105041-7111 ZEXEL 9 430 615 154 BOSCH NOZZLE-HOLDER 9430615154 1050417111 6162133111

Information nozzle-holder

BOSCH 9 430 615 154 9430615154

ZEXEL 105041-7111 1050417111

KOMATSU 6162133111 6162133111

Price: query

Buy now
Add to cart Go to cart

Rating:

Buy NOZZLE-HOLDER 105041-7111 zexel genuine, new aftermarket engine parts with delivery

Scheme ###:

4.	[1]	150510-0700	STOP PIN
6.	[1]	150562-4500	COMPRESSION SPRING
12/1.	[1]	150523-5000	SHIM D11.5&4.5T0.50
12/1.	[1]	150523-5100	SHIM D11.5&4.5T0.52
12/1.	[1]	150523-5200	SHIM D11.5&4.5T0.54
12/1.	[1]	150523-5300	SHIM D11.5&4.5T0.56
12/1.	[1]	150523-5400	SHIM D11.5&4.5T0.58
12/1.	[1]	150523-5500	SHIM D11.5&4.5T0.60
12/1.	[1]	150523-5600	SHIM D11.5&4.5T0.62
12/1.	[1]	150523-5700	SHIM D11.5&4.5T0.64
12/1.	[1]	150523-5800	SHIM D11.5&4.5T0.66
12/1.	[1]	150523-5900	SHIM D11.5&4.5T0.68
12/1.	[1]	150523-6000	SHIM D11.5&4.5T0.70
12/1.	[1]	150523-6100	SHIM D11.5&4.5T0.72
12/1.	[1]	150523-6200	SHIM D11.5&4.5T0.74
12/1.	[1]	150523-6300	SHIM D11.5&4.5T0.76
12/1.	[1]	150523-6400	SHIM D11.5&4.5T0.78
12/1.	[1]	150523-6500	SHIM D11.5&4.5T0.80
12/1.	[1]	150523-6600	SHIM D11.5&4.5T0.82
12/1.	[1]	150523-6700	SHIM D11.5&4.5T0.84
12/1.	[1]	150523-6800	SHIM D11.5&4.5T0.86
12/1.	[1]	150523-6900	SHIM D11.5&4.5T0.88
12/1.	[1]	150523-7000	SHIM D11.5&4.5T0.90
12/1.	[1]	150523-7100	SHIM D11.5&4.5T0.92
12/1.	[1]	150523-7200	SHIM D11.5&4.5T0.94
12/1.	[1]	150523-7300	SHIM D11.5&4.5T0.96
12/1.	[1]	150523-7400	SHIM D11.5&4.5T0.98
12/1.	[1]	150523-7500	SHIM D11.5&4.5T1.00
12/1.	[1]	150523-7600	SHIM D11.5&4.5T1.02
12/1.	[1]	150523-7700	SHIM D11.5&4.5T1.04
12/1.	[1]	150523-7800	SHIM D11.5&4.5T1.06
12/1.	[1]	150523-7900	SHIM D11.5&4.5T1.08
12/1.	[1]	150523-8000	SHIM D11.5&4.5T1.10
12/1.	[1]	150523-8100	SHIM D11.5&4.5T1.12
12/1.	[1]	150523-8200	SHIM D11.5&4.5T1.14
12/1.	[1]	150523-8300	SHIM D11.5&4.5T1.16
12/1.	[1]	150523-8400	SHIM D11.5&4.5T1.18
12/1.	[1]	150523-8500	SHIM D11.5&4.5T1.20
12/1.	[1]	150523-8600	SHIM D11.5&4.5T1.22
12/1.	[1]	150523-8700	SHIM D11.5&4.5T1.24
12/1.	[1]	150523-8800	SHIM D11.5&4.5T1.26
12/1.	[1]	150523-8900	SHIM D11.5&4.5T1.28
12/1.	[1]	150523-9000	SHIM D11.5&4.5T1.30
12/1.	[1]	150523-9100	SHIM D11.5&4.5T1.32
12/1.	[1]	150523-9200	SHIM D11.5&4.5T1.34
12/1.	[1]	150523-9300	SHIM D11.5&4.5T1.36
12/1.	[1]	150523-9400	SHIM D11.5&4.5T1.38
12/1.	[1]	150523-9500	SHIM D11.5&4.5T1.40
12/1.	[1]	150523-9600	SHIM D11.5&4.5T1.42
12/1.	[1]	150523-9700	SHIM D11.5&4.5T1.44
12/1.	[1]	150523-9800	SHIM D11.5&4.5T1.46
12/1.	[1]	150523-9900	SHIM D11.5&4.5T1.48
12/1.	[1]	150530-0000	SHIM D11.5&4.5T1.50
12/1.	[1]	150530-0100	SHIM D11.5&4.5T1.52
12/1.	[1]	150530-0200	SHIM D11.5&4.5T1.54
13.	[1]	150524-4400	SPACER BUSHING
20.	[1]	150651-5200	NOZZLE-RETAINING NUT
37.	[1]	150628-1900	FLANGE BUSHING

