105041-7000 ZEXEL 9 430 615 462 BOSCH NOZZLE-HOLDER 9430615462 1050417000 1722701213


 

Information nozzle-holder

BOSCH 9 430 615 462 9430615462
ZEXEL 105041-7000 1050417000
KUBOTA 1722701213 1722701213
105041-7000 NOZZLE-HOLDER
Rating:
31
Buy NOZZLE-HOLDER 105041-7000 zexel genuine, new aftermarket engine parts with delivery

Scheme ###:

4. [1] 150550-3400 STOP PIN
5. [1] 150515-9200 SLOTTED WASHER
6. [1] 150562-4000 COMPRESSION SPRING
8. [1] 150565-1800 THREADED PIN
10. [1] 150567-2700 CAP NUT
11. [1] 029331-2130 GASKET
13. [1] 150524-3500 SPACER BUSHING
20. [1] 150650-1300 NOZZLE-RETAINING NUT
21. [1] 029301-0090 GASKET
22. [1] 150645-0320 INLET UNION

Include in #2:

104047-3220 as NOZZLE-HOLDER

Cross reference number

Zexel num
Bosch num
Firm num
Name
105041-7000 
9 430 615 462 
1722701213  KUBOTA
NOZZLE-HOLDER
K 53LZ NOZZLE HOLDER NH NH
105041-7000 
9 430 615 462 
1722701213   
NOZZLE-HOLDER
K 53LZ NOZZLE HOLDER NH NH




Information:


WATER SLEEVE CLAMP
1. Clamp.3. Use water sleeve tool (2) to move water sleeve (3) into front cover.4. Remove the cylinder head retaining bolts (4) and (5).
MOVING WATER SLEEVE
2. 8S6692 Water Sleeve Tool. 3. Water sleeve.
CYLINDER HEAD
4. Bolts (four each head). 5. Bolts (eighteen each head).
Be sure fuel injection nozzles are removed before removing head. Nozzles extend through the head and nozzle tips can be broken off if nozzles are not removed from the head.
5. Install two 1P7407 Lifting Eye Bolts in the cylinder head. Attach a hoist and remove the cylinder head assembly, the weight is approx. 85 lbs. (39 kg).
REMOVING CYLINDER HEADInstall Cylinder Head Assemblies
1. Clean the mating surfaces of the cylinder head and cylinder block. Install new cylinder head gasket, clean and dry. Clean bores in cylinder head and inspect and lubricate O-rings for water sleeves.2. Install two 1P7407 Lifting Eye Bolts in the cylinder head. Attach a hoist and install the cylinder head assembly. Coat the cylinder head retaining bolt threads with 9M3710 Anti-Seize Compound. Install the bolts and tighten in the following Step sequence. Step A: Tighten bolts 1 through 18 in numerical order to 60 10 lb. ft. (8.3 1.4 mkg).Step B: Retighten bolts 1 through 18 in numerical order to 95 5 lb. ft. (13.1 0.7 mkg).Step C: Finally tighten bolts 1 through 18 in numerical order (hand tighten only) to 95 5 lb. ft. (13.1 0.7 mkg).Step D: Tighten bolts 19, 20, 21, and 22 in numerical order to 32 5 lb. ft. (4.4 0.7 mkg).
CYLINDER HEAD BOLT LOCATION3. Use the 8S6692 Water Sleeve Tool to slide water sleeve into cylinder head and install clamp.Disassemble Cylinder Head
1. Place head on the FT806 Cylinder Head Bench or the 8S6691 Cylinder Head Stand. Use FT967 Adapter Plates to mount head on the FT806 Cylinder Head Bench.2. Use a 5S1330 or 7F4291 Valve Spring Compressor (1) to remove the valves and valve springs.
REMOVING VALVES
1. 5S1330 Valve Spring Compressor illustrated.3. Use the 8S2263 Valve Spring Tester to check valve spring tension.4. The exhaust valve seats have replaceable inserts. To remove, use the 8S7170 Valve Seat Insert Puller Group.
REMOVING EXHAUST VALVE SEAT INSERTS The valve guides are cast in the cylinder head. If the guides show wear or bellmouthing, they can be restored to original tolerances through knurling.Assemble Cylinder Head
1. Lubricate valve stems with clean engine oil (SAE 30) before installing valves into cylinder head. Earlier engines use a valve spring retainer and washer combination instead of the one piece valve spring retainer shown.
CYLINDER HEAD

Have questions with 105041-7000?





Group cross 105041-7000 ZEXEL

Kubota 

105041-7000  
9 430 615 462 
1722701213 
NOZZLE-HOLDER
105041-7000  
9 430 615 462 
1722701213 
NOZZLE-HOLDER

Komatsu 

9 430 615 354 
6162133110 
NOZZLE-HOLDER
9 430 615 152 
6151113110 
NOZZLE-HOLDER
9 430 615 095 
6151113111 
NOZZLE-HOLDER
9 430 615 567 
6211113110 
NOZZLE-HOLDER
9 430 615 874 
6162133710 
NOZZLE-HOLDER
9 430 615 875 
6212113210 
NOZZLE-HOLDER
9 430 615 320 
6152113210 
NOZZLE-HOLDER
Back to top