Information nozzle-holder
BOSCH
9 430 615 303
9430615303
ZEXEL
105041-3131
1050413131
Rating:
Scheme ###:
| 8. | [1] | 150562-1700 | COMPRESSION SPRING |
| 10. | [1] | 150550-4700 | STOP PIN |
| 16. | [2] | 150525-1701 | BEARING PIN |
| 18. | [1] | 150524-6000 | SPACER BUSHING |
| 19. | [2] | 150508-3300 | BEARING PIN |
| 22. | [1] | 150651-8500 | NOZZLE-RETAINING NUT |
| 34. | [1] | 016550-1120 | O-RING |
| 800S/1. | [1] | 150530-4200 | SHIM D10.3&4.5T0.55 |
| 800S/1. | [1] | 150530-4400 | SHIM D10.3&4.5T0.6 |
| 800S/1. | [1] | 150530-4600 | SHIM D10.3&4.5T0.65 |
| 800S/1. | [1] | 150530-4800 | SHIM D10.3&4.5T0.7 |
| 800S/1. | [1] | 150530-5000 | SHIM D10.3&4.5T0.75 |
| 800S/1. | [1] | 150530-5000 | SHIM D10.3&4.5T0.75 |
| 800S/1. | [1] | 150530-5200 | SHIM D10.3&4.5T0.8 |
| 800S/1. | [1] | 150530-5400 | SHIM D10.3&4.5T0.85 |
| 800S/1. | [1] | 150530-5600 | SHIM D10.3&4.5T0.9 |
| 800S/1. | [1] | 150530-5800 | SHIM D10.3&4.5T0.95 |
Cross reference number
Zexel num
Bosch num
Firm num
Name
Information:
2. Remove nuts (1) from studs for main bearing caps (2).3. Remove the main bearing caps.4. Install rubber hose over each of the two studs at both ends of the block. This will protect the crankshaft during removal and installation. 5. Remove the crankshaft from the cylinder block. Weight of crankshaft is 300 lb. (136 kg).6. Remove the main bearings from cylinder block and main bearing caps.
If main bearings are not replaced, old bearings must be installed in same location from which they were removed.
Install Crankshaft
1. Put timing marks (1) on all timing gears in alignment.2. Clean surfaces for bearings in cylinder block. Install upper halves of bearings in block. Put clean oil on bearings.
If replacement of the bearings is not made, old bearings must be installed in same location from which they were removed.
3. Clean bearing caps, and install lower halves of bearings in caps. 4. Fasten a hoist to crankshaft and put it into place in the block with "V" mark on crankshaft gear in alignment with "V" mark on cluster gear. 5. Check bearing clearance with wire (A). Install bearing caps, and tighten both nuts to 75 5 lb. ft. (101.7 6.8 N m). Put a mark across the nuts and studs, and turn nuts an additional 120° from mark. Remove caps and check thickness of wire (A) to find bearing clearance. Bearing clearance must be .0035 to .0066 in. (0.089 to 0.168 mm) for new parts. Maximum permissible clearance for used parts is .010 in. (0.25 mm).6. Put clean oil on threads of studs, face of nuts, and lower halves of bearings. Put bearing caps in their respective positions with number on cap same as number on block, and groove in bearing cap on same side as groove in cylinder block. Install nuts and tighten to 75 5 lb.ft. (101.7 6.8 N m). Put a mark across the nuts and studs, and turn nuts an additional 120° from mark. 7. Use indicator group (B) to check the crankshaft end plate as controlled by lower bearing of No. 7 bearing cap. End play with new parts should be .006 to .018 in. (0.15 to 0.46 mm). Maximum permissible end play with used parts is .035 in. (0.89 mm).end by: a) install flywheel housingb) install front coverc) install pistonsd) install engine and torque divider
If main bearings are not replaced, old bearings must be installed in same location from which they were removed.
Install Crankshaft
1. Put timing marks (1) on all timing gears in alignment.2. Clean surfaces for bearings in cylinder block. Install upper halves of bearings in block. Put clean oil on bearings.
If replacement of the bearings is not made, old bearings must be installed in same location from which they were removed.
3. Clean bearing caps, and install lower halves of bearings in caps. 4. Fasten a hoist to crankshaft and put it into place in the block with "V" mark on crankshaft gear in alignment with "V" mark on cluster gear. 5. Check bearing clearance with wire (A). Install bearing caps, and tighten both nuts to 75 5 lb. ft. (101.7 6.8 N m). Put a mark across the nuts and studs, and turn nuts an additional 120° from mark. Remove caps and check thickness of wire (A) to find bearing clearance. Bearing clearance must be .0035 to .0066 in. (0.089 to 0.168 mm) for new parts. Maximum permissible clearance for used parts is .010 in. (0.25 mm).6. Put clean oil on threads of studs, face of nuts, and lower halves of bearings. Put bearing caps in their respective positions with number on cap same as number on block, and groove in bearing cap on same side as groove in cylinder block. Install nuts and tighten to 75 5 lb.ft. (101.7 6.8 N m). Put a mark across the nuts and studs, and turn nuts an additional 120° from mark. 7. Use indicator group (B) to check the crankshaft end plate as controlled by lower bearing of No. 7 bearing cap. End play with new parts should be .006 to .018 in. (0.15 to 0.46 mm). Maximum permissible end play with used parts is .035 in. (0.89 mm).end by: a) install flywheel housingb) install front coverc) install pistonsd) install engine and torque divider