105041-3110 ZEXEL 9 430 615 268 BOSCH NOZZLE-HOLDER 9430615268 1050413110 me738568

Information nozzle-holder

BOSCH 9 430 615 268 9430615268

ZEXEL 105041-3110 1050413110

MITSUBISHI ME738568 me738568

Price: query

Buy now
Add to cart Go to cart

Rating:

Buy NOZZLE-HOLDER 105041-3110 zexel genuine, new aftermarket engine parts with delivery

Scheme ###:

8.	[1]	150562-6500	COMPRESSION SPRING
10.	[1]	150560-2001	SLOTTED WASHER
11.	[1]	150624-1800	BUSHING
12.	[1]	150562-6600	COMPRESSION SPRING
15.	[1]	150560-2100	SLOTTED WASHER
22.	[1]	150651-6000	NOZZLE-RETAINING NUT
40.	[2]	026508-1240	GASKET D11.9&8.2T1
42.	[1]	150613-1801	EYE BOLT
800S/1.	[1]	150539-0700	SHIM D8.9&3.8T0.40
800S/1.	[1]	150539-0800	SHIM D8.9&3.8T0.50
800S/1.	[1]	150539-0900	SHIM D8.9&3.8T0.52
800S/1.	[1]	150539-1000	SHIM D8.9&3.8T0.54
800S/1.	[1]	150539-1100	SHIM D8.9&3.8T0.56
800S/1.	[1]	150539-1200	SHIM D8.9&3.8T0.58
800S/1.	[1]	150539-1300	SHIM D8.9&3.8T0.60
800S/1.	[1]	150539-1400	SHIM D8.9&3.8T0.70
801S/1.	[1]	150590-0600	SHIM D9.9&4.8T0.40
801S/1.	[1]	150590-0700	SHIM D9.9&4.8T0.50
801S/1.	[1]	150590-0800	SHIM D9.9&4.8T0.52
801S/1.	[1]	150590-0900	SHIM D9.9&4.8T0.54
801S/1.	[1]	150590-1000	SHIM D9.9&4.8T0.56
801S/1.	[1]	150590-1100	SHIM D9.9&4.8T0.58
801S/1.	[1]	150590-1200	SHIM D9.9&4.8T0.60
801S/1.	[1]	150590-1300	SHIM D9.9&4.8T0.70
802S.	[0]	150583-0000	STOP PIN L36.06

Include in #1:

107691-2091 as NOZZLE-HOLDER

Cross reference number

Zexel num

Bosch num

Firm num

Name

105041-3110

9 430 615 268

ME738568 MITSUBISHI

NOZZLE-HOLDER
K 53LZ NOZZLE HOLDER NH NH

Information:

1. Bend the tabs of the locks from bolts (2) and remove bolts (2) and sleeve (1).2. Remove five bolts (3) from the flywheel housing. 3. Remove the two bolts and remove tachometer drive (8) from flywheel housing (7).4. Remove the five bolts that hold the flywheel housing to the timing gear plate on the left side of the engine.5. Remove two bolts (5), the three bolts (6) and bolt (9).6. Remove the two bolts that hold the flywheel housing to the timing gear plate at the accessory drive on the right side of the engine.7. Remove nuts (4), and use two persons to remove flywheel housing (7). The weight of the flywheel housing is 90 lb. (41 kg).Install Flywheel Housing
1. Clean the surface of the timing gear plate and put the flywheel housing gasket in position. 2. Put flywheel housing (1) in position and install the nuts and bolts to hold it. 3. Tighten two bolts (3) to a torque of 40 5 lb. ft. (55 7 N m). Tighten three bolts (2) to a torque of 95 10 lb. ft. (130 14 N m). 4. Put the O-ring seal (4) on tachometer drive and install the tachometer drive. Make sure tachometer drive is correctly engaged with the drive shaft before the bolts that hold it are tightened. 5. Install sleeve (5) evenly on the crankshaft rear seal and install the bolts and locks to hold it.end by: a) install BrakeSaverb) install BrakeSaver control valvec) install electric starting motord) install air compressore) install oil pan