105030-4850 ZEXEL 9 430 615 406 BOSCH NOZZLE-HOLDER 9430615406 1050304850 236202670a

Information nozzle-holder

BOSCH 9 430 615 406 9430615406

ZEXEL 105030-4850 1050304850

HINO 236202670A 236202670a

Price: query

Buy now
Add to cart Go to cart

Rating:

Buy NOZZLE-HOLDER 105030-4850 zexel genuine, new aftermarket engine parts with delivery

Scheme ###:

8.	[1]	150562-4400	COMPRESSION SPRING
10.	[1]	150560-1601	SLOTTED WASHER
16.	[2]	150525-1701	BEARING PIN
18.	[1]	150524-5700	SPACER BUSHING
19.	[2]	150508-3300	BEARING PIN
22.	[1]	150651-9400	NOZZLE-RETAINING NUT
24.	[1]	150550-5700	STOP PIN
26.	[1]	150562-4400	COMPRESSION SPRING
28.	[1]	150565-7100	THREADED PIN
30.	[1]	029331-4130	GASKET
31.	[1]	150567-3000	CAP NUT
40.	[1]	150623-6200	GASKET
42.	[1]	150613-1801	EYE BOLT
800S/1.	[1]	150538-4900	SHIM D9.5&4.5T0.40
800S/1.	[1]	150538-5000	SHIM D9.5&4.5T0.50
800S/1.	[1]	150538-5100	SHIM D9.5&4.5T0.52
800S/1.	[1]	150538-5200	SHIM D9.5&4.5T0.54
800S/1.	[1]	150538-5300	SHIM D9.5&4.5T0.56
800S/1.	[1]	150538-5400	SHIM D9.5&4.5T0.58
800S/1.	[1]	150538-5500	SHIM D9.5&4.5T0.60
800S/1.	[1]	150538-5600	SHIM D9.5&4.5T0.70
801S/1.	[1]	150575-0000	LIFT PIECE T2.860
801S/1.	[1]	150575-0200	LIFT PIECE T2.870
801S/1.	[1]	150575-0400	LIFT PIECE T2.880
801S/1.	[1]	150575-0600	LIFT PIECE T2.890
801S/1.	[1]	150575-0800	LIFT PIECE T2.900
801S/1.	[1]	150575-1000	LIFT PIECE T2.910
801S/1.	[1]	150575-1200	LIFT PIECE T2.920
801S/1.	[1]	150575-1400	LIFT PIECE T2.930
801S/1.	[1]	150575-1600	LIFT PIECE T2.940
801S/1.	[1]	150575-1800	LIFT PIECE T2.950
801S/1.	[1]	150575-2000	LIFT PIECE T2.960
801S/1.	[1]	150575-2200	LIFT PIECE T2.970
801S/1.	[1]	150575-2400	LIFT PIECE T2.980
801S/1.	[1]	150575-2600	LIFT PIECE T2.990
801S/1.	[1]	150575-2800	LIFT PIECE T3.000
801S/1.	[1]	150575-3000	LIFT PIECE T3.010
801S/1.	[1]	150575-3200	LIFT PIECE T3.020
801S/1.	[1]	150575-3400	LIFT PIECE T3.030
801S/1.	[1]	150575-3600	LIFT PIECE T3.040
801S/1.	[1]	150575-3800	LIFT PIECE T3.050
801S/1.	[1]	150575-4000	LIFT PIECE T3.060
801S/1.	[1]	150576-3000	LIFT PIECE
801S/1.	[1]	150576-3200	LIFT PIECE
801S/1.	[1]	150576-3400	LIFT PIECE
801S/1.	[1]	150576-3600	LIFT PIECE
801S/1.	[1]	150576-3800	LIFT PIECE
801S/1.	[1]	150576-4000	LIFT PIECE

Include in #1:

101603-2490 as NOZZLE-HOLDER

Cross reference number

Zexel num

Bosch num

Firm num

Name

105030-4850

9 430 615 406

236202670A HINO

NOZZLE-HOLDER
K 53LZ NOZZLE HOLDER NH NH

Information:

Install the pump cover onto the pump housing. Tighten the four middle bolts. Then, tighten the end bolts in a crisscross pattern. Tighten the bolts to a torque of 10.2 N m (90 lb in).Note: Make sure that the gasket is in place between the housing and the cover.
Repeat Step 1 and Step 2 in order to confirm the electrical connection for the pump coil was not damaged during the removal of the pump cover.
Install the oil inlet line adapter, inlet line, and harness connector to the pump.Note: After the HEUI pump is replaced or reassembled, the engine must be cranked for an extended length of time to fill the pump with oil.Note: Clear any diagnostic or event codes that activated during the initial start-up.
If the engine would not start before inspecting for debris and no debris was found in the HEUI pump, return to Step D in the diagnostic flow chart.If the engine would start before inspecting for debris and no debris was found in the HEUI pump, return to Step L in the diagnostic flow chart.If the pump is to be replaced, complete the checklist form in Special Instruction, REHS5031 that is provided with the service replacement part and insert the completed form back into the box containing the part that is being returned. Proceed to the section of this instruction titled "Oil Rail Cleaning Procedure" for the correct engine size that is being serviced.Oil Rail Cleaning Procedure For the C7 Engine
Illustration 12 g02702636
C7 Cylinder Head
Illustration 13 g02708256
The oil and fuel passages are the same for both the C7 and C9.
(6) Oil Rail for a HEUI fuel system
(7) Oil passage to injector bore
(8) Fuel passage
(9) Injector bore Note: Contain any oil and cleaner that will flow from the cylinder and the lines during the following process. Properly dispose of the oil and contaminated cleaner when work is complete.
Remove fuel injectors. Refer to Disassembly and Assembly for specific machine.
Install six plugs 9U-7080 Tapered Cap/Plug into the lower injector bores. The plugs will prevent oil, cleaners, and debris from entering the cylinders.
Remove the plugs from the front and rear of the cylinder head main oil gallery
Remove the pressure sensor from the cylinder head. Protect the sensor.
Clean out the two rail drain holes by removing their plugs and using the brake cleaner and long squirting straw to flush these passages to the oil rail.
Using the solvent gun with and without the