Information injector
BOSCH
9 443 613 810
9443613810
ZEXEL
106134-3710
1061343710
NISSAN
166007Y000
166007y000
Rating:
Compare Prices: .
As an associate, we earn commssions on qualifying purchases through the links below
6PCS Fuel Injector 16600-7Y00A 166007Y00A 16600-7Y000 0280158005 Compatible With Compatible With Quest Compatible With Altima
ECAHDVEIR 1. Optimize combustion: improve combustion conditions and prolong engine life. || 2. Wide adaptation: it is suitable for a variety of engines and has good versatility. || 3.Easy maintenance: convenient disassembly and cleaning, and low maintenance cost. || 4. Efficient atomization: Atomize fuel, fully mix, improve power and reduce fuel consumption. || 5.Precise injection: accurately control the injection quantity and improve the fuel utilization rate.
ECAHDVEIR 1. Optimize combustion: improve combustion conditions and prolong engine life. || 2. Wide adaptation: it is suitable for a variety of engines and has good versatility. || 3.Easy maintenance: convenient disassembly and cleaning, and low maintenance cost. || 4. Efficient atomization: Atomize fuel, fully mix, improve power and reduce fuel consumption. || 5.Precise injection: accurately control the injection quantity and improve the fuel utilization rate.
Pack of 6pcs Fuel Injectors 16600-7Y000 0280158005 For Nissan 2003-2009 Altima Maxima Murano Quest 3.5L 4 Holes
GZWANJIN FUNCTION-The vehicle will lose power on the cylinder, not run smoothly or have misfires and will likely have poor gas mileage if your fuel injectors are damaged. Compared to the carbureted engine, the fuel injector helps the automobile industry achieve better transient throttle response and better efficiency. || Compatible with INFINITI EX35 2008-2012 Compatible with INFINITI FX35 2009-2012 Compatible with Nissan Altima 3.5L 2003-2009 Compatible with Nissan Maxima 3.5L 2003-2009 Compatible with Nissan Quest 3.5L 2004-2009 Compatible with Nissan Murano 3.5L 2003-2004 || Manufacturer Part Number 16600-7Y000 842-12297 0280158005 166007Y000 16600 7Y000 16600-7Y00A FJ469 MP4184 155-0370 800-1476N 8001476N 63851 || PREMIUM QUALITY-Long life-span matters, our injector is crafted from composite material to prevent corrosion within the fuel control body leading to an extended service life. High temperature viton o-rings enable prolonged sealing of injector under extreme heat conditions. || SERVICE GURANTEE- Package include: 6PCSx Fuel Injectors. If it fails on your vehicle, feel free to contact us any time.
GZWANJIN FUNCTION-The vehicle will lose power on the cylinder, not run smoothly or have misfires and will likely have poor gas mileage if your fuel injectors are damaged. Compared to the carbureted engine, the fuel injector helps the automobile industry achieve better transient throttle response and better efficiency. || Compatible with INFINITI EX35 2008-2012 Compatible with INFINITI FX35 2009-2012 Compatible with Nissan Altima 3.5L 2003-2009 Compatible with Nissan Maxima 3.5L 2003-2009 Compatible with Nissan Quest 3.5L 2004-2009 Compatible with Nissan Murano 3.5L 2003-2004 || Manufacturer Part Number 16600-7Y000 842-12297 0280158005 166007Y000 16600 7Y000 16600-7Y00A FJ469 MP4184 155-0370 800-1476N 8001476N 63851 || PREMIUM QUALITY-Long life-span matters, our injector is crafted from composite material to prevent corrosion within the fuel control body leading to an extended service life. High temperature viton o-rings enable prolonged sealing of injector under extreme heat conditions. || SERVICE GURANTEE- Package include: 6PCSx Fuel Injectors. If it fails on your vehicle, feel free to contact us any time.
ACROPIX 0280158005 Fuel Injectors 16600-7Y000 for Nissan Maxima Quest Altima Murano 3.5L 2003-2009 Car Parts
ACROPIX Auto Parts: Fitment: for Nissan Altima 2004-2006, for Nissan Quest 2004-2009, for Nissan Maxima 2004-2008, for Nissan Murano 2003-2004 || Car Components: The Part Number(OE Number): 62378, 0280158005, 16600-7YO00, 16600-7YOOA || Automobile Parts: Fuel injector enables fast start up in cold environments; , and no modification needed. || Car Accessories: Product Included: 1 x Fuel Injector; Material: Metal, Plastic; Pin Number: 2; Orifice Type: 4 Holes Disc. Flow rates at 43.5 psi / 3 bar 28.2 lb per hour 213 G per min.(N-Heptane)296.2 cc per min || Auto Components: Note: This is a non-OEM product, accessory only! Please make sure that the OE number and make/model/year/trim are the same as your OEM before buying!
