Information nozzle
BOSCH
9 432 610 065
9432610065
ZEXEL
105015-4060
1050154060
KOMATSU
6136113120
6136113120
Rating:
Compare Prices: .
As an associate, we earn commssions on qualifying purchases through the links below
4PCS 105015-4060 6136-12-3120 DLLA152S354N406 Injector Nozzle Compatible With Komatsu S6D105 6D105 A412 Excavator
GBQZKPVXN Fast response and stable power. || Stable performance and few failures. || Optimize combustion and reduce emissions. || Efficient and energy-saving, reducing fuel consumption. || The installation process is simple and convenient
GBQZKPVXN Fast response and stable power. || Stable performance and few failures. || Optimize combustion and reduce emissions. || Efficient and energy-saving, reducing fuel consumption. || The installation process is simple and convenient
4PCS 105015-4060 6136-12-3120 DLLA152S354N406 Injector Nozzle Compatible With Komatsu S6D105 6D105 A412 Excavator
BDCZKAIEG The fuel nozzle sprays fuel into the engine cylinder in the form of atomization through electromagnetic control or mechanical control. || 2. Good atomization can make fuel and air mix more fully and improve the combustion quality. || 3. It determines the injection speed and range of fuel and has an important influence on the combustion process. || 4. Accurately control the fuel flow according to the working condition and load of the engine. || 5. Optimizing fuel injection can reduce harmful gas emission and meet environmental protection standards.
BDCZKAIEG The fuel nozzle sprays fuel into the engine cylinder in the form of atomization through electromagnetic control or mechanical control. || 2. Good atomization can make fuel and air mix more fully and improve the combustion quality. || 3. It determines the injection speed and range of fuel and has an important influence on the combustion process. || 4. Accurately control the fuel flow according to the working condition and load of the engine. || 5. Optimizing fuel injection can reduce harmful gas emission and meet environmental protection standards.
$240.25
05 Sep 2023
0.0022[0.00] Pounds
CN: 98765678910
4PCS 105015-4060 6136-12-3120 DLLA152S354N406 Injector Nozzle Compatible With Komatsu S6D105 6D105 A412 Excavator
KOZON *Increase your throttle response and save gasoline. || *Simple installation, no complicated procedures and convenient use. || *Precision manufacturing ensures stable performance and long service life. || *Reduce overall fuel consumption, promote better engine operation, fully burn fuel and increase power. || 4PCS 105015-4060 6136-12-3120 DLLA152S354N406 Injector Nozzle Compatible With Komatsu S6D105 6D105 A412 Excavator
KOZON *Increase your throttle response and save gasoline. || *Simple installation, no complicated procedures and convenient use. || *Precision manufacturing ensures stable performance and long service life. || *Reduce overall fuel consumption, promote better engine operation, fully burn fuel and increase power. || 4PCS 105015-4060 6136-12-3120 DLLA152S354N406 Injector Nozzle Compatible With Komatsu S6D105 6D105 A412 Excavator
Cross reference number
Zexel num
Bosch num
Firm num
Name
Information:
Startability will be improved at temperatures below +32°F (0°C) by the use of a starting aid and/or use of a cylinder block coolant heater or other means to heat the crankcase oil.Start the engine using the following procedure:1. Place the transmission in NEUTRAL and disengage the flywheel clutch (if equipped) to remove the transmission drag and prevent movement of the truck. Depressing the clutch in cold weather can mean the difference between starting and not starting. Depressing the clutch in warm weather produces faster starts and reduces battery drain.2. Turn the ignition switch to the ON position and push the crank button or turn the ignition switch to the START position. Crank the engine. (At temperatures below +32°F (0°C), it may be necessary to spray starting fluid into the air cleaner inlet.) DO NOT PUSH DOWN OR HOLD THE THROTTLE DOWN while cranking the engine. The PEEC system will automatically provide the correct amount of fuel to start the engine. The PEEC equipped engine may need to crank slightly longer than a mechanically governed engine, because some oil pressure is required for the electronic actuator to move the rack. The "CHECK ENGINE" light should be ON while the engine is cranking, but should go OFF after engine oil pressure is achieved.If the engine fails to start in 30 seconds, release the starter switch and wait two minutes to allow the starter motor to cool before using it again.
When using starting fluid, follow the manufacturer's instructions carefully, use it sparingly and spray it only while cranking the engine. Also, do not store starting fluid containers in the cab. Failure to do so, could result in an explosion and/or fire and possible personal injury.
Excessive ether can cause piston and ring damage. Use ether for cold starting purposes only.
3. As soon as the engine starts, allow the engine to idle for two or three minutes, or until the water temperature gauge indicator has begun to rise.4. Do not apply load to the engine or increase engine speed until the oil pressure gauge indicates normal. Oil pressure should rise within 15 seconds after the engine starts.5. Operate the engine at low load until all systems reach operating temperature. Check all gauges during the warm-up period.Starting With Jumper Cables
Batteries give off flammable fumes that can explode. Improper jumper cable connections can cause an explosion resulting in personal injury.Prevent sparks near the batteries. Sparks could cause vapors to explode. Do not allow jumper cable ends to contact each other or the engine.Do not smoke when observing the battery electrolyte levels.Always wear protective glasses when working with batteries.Electrolyte is an acid and can cause personal injury if it contacts skin or eyes.
Engines installed without engine-to-frame ground straps can be damaged by electrical discharge.To prevent electrical discharge damage, check to make sure the engine's electrical system has an engine-to-frame ground strap. For engines which have the alternator connected to an engine component, the ground strap must connect that component to the frame.Some engines have starter-to-frame
When using starting fluid, follow the manufacturer's instructions carefully, use it sparingly and spray it only while cranking the engine. Also, do not store starting fluid containers in the cab. Failure to do so, could result in an explosion and/or fire and possible personal injury.
Excessive ether can cause piston and ring damage. Use ether for cold starting purposes only.
3. As soon as the engine starts, allow the engine to idle for two or three minutes, or until the water temperature gauge indicator has begun to rise.4. Do not apply load to the engine or increase engine speed until the oil pressure gauge indicates normal. Oil pressure should rise within 15 seconds after the engine starts.5. Operate the engine at low load until all systems reach operating temperature. Check all gauges during the warm-up period.Starting With Jumper Cables
Batteries give off flammable fumes that can explode. Improper jumper cable connections can cause an explosion resulting in personal injury.Prevent sparks near the batteries. Sparks could cause vapors to explode. Do not allow jumper cable ends to contact each other or the engine.Do not smoke when observing the battery electrolyte levels.Always wear protective glasses when working with batteries.Electrolyte is an acid and can cause personal injury if it contacts skin or eyes.
Engines installed without engine-to-frame ground straps can be damaged by electrical discharge.To prevent electrical discharge damage, check to make sure the engine's electrical system has an engine-to-frame ground strap. For engines which have the alternator connected to an engine component, the ground strap must connect that component to the frame.Some engines have starter-to-frame