105041-4371 ZEXEL 9 430 616 237 BOSCH NOZZLE-HOLDER 9430616237 1050414371 1153301300

Information nozzle-holder

BOSCH 9 430 616 237 9430616237

ZEXEL 105041-4371 1050414371

ISUZU 1153301300 1153301300

Price: query

Buy now
Add to cart Go to cart

Rating:

Buy NOZZLE-HOLDER 105041-4371 zexel genuine, new aftermarket engine parts with delivery

Scheme ###:

8.	[1]	150562-6500	COMPRESSION SPRING
10.	[1]	150560-2001	SLOTTED WASHER
11.	[1]	150624-2000	BUSHING
12.	[1]	150562-6600	COMPRESSION SPRING
15.	[1]	150560-2100	SLOTTED WASHER
16.	[2]	150525-1701	BEARING PIN
17.	[1]	150575-7720	LIFT PIECE
18.	[1]	150524-6700	SPACER BUSHING
19.	[2]	150508-3300	BEARING PIN
22.	[1]	150652-0600	NOZZLE-RETAINING NUT
23.	[1]	016550-1120	O-RING
800S/1.	[1]	150539-0700	SHIM D8.9&3.8T0.40
800S/1.	[1]	150539-0800	SHIM D8.9&3.8T0.50
800S/1.	[1]	150539-0900	SHIM D8.9&3.8T0.52
800S/1.	[1]	150539-1000	SHIM D8.9&3.8T0.54
800S/1.	[1]	150539-1100	SHIM D8.9&3.8T0.56
800S/1.	[1]	150539-1200	SHIM D8.9&3.8T0.58
800S/1.	[1]	150539-1300	SHIM D8.9&3.8T0.60
800S/1.	[1]	150539-1400	SHIM D8.9&3.8T0.70
801S/1.	[1]	150590-0600	SHIM D9.9&4.8T0.40
801S/1.	[1]	150590-0700	SHIM D9.9&4.8T0.50
801S/1.	[1]	150590-0800	SHIM D9.9&4.8T0.52
801S/1.	[1]	150590-0900	SHIM D9.9&4.8T0.54
801S/1.	[1]	150590-1000	SHIM D9.9&4.8T0.56
801S/1.	[1]	150590-1100	SHIM D9.9&4.8T0.58
801S/1.	[1]	150590-1200	SHIM D9.9&4.8T0.60
801S/1.	[1]	150590-1300	SHIM D9.9&4.8T0.70
802S.	[0]	150583-0000	STOP PIN L36.06

Include in #1:

106671-6441 as NOZZLE-HOLDER

Cross reference number

Zexel num

Bosch num

Firm num

Name

105041-4371

9 430 616 237

1153301300 ISUZU

NOZZLE-HOLDER
K 53LZ NOZZLE HOLDER NH NH

Information:

Exhaust Manifold Removal And Installation
1-Inlet air pipe. 2-Exhaust elbow. 3-Turbocharger oil drain line. 4-Turbocharger oil supply line. 5-Turbocharger. 6-Fuel injection lines (six). 7-Heat shield. 8-Exhaust manifold (three sections).Turbocharger Removal And Installation
Refer to SERVICE GUIDE for Preliminary Information.
1-Exhaust elbow. 2-Turbocharger oil supply line. 3-Bolts and nuts (two each). 4-Bolts, locks and nuts (four each). 5-Turbocharger oil drain line. 6-Inlet air pipe. Apply 9M3710 Anti-Seize Compound to threads of bolts (3 and 4) when installing turbocharger.Turbocharger Disassembly And Assembly
8S9944 Turbine Holder.1,3,5 Remove nut (1). Position the compressor end of housing (5) in an oil bath so only impeller (3) is immersed in oil. Heat impeller to 350° F. (176° C.) for not longer than ten minutes. Remove unit from oil bath and press the shaft and turbine wheel from impeller (3).1,3,5 At installation, heat impeller (3) to a maximum of 350°F. (176°C.) for not longer than ten minutes and proceed as follows: For ease of impeller installation, place the turbine wheel end of center housing (5) in an 8S9944 Turbine Holder.a. Immediately install impeller (3) on shaft, install nut (1) and tighten it to 120 lb. in. (138,4 cm.kg).b. Allow impeller to cool to less than 150°F. (65, 49°C.) and remove nut (1).c. Clean and smooth the washer face of nut (1). Lightly oil the threads of turbine shaft and nut and install the nut.d. Tighten nut (1) to 20 lb. in. (23,0 cm.kg), then tighten an additional 120°.2 Coat threads with 9M3710 Anti-Seize Compound.4,5 Install thrust plate assembly (4) so oil hole aligns with oil hole in housing (5).