ACROPIX Auto Parts: Fitment: for Nissan Altima 2004-2006, for Nissan Quest 2004-2009, for Nissan Maxima 2004-2008, for Nissan Murano 2003-2004 || Car Components: The Part Number(OE Number): 62378, 0280158005, 16600-7YO00, 16600-7YOOA || Automobile Parts: Fuel injector enables fast start up in cold environments; , and no modification needed. || Car Accessories: Product Included: 1 x Fuel Injector; Material: Metal, Plastic; Pin Number: 2; Orifice Type: 4 Holes Disc. Flow rates at 43.5 psi / 3 bar 28.2 lb per hour 213 G per min.(N-Heptane)296.2 cc per min || Auto Components: Note: This is a non-OEM product, accessory only! Please make sure that the OE number and make/model/year/trim are the same as your OEM before buying!
You can express buy:
USD 58.86
19-05-2025
19-05-2025
6pcs 16600-7Y000 0280158005 Fuel Injector For Nissan Maxima Altima Quest 3.5L 2003 2004 2005 2006 2007 2008 2009 16600-7Y00A
USD 22.38
14-05-2025
14-05-2025
16600-7Y000 166007Y000 16600-7Y00A 166007Y00A 0280158005 Fuel Injector For Nissan Maxima Altima Quest Murano 3.5L Auto Parts
USD 22.38
14-05-2025
14-05-2025
New 16600-7Y000 166007Y000 16600-7Y00A 166007Y00A 0280158005 Fuel Injector For Nissan Maxima Altima Quest Murano 3.5L Auto Parts
Images:
USD 16
[13-May-2025]
USD 40.8
[13-May-2025]
USD 157.69
[13-May-2025]
USD 120.99
[13-May-2025]
Cross reference number
Zexel num
Bosch num
Firm num
Name
106134-3710
9 443 613 810
166007Y000 NISSAN
INJECTOR
C 56KH
C 56KH
Information:
Camshaft
When reconditioning an engine, check the diameter of the camshaft bearing journals and the camshaft lobe height.Camshaft bearing journals have a diameter of 2.5000 .0005 in. (63.500 0.013 mm) and the minimum diameter worn is 2.4970 in. (63.424 mm).To find lobe lift (A) of camshaft, use the following procedure:1. Measure lobe height (B) of one exhaust and one intake lobe.2. Measure base circle (C) of one exhaust and one intake lobe.3. Subtract base circle (C) dimension (STEP 2) from lobe height (B) dimension (STEP 1). The difference is actual lobe lift (A).4. The specified (new) lobe lift (A) is: (a) Exhaust lobe ... .3071 in.(7.800 mm)(b) Intake lobe ... .3077 in.(7.816 mm)5. The maximum permissible difference between actual lobe lift (STEP 3) and specified lobe lift (STEP 4) is .025 in. (0.64 mm).
CAMSHAFT LOBE
A. Lobe lift. B. Lobe height. C. Base circle.With camshaft installed in the cylinder block, check end play. End play with new components should be .007 .003 in. (0.18 0.08 mm). The maximum permissible end play is .020 in. (0.51 mm).Camshaft Followers
Use an 8S2293 Magnet to remove the cam followers.
REMOVING CAM FOLLOWERSCam followers establish a wear pattern with the camshaft lobes. Identify and reinstall the followers removed. Dishing or circular wear pattern is allowed on the cam follower face, providing the wear face keeps a polished appearance. Replace the follower if the wear face is rough or shows signs of scuffing. A new follower can be used with an old camshaft, providing the lobe is in good condition. Put engine oil on the cam followers and the camshaft lobes before installing the cam followers. Use new cam followers with a new camshaft.Camshaft Gears
1. Remove screw (1) and washer (2) from end of camshaft.
REMOVING TIMING ADVANCE RETAINING SCREW
1. Screw. 2. Washer.2. Remove timing advance unit from the camshaft.3. Install puller (A), with spacer (C) over the shaft in the camshaft spacer (B) on spacer (C) as shown and remove the gear from the camshaft.
