Information nozzle-holder
BOSCH
9 430 615 053
9430615053
ZEXEL
105048-2030
1050482030
ISUZU
8944743911
8944743911
Rating:
Scheme ###:
| 2. | [2] | 150508-5900 | BEARING PIN |
| 3. | [1] | 150524-4600 | SPACER BUSHING |
| 4. | [1] | 150655-0000 | NOZZLE-RETAINING NUT |
| 5. | [1] | 150560-1000 | SLOTTED WASHER |
| 6. | [1] | 150562-4300 | COMPRESSION SPRING |
| 8. | [1] | 150570-0700 | SPACER BUSHING |
| 9. | [1] | 150571-0300 | SET OF NUTS |
| 11. | [1] | 150572-0520 | STOP PIN |
| 12. | [1] | 150562-5700 | COMPRESSION SPRING |
| 13. | [1] | 150565-6300 | THREADED PIN |
| 15. | [1] | 150519-4800 | UNION NUT |
| 16. | [1] | 150623-5400 | GASKET |
| 17. | [1] | 150567-8800 | CAP NUT |
| 19. | [1] | 150613-1700 | EYE BOLT |
| 20. | [2] | 026508-1240 | GASKET D11.9&8.2T1 |
| 21. | [1] | 029300-3100 | GASKET |
| 22. | [1] | 150645-8920 | INLET UNION |
| 800S/1. | [1] | 150535-9400 | SHIM |
| 800S/1. | [1] | 150535-9400 | SHIM |
| 800S/1. | [1] | 150535-9500 | SHIM |
| 800S/1. | [1] | 150535-9600 | SHIM |
| 800S/1. | [1] | 150535-9700 | SHIM |
| 800S/1. | [1] | 150535-9800 | SHIM |
| 800S/1. | [1] | 150535-9900 | SHIM |
| 800S/1. | [1] | 150536-0000 | SHIM |
| 800S/1. | [1] | 150536-0100 | SHIM |
| 800S/1. | [1] | 150536-0200 | SHIM |
| 800S/1. | [1] | 150536-2300 | SHIM |
| 800S/1. | [1] | 150536-2400 | SHIM |
| 800S/1. | [1] | 150536-2500 | SHIM |
| 800S/1. | [1] | 150536-2600 | SHIM |
| 800S/1. | [1] | 150536-2700 | SHIM |
Cross reference number
Zexel num
Bosch num
Firm num
Name
Information:
Remove Fan Drive
1. Loosen two bolts (2) and two nuts (3). Remove bolt (1), and remove fan drive belts (4). 2. Remove the nuts and bolts that hold the fan drive in place. Remove fan drive (5).Install Fan Drive
1. Put fan drive (1) in position on the timing gear cover. 2. Install bolts (3) and the nuts loosely. Make a replacement of the belts as a set only.3. Install fan belts (4). Install bolt (2). Make an adjustment to the belt tension with tool (A). Measure the belt farthest away from the engine. Tighten new belts to a gauge indication of 120 5. After the engine is operated at high idle for a minimum of 30 minutes, make another adjustment to the belt tension. The correct tension for used belts is a gauge indication of 90 10.3. Tighten bolts (3) and the nuts that hold the fan drive in place.Disassemble Fan Drive
START BY:a. remove fan drive This is a typical later model fan drive. 1. Remove two bolts (2) that hold the fan adapter to the pulley.2. Remove fan adapter (1) from the pulley. 3. Remove bolts (3) and washer (4). Remove seal (5). 4. Remove pulley (8) from bracket (6).5. Remove bearing (10) and spacer (9) from the pulley. Remove spacer (7), seal (11) and bearing (12) from the pulley.Assemble Fan Drive
1. Install bearing (2) in the rear of pulley (3). 2. Install lip-type seal (1) with tooling (A). The lip of the seal must be away from the bearing. Put 5P960 Multipurpose Type Grease on the lip of the seal.3. Install spacer (5) so the end with the taper is toward the inside of pulley (3).4. Install spacer (6) and bearing (4) in the front of the pulley. 5. Put seal (7) on the front of the pulley. Install the pulley on bracket (8). 6. Install washer (10) and bolts (9) that hold the pulley in position.7. Install the fan drive adapter on the pulley.8. Fill the fan drive with 5P960 Multipurpose Type Grease.
1. Loosen two bolts (2) and two nuts (3). Remove bolt (1), and remove fan drive belts (4). 2. Remove the nuts and bolts that hold the fan drive in place. Remove fan drive (5).Install Fan Drive
1. Put fan drive (1) in position on the timing gear cover. 2. Install bolts (3) and the nuts loosely. Make a replacement of the belts as a set only.3. Install fan belts (4). Install bolt (2). Make an adjustment to the belt tension with tool (A). Measure the belt farthest away from the engine. Tighten new belts to a gauge indication of 120 5. After the engine is operated at high idle for a minimum of 30 minutes, make another adjustment to the belt tension. The correct tension for used belts is a gauge indication of 90 10.3. Tighten bolts (3) and the nuts that hold the fan drive in place.Disassemble Fan Drive
START BY:a. remove fan drive This is a typical later model fan drive. 1. Remove two bolts (2) that hold the fan adapter to the pulley.2. Remove fan adapter (1) from the pulley. 3. Remove bolts (3) and washer (4). Remove seal (5). 4. Remove pulley (8) from bracket (6).5. Remove bearing (10) and spacer (9) from the pulley. Remove spacer (7), seal (11) and bearing (12) from the pulley.Assemble Fan Drive
1. Install bearing (2) in the rear of pulley (3). 2. Install lip-type seal (1) with tooling (A). The lip of the seal must be away from the bearing. Put 5P960 Multipurpose Type Grease on the lip of the seal.3. Install spacer (5) so the end with the taper is toward the inside of pulley (3).4. Install spacer (6) and bearing (4) in the front of the pulley. 5. Put seal (7) on the front of the pulley. Install the pulley on bracket (8). 6. Install washer (10) and bolts (9) that hold the pulley in position.7. Install the fan drive adapter on the pulley.8. Fill the fan drive with 5P960 Multipurpose Type Grease.