105015-8100 ZEXEL 9 432 611 281 BOSCH NOZZLE 9432611281 1050158100 1153112050


 

Information nozzle

BOSCH 9 432 611 281 9432611281
ZEXEL 105015-8100 1050158100
ISUZU 1153112050 1153112050
105015-8100 NOZZLE
Rating:
26
Buy NOZZLE 105015-8100 zexel genuine, new aftermarket engine parts with delivery

Cross reference number

Zexel num
Bosch num
Firm num
Name
105015-8100 
9 432 611 281 
NP-DLLA149SN810 
1153112050  ISUZU
NOZZLE
C 50LC NOZZLE N (DLL-S) N




Information:

Start By:a. remove cylinder headb. remove oil panc. remove underframe 1. Remove bolt and remove cooling jet (1).2. Check the connecting rods and caps for their identification and location. The connecting rod and the rod cap should have the cylinder number etched on the right side indicated by the arrow. If not marked, etch each unmarked connecting rod/or cap during removal.3. Remove rod cap bolts (2) and the cap from the connecting rod. Remove the lower half of the bearing from the cap. 4. Push piston and connecting rod (4) away from the crankshaft, then remove upper half of the rod bearing (5).5. Remove the piston and connecting rod. The following steps are for the installation of the pistons and connecting rod assemblies.6. Put clean oil on piston rings, piston and cylinder bore. 7. Position the piston ring end gaps 120° apart and install tooling (A).8. With number one crankshaft throw at bottom center, install piston and connecting rod. Some engines use pistons which have the word "FRONT" stamped on the crown of the piston. Make sure the word "FRONT" is toward the front of the engine when the piston is installed. The etched number on the connecting rod must be on the right side and must be installed in the corresponding cylinder.9. Taking care to line up connecting rod and crankshaft, carefully tap piston into cylinder bore until tooling (A) comes off the piston.10. Before connecting rod comes in contact with crankshaft, install upper half of rod bearing. Be sure the bearing tab properly engages the slot in the connecting rod.11. Put engine oil on upper rod bearing surface, then tap piston down, guiding connecting rod onto crankshaft.12. Position lower half of rod bearing in corresponding numbered rod cap. Be sure the bearing tab engages the grove in the rod caps.13. Put engine on the lower rod bearing surface, then install the rod cap. Install the bearing cap on the connecting rod with the number on the bearing (rod) cap on the same side and same number as on the connecting rod.14. Put 2P2506 Thread Lubricant on the threads of the bolts. Install rod cap bolts (1) and tighten them to a torque of 130 7 N m (95 5 lb ft). Mark each bolt head and then tighten each bolt an additional 1/6 60 5° ( turn).15. Repeat the steps for the remainder of the pistons and connecting rods.End By:a. install underframeb. install oil panc. install cylinder headDisassemble & Assemble Pistons And Connecting Rods
Start By:a. remove pistons and connecting rods 1. Use tooling (A) and remove piston rings (1) from piston crown (2). 2. Remove snap ring and remove piston pin (3). Separate piston crown (2), piston skirt (4) and connecting rod (5). The connecting rod must be heated for the installation of the piston pin bearing. Do not use a torch.3. Heat connecting rod (5) in the area indicated by the illustration to a temperature of 175 to 260° C (347 to

Have questions with 105015-8100?





Group cross 105015-8100 ZEXEL

Isuzu 

105015-8100  
9 432 611 281 
NP-DLLA149SN810 
1153112050 
NOZZLE
9 432 611 282 
NP-DLLA150SN811 
1153112070 
NOZZLE

Hino 

9 432 611 283 
NP-DLLA150SN812 
236401830A 
NOZZLE
9 432 611 284 
NP-DLLA160SN813 
236401790A 
NOZZLE
9 432 611 285 
NP-DLLA150SN814 
236401800A 
NOZZLE

Nissan-Diesel 

9 432 610 888 
NP-DLLA155SN815 
16620Z5564 
NOZZLE
9 432 611 286 
NP-DLLA157SN816 
1662095500 
NOZZLE
9 432 611 224 
NP-DLLA151SN817 
1662096565 
NOZZLE

Hino 

9 432 610 742 
NP-DLLA150SN818 
236401840A 
NOZZLE
9 432 612 356 
NP-DLLA149SN819 
 
NOZZLE

Isuzu 

9 432 611 183 
NP-DLLA149SN819 
1153111890 
NOZZLE
9 432 611 249 
NP-DLLA149SN819 
1153111891 
NOZZLE
Back to top