 6. If damaged, remove bearing (7) from gear assembly (6) with tooling (B) and a press. 7. Remove three nuts (8) and the washers from the adapter assembly studs.
Typical Example8. Remove adapter assembly (9) from the timing gear plate. 9. Remove shaft (10), O-ring seal (11) and sleeve (12) from the adapter assembly.Install Air Compressor And Accessory Drive
1. Install sleeve (12) into the adapter assembly.2. Install shaft (10) and O-ring seal (11) on the adapter assembly. 3. Put adapter assembly (9) in position on the timing gear plate. Fasten it with the three nuts and washers. 4. Install the bearing in gear assembly (6) with tooling (A) and a press. Install the bearing until it is 1.5 0.5 mm (.06 .02 in.) below the surface of the gear as shown. 5. Put gear assembly (6) in position on the shaft.6. Put plate (5) in position, and install three nuts (4) to hold it. 7. Put air compressor drive gear (3) in position on the air compressor shaft, and install the washer and nut (13). Tighten the nut to a torque of 200 25 N m (150 18 lb.ft.). Tap the gear with a hammer and tighten nut (13) again to a torque of 200 25 N m (150 18 lb.ft.). 8. Install sleeve (2) on gear (3). 9. Put a gasket in position on air compressor (1) and install the air compressor on the timing cover plate.End By:a. install timing gear cover
Do not disconnect the air line from the air compressor governor until the air pressure is zero.
1. Loosen the bleed valves, and release the air pressure in the air tank. 2. Disconnect the lines from air compressor (1), and remove the air compressor. 3. Remove sleeve (2) from air compressor drive gear (3). 4. Remove the nut and washer that holds the air compressor drive gear to the air compressor. Use tooling (A) to remove air compressor drive gear (3) from the air compressor. 5. Remove nuts (4) and plate (5). Remove gear assembly (6) from the shaft. 6. If damaged, remove bearing (7) from gear assembly (6) with tooling (B) and a press. 7. Remove three nuts (8) and the washers from the adapter assembly studs.
Typical Example8. Remove adapter assembly (9) from the timing gear plate. 9. Remove shaft (10), O-ring seal (11) and sleeve (12) from the adapter assembly.Install Air Compressor And Accessory Drive
1. Install sleeve (12) into the adapter assembly.2. Install shaft (10) and O-ring seal (11) on the adapter assembly. 3. Put adapter assembly (9) in position on the timing gear plate. Fasten it with the three nuts and washers. 4. Install the bearing in gear assembly (6) with tooling (A) and a press. Install the bearing until it is 1.5 0.5 mm (.06 .02 in.) below the surface of the gear as shown. 5. Put gear assembly (6) in position on the shaft.6. Put plate (5) in position, and install three nuts (4) to hold it. 7. Put air compressor drive gear (3) in position on the air compressor shaft, and install the washer and nut (13). Tighten the nut to a torque of 200 25 N m (150 18 lb.ft.). Tap the gear with a hammer and tighten nut (13) again to a torque of 200 25 N m (150 18 lb.ft.). 8. Install sleeve (2) on gear (3). 9. Put a gasket in position on air compressor (1) and install the air compressor on the timing cover plate.End By:a. install timing gear cover
Have questions with 105048-4060?
Group cross 105048-4060 ZEXEL
Nissan-Diesel
Nissan
Nissan-Diesel
Mazda
Nissan-Diesel
105048-4060
9 430 615 247
1661019D01
NOZZLE-HOLDER