105025-2340 ZEXEL 9 432 610 676 BOSCH NOZZLE 9432610676 1050252340 16620z5663


 

Information nozzle

BOSCH 9 432 610 676 9432610676
ZEXEL 105025-2340 1050252340
NISSAN-DIESEL 16620Z5663 16620z5663
105025-2340 NOZZLE
Rating:
16
Buy NOZZLE 105025-2340 zexel genuine, new aftermarket engine parts with delivery

Cross reference number

Zexel num
Bosch num
Firm num
Name
105025-2340 
9 432 610 676 
NP-DLLA150SM234 
16620Z5663  NISSAN-DIESEL
NOZZLE
C 50LC NOZZLE N (DLL-S) N




Information:

Fuel Recommendations
Fill the fuel tank at the end of each day of operation to drive out moist air and prevent condensation. Maintain a fairly consistent level in the day tank (near the top) to avoid drawing moisture into the tank as the level decreases.Do not fill the tank to the top. Fuel expands as it warms, and may overflow.Do not fill fuel filters with fuel before installing them. Contaminated fuel causes accelerated wear to fuel system parts.
Use fuel only as recommended in this section. Fuel grades recommended for use in Caterpillar diesel engines are: No.2-D diesel fuel with low sulfur (0.05 percent maximum), or regular sulfur (0.5 percent maximum). No. 1 grades are acceptable.The following chart lists worldwide fuel standards which meet Caterpillar requirements. Aviation kerosene-type fuels meeting acceptable limits may also be used as an engine fuel. The following chart lists some of the acceptable kerosene-type fuels. Fuel viscosity is a major concern with aviation fuels. A minimum viscosity of 1.4 cSt at 38°C (100°F) is required to properly lubricate Caterpillar fuel system components. These kerosene-type fuels have a lower viscosity for low temperature operation.The kerosene-type fuels have less energy per unit volume than diesel fuels, producing less peak power. More kerosene-type fuel is needed than diesel fuel to do the same amount of work.Caterpillar Diesel Engines are capable of burning a wide range of distillate fuels. Burning clean, stable blends of distillate fuel meeting the following requirements will provide quality engine service life. When economics or fuel availability dictate, other fuel types may be burned in the engine. Consult your Caterpillar dealer for more information and advice on any specific fuel.Cetane Number
Under average starting conditions, direct injection engines require a minimum cetane number of 40. A higher cetane value may be required for high altitude or cold weather operation.Filterability
Clean fuels should have no more than 0.1 percent of sediment and water. Fuel stored for extended periods of time may oxidize and form solids, causing filtering problems.Pour Point
Fuel pour point should be at least 6°C (10°F) below the lowest ambient temperature at which the engines must start and operate. Lower pour points of No.1 or No.1-D fuel may be necessary in extremely cold weather.Cloud Point
The cloud point should be below the lowest ambient temperature at which the engines must start and operate, to prevent the fuel filter elements from plugging with wax crystals. Refer to Fuel Problems in Cold Weather Operation for additional information.Viscosity
Fluid viscosity is a measure of resistance to flow. Fuel viscosity is important because it effects lubrication of fuel system components, and fuel atomization. The provided viscosity limits address both of those effects.Additives
Fuel additives are generally not recommended or needed for the specified fuels listed. Acetone improvers can be used as necessary for direct injection engine requirements. Biocides may be needed to eliminate microorganism growth in storage tanks. In cold conditions, treatment for entrained water may also be necessary.Consult your fuel supplier about the use of additives to prevent incompatibility among additives already in

Have questions with 105025-2340?





Group cross 105025-2340 ZEXEL

Hino 

9 432 610 700 
NP-DLLA155SM230 
236402700A 
NOZZLE

Komatsu 

9 432 611 579 
NP-DLL155SM231 
6212117120 
NOZZLE
9 432 612 643 
NP-DLLA155SM232 
 
NOZZLE

Hino 

9 432 611 580 
NP-DLLA150SM233 
236401880A 
NOZZLE

Nissan-Diesel 

105025-2340  
9 432 610 676 
NP-DLLA150SM234 
16620Z5663 
NOZZLE

Mitsubishi 

9 432 611 581 
NP-DLLA148SM235 
ME748134 
NOZZLE
9 432 611 582 
NP-DLLA148SM236 
ME748295 
NOZZLE

Isuzu 

9 432 611 583 
NP-DLLA165SM237 
1153112940 
NOZZLE

Hino 

9 432 611 584 
NP-DLLA150SM238 
236402710A 
NOZZLE
9 432 612 644 
NP-DLLA155SM239 
 
NOZZLE
Back to top