105048-3980 ZEXEL 9 430 615 960 BOSCH NOZZLE-HOLDER 9430615960 1050483980 16610z5565


 

Information nozzle-holder

BOSCH 9 430 615 960 9430615960
ZEXEL 105048-3980 1050483980
NISSAN-DIESEL 16610Z5565 16610z5565
105048-3980 NOZZLE-HOLDER
Rating:
27
Buy NOZZLE-HOLDER 105048-3980 zexel genuine, new aftermarket engine parts with delivery

Cross reference number

Zexel num
Bosch num
Firm num
Name
105048-3980 
105048-3970 
9 430 615 960 
16610Z5565  NISSAN-DIESEL
NOZZLE-HOLDER
* K 53LZ NH NH




Information:

2. Remove bolts (1) from the alternator bracket.3. Remove the bolts that hold plate (3), and remove the plate.4. Disconnect water line (2) from the air compressor. Turn the water line tee toward the lifting bracket in order to provide clearance to remove the head bolt. 5. Remove bolts (4) and (5) that hold the cylinder head assembly to the cylinder block.6. Fasten a hoist, and remove the cylinder head assembly. The weight is approximately 135 kg (300 lb.).
Do not put the cylinder head assembly down on a flat surface. This can cause damage to the fuel injection valves.
7. Remove the gasket, seals (6) and O-ring seals (7) from the spacer plate. The following steps are for installation of the cylinder head. Be sure a new gasket has been installed between the spacer plate and the cylinder block. See Remove And Install Spacer Plate.8. Thoroughly clean the spacer plate and the bottom surface of the cylinder head assembly. Install a new head gasket, new seals (6) and two O-ring seals (7).9. Fasten a hoist, and put the cylinder head assembly in position on the cylinder block. 10. Put Loctite Nickel Anti-Seize on the threads of the cylinder head bolts. Install the cylinder head bolts and washers. Tighten the bolts in sequence shown.a. Tighten bolts 1 through 14 in number sequence to a torque of 270 25 N m (200 18 lb.ft.).b. Tighten bolts 1 through 14 in number sequence to a torque of 470 20 N m (345 15 lb.ft.).c. Tighten bolts 1 through 14 in number sequence to a torque of 470 20 N m (345 15 lb.ft.) by hand.d. Install the rocker shaft assemblies and push rods. See Install Rocker Shaft Assemblies And Push Rods.e. Tighten bolts 15 through 26 in number sequence to a torque of 270 25 N m (200 18 lb.ft.).f. Tighten bolts 15 through 26 in number sequence to a torque of 450 20 N m (330 15 lb.ft.).g. Tighten bolts 15 through 26 in number sequence to a torque of 450 20 N m (330 15 lb.ft.) by hand.h. Tighten the bolts (5) to a torque of 45 7 N m (33 5 lb.ft.). If the studs for the exhaust manifold were removed, install new studs, and tighten them to a torque of 35 5 N m (26 3 lb.ft.).11. Make an adjustment to the valves to have a clearance of 0.38 mm (.015 in.) for intake and 0.76 mm (.030 in.) for exhaust. Tighten the locknuts for the valve adjustment screws to a torque of 28 4 N m (21 3 lb.ft.).12. Install the valve cover bases and the inner fuel lines. See Install Rocker Shaft Assemblies And Push Rods.13. Install the valve covers. See Install Valve Covers.14. Install plate (3).15. Connect water line (2) to the air compressor.16. Install bolts (1) for the alternator bracket.17. Install the intake manifold on the

Have questions with 105048-3980?





Group cross 105048-3980 ZEXEL

Isuzu 

9 430 615 376 
8944195152 
NOZZLE-HOLDER
9 430 616 171 
 
NOZZLE-HOLDER
 
 
NOZZLE-HOLDER
 
 
NOZZLE-HOLDER
 
 
NOZZLE-HOLDER
9 430 615 568 
 
NOZZLE-HOLDER

Isuzu 

9 430 615 311 
8943951971 
NOZZLE-HOLDER

Mitsubishi 

9 430 615 958 
ME731908 
NOZZLE-HOLDER
9 430 616 172 
 
NOZZLE-HOLDER ASSEMBLY
9 430 616 267 
 
NOZZLE-HOLDER ASSEMBLY

Mitsubishi 

9 430 615 959 
ME738554 
NOZZLE-HOLDER

Nissan-Diesel 

9 430 615 331 
1661099001 
NOZZLE-HOLDER
9 430 615 245 
16610Z5564 
NOZZLE-HOLDER
105048-3980  

105048-3970 
9 430 615 960 
16610Z5565 
NOZZLE-HOLDER
9 430 615 132 
 
NOZZLE-HOLDER ASSEMBLY
Back to top