105048-3970 ZEXEL 9 430 615 245 BOSCH NOZZLE-HOLDER 9430615245 1050483970 16610z5564

Information nozzle-holder

BOSCH 9 430 615 245 9430615245

ZEXEL 105048-3970 1050483970

NISSAN-DIESEL 16610Z5564 16610z5564

Price: query

Buy now
Add to cart Go to cart

Rating:

Buy NOZZLE-HOLDER 105048-3970 zexel genuine, new aftermarket engine parts with delivery

Scheme ###:

6.	[1]	150539-0600	SHIM D6.2&2.6T1.20
8.	[1]	150562-6300	COMPRESSION SPRING
10.	[1]	150560-2200	SLOTTED WASHER
11.	[1]	150624-1900	BUSHING
12.	[1]	150562-6400	COMPRESSION SPRING
15.	[1]	150560-1800	SLOTTED WASHER
22.	[1]	150655-1200	NOZZLE-RETAINING NUT
800S/1.	[1]	150538-9800	SHIM D6.2&2.6T0.40
800S/1.	[1]	150538-9900	SHIM D6.2&2.6T0.50
800S/1.	[1]	150539-0000	SHIM D6.2&2.6T0.52
800S/1.	[1]	150539-0100	SHIM D6.2&2.6T0.54
800S/1.	[1]	150539-0200	SHIM D6.2&2.6T0.56
800S/1.	[1]	150539-0300	SHIM D6.2&2.6T0.58
800S/1.	[1]	150539-0400	SHIM D6.2&2.6T0.60
800S/1.	[1]	150539-0500	SHIM D6.2&2.6T0.70
801S/1.	[1]	150591-1000	SHIM D7.2&3.6T0.10
801S/1.	[1]	150591-2000	SHIM D7.2&3.6T0.20
801S/1.	[1]	150591-3000	SHIM D7.2&3.6T0.30
801S/1.	[1]	150591-4000	SHIM D7.2&3.6T0.40
801S/1.	[1]	150591-5000	SHIM D7.2&3.6T0.50
801S/1.	[1]	150591-5100	SHIM D7.2&3.6T0.51
801S/1.	[1]	150591-5200	SHIM D7.2&3.6T0.52
801S/1.	[1]	150591-5300	SHIM D7.2&3.6T0.53
801S/1.	[1]	150591-5400	SHIM D7.2&3.6T0.54
801S/1.	[1]	150591-5500	SHIM D7.2&3.6T0.55
801S/1.	[1]	150591-5600	SHIM D7.2&3.6T0.56
801S/1.	[1]	150591-5700	SHIM D7.2&3.6T0.57
801S/1.	[1]	150591-5800	SHIM D7.2&3.6T0.58
801S/1.	[1]	150591-5900	SHIM D7.2&3.6T0.59
802S.	[0]	150572-0700	STOP PIN L28.44

Include in #1:

101606-9910 as NOZZLE-HOLDER

Cross reference number

Zexel num

Bosch num

Firm num

Name

105048-3970

9 430 615 245

16610Z5564 NISSAN-DIESEL

NOZZLE-HOLDER
* K 53LZ NH NH

Information:

Start By:a. remove valve covers 1. Use tooling (A), and disconnect fuel line (1) at each end. Remove the fuel line from the engine. 2. Use tool (B), and remove retainer (2) from the adapter.3. Remove the fuel injection nozzles with tooling (C) as follows:a. Install the 6V6983 Adapter and the 8T3199 Screw into nozzle assembly (3).b. Install the 8T3198 Tube over the 8T3199 Screw.c. Use the 1B4206 Nut on the 8T3199 Screw.d. Use the 1B4206 Nut on the 8T3199 Screw to pull the fuel injection nozzle from the adapter.4. Remove compression seal (4) and carbon dam seal (8) from fuel injection nozzle (3).5. Use tool (D), and remove adapter (6) from the cylinder head.6. Remove gasket (7) and seal (5) from adapter (6). The following steps are for installation of the fuel injection nozzles and adapters.7. Use tool (E) to clean the bore in adapter (6). Use an open end wrench or tap driver to turn tool (E).8. Inspect seal (5) for damage or wear. Replace the seal if necessary.9. Put washer (7) and seal (5) in position on adapter (6).10. Put liquid soap in the bores of the cylinder head and on seals (5) in the adapters.11. Put 5P3931 Anti-Seize Compound on the threads of adapter (6), and install the adapter in the cylinder head assembly.12. Use tool (D), and tighten the adapter to a torque of 205 14 N m (150 10 lb.ft.).
Make sure the correct compression seal washer (4) is used when the nozzle assembly is installed in the adapter. Only copper washers are to be used with this adapter.
13. Install compression seal washer (4), and use tool (F) to install carbon dam seal (8) on the fuel injection nozzle.14. Put fuel injection nozzle (3) in position in the adapter, and install retainer (2).15. Use tool (B) to tighten retainer (2) to a torque of 48 7 N m (35 5 lb.ft.).16. Install fuel line (1). Tighten the nuts on the fuel line with tooling (A) to a torque of 40 7 N m (30 5 lb.ft.).End By:a. install valve covers