105012-0931 ZEXEL 9 432 612 228 BOSCH NOZZLE 9432612228 1050120931


 

Information nozzle

BOSCH 9 432 612 228 9432612228
ZEXEL 105012-0931 1050120931
105012-0931 NOZZLE
Rating:
26
Buy NOZZLE 105012-0931 zexel genuine, new aftermarket engine parts with delivery

Cross reference number

Zexel num
Bosch num
Firm num
Name
105012-0931 
9 432 612 228 
NP-DL145UE509N3 
   
NOZZLE
C 31EA NOZZLE N(DL-TA) N




Information:


Cylinder Head Bolt Tightening SequenceRemove Cylinder Head Assembly
START BY:a. remove rocker shaft assemblies and push rodsb. remove water temperature regulatorc. remove aftercooler housingd. remove fuel injection linese. remove exhaust manifold 1. Remove bolts (1) from the alternator bracket.2. Remove the bolts that hold plate (3), and remove the plate.3. Disconnect water line (2) from the air compressor. Turn the water line tee toward the lifting bracket in order to provide clearance to remove the head bolt. 4. Remove bolts (4) and (5) that hold the cylinder head assembly to the cylinder block.5. Fasten a hoist, and remove the cylinder head assembly. The weight is approximately 135 kg (300 lb.).
Do not put the cylinder head assembly down on a flat surface. This can cause damage to the fuel injection valves.
6. Remove the gasket and seals from the spacer plate.Install Cylinder Head Assembly
Be sure a new gasket has been installed between the spacer plate and the cylinder block. See Remove And Install Spacer Plate. 1. Thoroughly clean the spacer plate and the bottom surface of the cylinder head assembly. Install a new head gasket, new seals (1) and two O-ring seals (2). 2. Fasten a hoist, and put cylinder head assembly (3) in position on the cylinder block.3. Put 5P3931 Anti-Seize Compound on the threads of the cylinder head bolts. Install the cylinder head bolts and washers. Tighten the bolts in sequence shown in illustration A87019X1 on page 6-119.a. Tighten bolts 1 through 20 in number sequence to a torque of 270 25 N m (200 18 lb.ft.).b. Tighten bolts 1 through 20 in number sequence to a torque of 450 20 N m (330 15 lb.ft.).c. Tighten bolts 1 through 20 in number sequence to a torque of 450 20 N m (330 15 lb.ft.) by hand.d. Install the rocker shaft assemblies and push rods. See Install Rocker Shaft Assemblies And Push Rods.e. Tighten bolts 21 through 26 in number sequence to a torque of 270 25 N m (200 18 lb.ft.).f. Tighten bolts 21 through 26 in number sequence to a torque of 450 20 N m (330 15 lb.ft.).g. Tighten bolts 21 through 26 in number sequence to a torque of 450 20 N m (330 15 lb.ft.) by hand.h. Tighten the 3/8" bolts to a torque of 43 7 N m (32 5 lb.ft.). If the studs for the exhaust manifold were removed, install new studs, and tighten them to a torque of 25 4 N m (18 3 lb.ft.).4. Make an adjustment to the valves to have a clearance of 0.38 mm (.015 in.) for intake and 0.76 mm (.030 in.) for exhaust. Tighten the locknuts for the valve adjustment screws to a torque of 28 4 N m (21 3 lb.ft.).5. Install the valve cover bases and the inner fuel lines. See Install Rocker Shaft Assemblies And Push Rods.6. Install the valve covers. See Install Valve

Have questions with 105012-0931?





Group cross 105012-0931 ZEXEL

9 432 612 225 
NP-DL140U529AN2R 
 
NOZZLE
9 432 612 226 
NP-DL135U5310NP18 
 
NOZZLE
9 432 612 227 
H4523002300 
 
NOZZLE

Daihatsu 

9 432 611 848 
NP-DL145UE509N3 
W312730700ZA 
NOZZLE
9 432 611 848 
NP-DL145UE509N3 
E326270310Z 
NOZZLE
105012-0931  
9 432 612 228 
NP-DL145UE509N3 
 
NOZZLE

Daihatsu 

9 432 611 847 
NP-DL140UC659N1 
E406200400ZZ 
NOZZLE
9 432 611 871 
NP-DL140U4810AN3 
E286270190ZZ 
NOZZLE
9 432 611 859 
NP-DL140U4810AN3 
E286270190ZA 
NOZZLE
9 432 611 860 
NP-DL145UE559N1 
E326270320AZ 
NOZZLE
9 432 612 229 
NP-DL145UE559N1 
 
NOZZLE
9 432 612 230 
NP-DL140U4510NP5 
 
NOZZLE
9 432 612 231 
NP-DL120UE4210N1 
 
NOZZLE
9 432 612 232 
NP-DL120UE4410N1 
 
NOZZLE
Back to top