Cross reference number

Zexel num

Bosch num

Firm num

Name

105041-7111
105041-7112

9 430 615 154

6162133111 KOMATSU

NOZZLE-HOLDER
* K 53LZ NH NH

Information:

Connecting Rod
Use the 2H6782 Connecting Rod Boring Machine to recondition connecting rods and to check for connecting rod distortion. The 5P2009 Rework Group is available for the 2H6782 Connecting Rod Boring Machine. To install the rework group see Special Instruction GMG02394.Press a new piston pin bushing into the connecting rod. Assemble new rod bearings and the expansion sleeve. Tighten rod bolt nuts in the following step sequence.1. Put crankcase oil on bolt threads and seating faces of cap and nut.2. Tighten both nuts to 30 3 lb. ft. (40 4 N m).3. Put a mark on each nut and cap.4. Tighten each nut 60° from the mark.Clean spindle and slide the expansion sleeve and connecting rod into place. Install and tighten nut hand tight.Adjust the carrier to the distance between center of the bores, [center-to-center distance is 7.900 .001 in. (200.66 0.03 mm)]. Position the locating rods .25 in. (6.4 mm) from the connecting rod. Install front bushing in bracket and insert locating arbor through front bushing. Slide the centering sleeve over the end of the locating arbor. Slide the locating arbor through the rear bushing, centering sleeve, and into the connecting rod. Tighten knobs until locating rods lightly contact the connecting rod. Lock the locating rods and carrier.To check connecting rod distortion, slide locating arbor in and out of rear bushing. If the locating arbor does not slide freely, recheck horizontal location. If the locating arbor still binds, loosen the carrier clamp and raise or lower the carrier until the locating arbor slides freely. Read the vernier scale and note the variation from the nominal dimension. If the variation exceeds .010 in. (0.25 mm) the rod is distorted and should be replaced. Mark replacement rods for cylinder identification on bearing tab slot side of rod and cap.With the center-to-center distance set to the nominal dimension, set tool in boring bar and insert the boring bar and front bushing. Connect boring bar to the feed mechanism and engage the feed lever. Install the hand crank or an electric drill and flexible adapter and bore the bushing. Use a slow feed rate. Check the bore size. The size is 1.5010 .0003 in. (48.125 0.008 mm). A 5P2050 Connecting Rod Checking Fixture is available for checking connecting rods. For instructions for the use of the checking fixture see Special Instruction SMHS7366.Install connecting rod into piston with boss on rod on same side as crater in piston crown.
CONNECTING ROD AND PISTONWhen installing connecting rod and piston assemblies, inspect the threads of the rod bolts and nuts for damage. The contact surface of the nuts must be flat and free from damage. Damaged parts must be replaced.