105048-2130 ZEXEL 9 430 615 520 BOSCH NOZZLE-HOLDER 9430615520 1050482130 62153300080a

Information nozzle-holder

BOSCH 9 430 615 520 9430615520

ZEXEL 105048-2130 1050482130

ISEKI 62153300080A 62153300080a

Price: query

Buy now
Add to cart Go to cart

Rating:

Buy NOZZLE-HOLDER 105048-2130 zexel genuine, new aftermarket engine parts with delivery

Scheme ###:

3.	[2]	150562-5900	COMPRESSION SPRING
3.	[2]	150562-5900	COMPRESSION SPRING
4.	[1]	150560-1500	SLOTTED WASHER
5.	[1]	150524-5600	SPACER BUSHING
6.	[2]	150508-6000	BEARING PIN
7.	[1]	150655-1000	NOZZLE-RETAINING NUT
8.	[1]	150572-0620	STOP PIN
9.	[1]	150560-1900	SLOTTED WASHER
10.	[1]	150619-0700	O-RING
11.	[1]	150567-9100	CAP NUT
12.	[2]	026508-1240	GASKET D11.9&8.2T1
13.	[1]	150621-2001	UNION NUT
14.	[1]	029300-3100	GASKET
15.	[1]	150645-9520	INLET UNION
800S/1.	[1]	150591-1000	SHIM D7.2&3.6T0.10
800S/1.	[1]	150591-1000	SHIM D7.2&3.6T0.10
800S/1.	[1]	150591-1000	SHIM D7.2&3.6T0.10
800S/1.	[1]	150591-2000	SHIM D7.2&3.6T0.20
800S/1.	[1]	150591-3000	SHIM D7.2&3.6T0.30
800S/1.	[1]	150591-4000	SHIM D7.2&3.6T0.40
800S/1.	[1]	150591-5000	SHIM D7.2&3.6T0.50
800S/1.	[1]	150591-5100	SHIM D7.2&3.6T0.51
800S/1.	[1]	150591-5200	SHIM D7.2&3.6T0.52
800S/1.	[1]	150591-5300	SHIM D7.2&3.6T0.53
800S/1.	[1]	150591-5400	SHIM D7.2&3.6T0.54
800S/1.	[1]	150591-5500	SHIM D7.2&3.6T0.55
800S/1.	[1]	150591-5600	SHIM D7.2&3.6T0.56
800S/1.	[1]	150591-5700	SHIM D7.2&3.6T0.57
800S/1.	[1]	150591-5800	SHIM D7.2&3.6T0.58
800S/1.	[1]	150591-5900	SHIM D7.2&3.6T0.59

Include in #2:

104138-3001 as NOZZLE-HOLDER

104138-3002

Cross reference number

Zexel num

Bosch num

Firm num

Name

105048-2130

9 430 615 520

62153300080A ISEKI

NOZZLE-HOLDER
K 53LZ NOZZLE HOLDER NH NH

Information:

(1) Crossbar (from 8B7548 Puller).(2) Spacer plate.(3) S1589 Bolt with two 1S379 Washers.(4) 1D4595 Bolt.(5) 3H465 Plate.(6) 1P2403 Dial Indicator.(7) 1P2394 Adapter Plate.(8) 1P2402 Gauge Body.Make reference to Cylinder Liner Projection in Testing and Adjusting for the complete procedure.1. Install gasket and spacer plate (2) with bolts (3) and two 1S379 Washers. Tighten bolts (3) evenly in four steps: 1st step ... 14 N m (10 lb ft)2nd step ... 35 N m (25 lb ft)3rd step ... 70 N m (50 lb ft)4th step ... 95 N m (70 lb ft)2. Install tools as shown. Tighten bolts (4) evenly in four steps: 1st step ... 7 N m (5 lb ft)2nd step ... 20 N m (15 lb ft)3rd step ... 35 N m (25 lb ft)4th step ... 70 N m (50 lb ft)3. Measure cylinder liner projection with dial indicator (6) in 1P2402 Gauge Body (8) as shown. Measure at four places around each cylinder liner near the clamped area. Cylinder liner projection measurements for any cylinder liner must be ... 0.033 to 0.175 mm (.0013 to .0069 in)Maximum permissible difference between all four measurements ... 0.05 mm (.002 in)Maximum permissible difference between average projection of any two cylinder liners next to each other ... 0.05 mm (.002 in)Maximum permissible difference between average projection of all cylinder liners under one cylinder head ... 0.10 mm (.004 in) If liner projection is not correct, turn the liner to a new position within the bore. If projection can not be corrected this way, move the liner to a different bore. If the projection can not be corrected this way, make reference to Special Instruction, Form No. FMO55228 for complete instructions on the use of 8S3140 Counterboring Tool Arrangement. 4. Minimum permissible depth to machine counterbore to adjust cylinder liner projection ... 0.76 mm (.030 in) Maximum permissible depth to machine counterbore to adjust cylinder liner projection ... 1.14 mm (.045 in)Install a 0.76 mm (.030 in) shim plus any added shims necessary to get the correct cylinder liner projection. Be sure that the 0.76 mm (.030 in) shim is directly under the cylinder liner flange.