REMOVING GEAR (Typical Example)
A. 1P2321 Puller. B. 8S5579 Spacer. C. 9S9155 Spacer.To install the gear use the following procedure:1. Heat the gear to a temperature of approximately 400°F (204°C) before installing on the camshaft.
Do not heat the gear with a torch. Do not heat the gear to a temperature of more than 600°F (315°C). Heating the gear with a torch or to a temperature of more than 600°F (315°C) may cause the two drive dowels for the automatic timing advance to loosen and come out of the gear.
2. Align slot in gear hub with the pin in the camshaft. Install the gear on the camshaft with timing mark on gear aligned with timing mark on crankshaft gear. Be sure the gear is completly seated against the shoulder of the camshaft.
Do not drive the gear on the camshaft.
3. Align holes in weights with dowels in gear and install the automatic timing advance.4. Align pin (3) in washer with hole (4) in camshaft and install washer (2).5. Install screw (1) and
When reconditioning an engine, check the diameter of the camshaft bearing journals and the camshaft lobe height.Camshaft bearing journals have a diameter of 2.5000 .0005 in. (63.500 0.013 mm) and the minimum diameter worn is 2.4970 in. (63.424 mm).To find lobe lift (A) of camshaft, use the following procedure:1. Measure lobe height (B) of one exhaust and one intake lobe.2. Measure base circle (C) of one exhaust and one intake lobe.3. Subtract base circle (C) dimension (STEP 2) from lobe height (B) dimension (STEP 1). The difference is actual lobe lift (A).4. The specified (new) lobe lift (A) is: (a) Exhaust lobe ... .3071 in.(7.800 mm)(b) Intake lobe ... .3077 in.(7.816 mm)5. The maximum permissible difference between actual lobe lift (STEP 3) and specified lobe lift (STEP 4) is .025 in. (0.64 mm).
CAMSHAFT LOBE
A. Lobe lift. B. Lobe height. C. Base circle.With camshaft installed in the cylinder block, check end play. End play with new components should be .007 .003 in. (0.18 0.08 mm). The maximum permissible end play is .020 in. (0.51 mm).Camshaft Followers
Use an 8S2293 Magnet to remove the cam followers.
REMOVING CAM FOLLOWERSCam followers establish a wear pattern with the camshaft lobes. Identify and reinstall the followers removed. Dishing or circular wear pattern is allowed on the cam follower face, providing the wear face keeps a polished appearance. Replace the follower if the wear face is rough or shows signs of scuffing. A new follower can be used with an old camshaft, providing the lobe is in good condition. Put engine oil on the cam followers and the camshaft lobes before installing the cam followers. Use new cam followers with a new camshaft.Camshaft Gears
1. Remove screw (1) and washer (2) from end of camshaft.
REMOVING TIMING ADVANCE RETAINING SCREW
1. Screw. 2. Washer.2. Remove timing advance unit from the camshaft.3. Install puller (A), with spacer (C) over the shaft in the camshaft spacer (B) on spacer (C) as shown and remove the gear from the camshaft.
REMOVING GEAR (Typical Example)
A. 1P2321 Puller. B. 8S5579 Spacer. C. 9S9155 Spacer.To install the gear use the following procedure:1. Heat the gear to a temperature of approximately 400°F (204°C) before installing on the camshaft.
Do not heat the gear with a torch. Do not heat the gear to a temperature of more than 600°F (315°C). Heating the gear with a torch or to a temperature of more than 600°F (315°C) may cause the two drive dowels for the automatic timing advance to loosen and come out of the gear.
2. Align slot in gear hub with the pin in the camshaft. Install the gear on the camshaft with timing mark on gear aligned with timing mark on crankshaft gear. Be sure the gear is completly seated against the shoulder of the camshaft.
Do not drive the gear on the camshaft.
3. Align holes in weights with dowels in gear and install the automatic timing advance.4. Align pin (3) in washer with hole (4) in camshaft and install washer (2).5. Install screw (1) and
Have questions with 106134-3710?
Group cross 106134-3710 ZEXEL
Nissan
106134-3710
9 443 613 810
166007Y000
INJECTOR