105015-4290 ZEXEL 9 432 611 767 BOSCH NOZZLE 9432611767 1050154290 1662097010


 

Information nozzle

BOSCH 9 432 611 767 9432611767
ZEXEL 105015-4290 1050154290
NISSAN-DIESEL 1662097010 1662097010
105015-4290 NOZZLE
Rating:
11
Buy NOZZLE 105015-4290 zexel genuine, new aftermarket engine parts with delivery

Cross reference number

Zexel num
Bosch num
Firm num
Name
105015-4290 
9 432 611 767 
NP-DLLA148S354N429 
1662097010  NISSAN-DIESEL
NOZZLE
* C




Information:

Crankcase Breather
Clean
1. Loosen breather retaining clamp (1) on breather.2. Loosen hose clamp (2) and remove breather assembly.3. Wash breather in clean, nonflammable solvent and allow to dry.4. Install new seal.5. Assemble breather and install in reverse order of removal.6. Tighten all hose clamps (2) to 27 4.5 lb in (3.0 0.5 N m) If the crankcase breather is not maintained on a regular basis, it will become plugged. A plugged crankcase breather would result in excessive crankcase pressure that may cause crankshaft seal leakage.Refer to the Torque Specifications section of this manual for Torque for Standard Hose Clamps-Worm Drive Band Type hose clamps if your engine is equipped.Alternator, Fan and Accessory Drive Belts
Inspect
Inspect the drive belts for wear and replace if they show any signs of wear.If one belt in a set requires replacement, always install a new matched set of belts. Never replace just the worn belt. If only the worn belt is replaced, the new belt will carry all the load, as it will not be stretched as much as the older belts. All the belts will fail in rapid succession.If belts are too loose, they vibrate enough to cause unnecessary wear on the belts and pulleys.If belts are too tight, unnecessary stresses are placed upon the pulley bearings and belts which might shorten the life of both. 1. Inspect the condition and adjustment of alternator belts and fan drive belts.2. To check the belt tension, apply 25 lbs (110 N) of force midway between the pulleys. Correctly adjusted belts will deflect 1/2 to 3/4 inch (13 to 19 mm).Adjust Alternator Belts
1. To adjust the alternator drive belts, loosen mounting bolt(s) (1) and adjusting bracket nut(s) (2).2. Adjust the alternator in or out by either tightening or loosening adjusting nut(s) (2), as required, to obtain the correct adjustment.3. Tighten bolts (1) and nuts (2).4. If new belts are installed, check belt adjustment again after 30 minutes of engine operation. Replace belts in matched sets only. If only one belt of a matched set is replaced, it will carry more of a load than the belts not replaced since the older belts are stretched. The additional load on the new belt could cause it to break.Adjust Fan Drive Belts
5. To adjust the fan drive belts, loosen mounting bolts and adjust with adjusting bolt.6. Move the fan drive up or down as required to obtain the correct adjustment. Tighten mounting bolts.7. If new belts are installed, check belt adjustment again after 30 minutes of engine operation.Refer to the Service Manual for 3406B PEEC Truck Engines for more information or see your Caterpillar dealer.Hoses and Clamps
Inspect/Replace
Hose replacement prior to failure is a cost effective preventive maintenance practice. Replacing a hose before it fails saves money and reduces the chances for unscheduled downtime. By replacing a hose that is cracked, soft or leaking, you will avoid major repairs that could result in a severe engine overheating problem.Inspect all hoses for leaks due to cracking, softness and loose clamps.

Have questions with 105015-4290?





Group cross 105015-4290 ZEXEL

9 432 612 314 
NP-DLLA160S354N420 
 
NOZZLE

Mitsubishi 

9 432 610 046 
NP-DLLA160S295N422 
ME036781 
NOZZLE
 
3626101600 

Isuzu 

9 432 611 754 
NP-DLLA154S344N424 
1153110780 
NOZZLE

Nissan-Diesel 

9 432 610 759 
NP-DLLA151S354N425 
1662097008 
NOZZLE

Isuzu 

9 432 610 215 
NP-DLLA160S385N426 
1153111100 
NOZZLE
9 432 610 410 
NP-DLLA160S424N427 
1153111110 
NOZZLE
9 432 611 760 
NP-DLLA154S344N428 
1153111030 
NOZZLE

Nissan-Diesel 

105015-4290  
9 432 611 767 
NP-DLLA148S354N429 
1662097010 
NOZZLE
Back to top