Fuel injectors
  1. Home
  2. injection
  3. #1093411012

109341-1012 ZEXEL 9 461 629 331 BOSCH INJECTION-PUMP ASSEMBLY 9461629331 1093411012 8973038241


 

Information injection-pump assembly

BOSCH 9 461 629 331 9461629331
ZEXEL 109341-1012 1093411012
ISUZU 8973038241 8973038241
109341-1012 INJECTION-PUMP ASSEMBLY
Rating:
16
Buy INJECTION-PUMP ASSEMBLY 109341-1012 zexel genuine, new aftermarket engine parts with delivery

Components :

0. INJECTION-PUMP ASSEMBLY 109341-1012
1. _
2. FUEL INJECTION PUMP 109241-1003
3. NUMBER PLATE
4. _
5. CAPSULE
6. ADJUSTING DEVICE
7. NOZZLE AND HOLDER ASSY 105118-8212
8. Nozzle and Holder
9. Open Pre:MPa(Kqf/cm2) 19.5{199}/33.8{345}
10. NOZZLE-HOLDER 105048-2270
11. NOZZLE 105017-3090

Scheme ###:

PUMP HOUSING
1. [1] 149002-0020 PUMP HOUSING
3. [1] 149351-0201 PACKING RING
7. [1] 149050-0220 SUPPLY PUMP
9. [1] 149055-0000 SUPPORT RING
10. [4] 149330-2000 TORX SCREW
12. [1] 149100-1120 DRIVE SHAFT
17/1. [1] 149110-0000 SHIM 1460125040
17/1B. [1] 149110-0100 SHIM 1460125041
17/1C. [1] 149110-0200 SHIM
17/1D. [1] 149110-0300 SHIM 1460125043
17/1E. [1] 149110-0400 SHIM 1460125044
17/1F. [1] 149110-0500 SHIM 1460125045
17/1G. [1] 149110-0600 SHIM 1460125046
17/1H. [1] 149110-0700 SHIM 1460125047
17/1I. [1] 149110-0800 SHIM 1460125048
17/1J. [1] 149110-0900 SHIM 1460125049
17/1K. [1] 149110-1000 SHIM 1460125050
17B/1. [1] 149110-1200 SHIM
17B/1B. [1] 149110-1300 SHIM
17B/1C. [1] 149110-1400 SHIM
17B/1D. [1] 149110-1500 SHIM
17B/1E. [1] 149110-1600 SHIM
17B/1F. [1] 149110-1700 SHIM
17B/1G. [1] 149110-1800 SHIM
17B/1H. [1] 149110-1900 SHIM
17B/1I. [1] 149110-2000 SHIM
17B/1J. [1] 149110-2100 SHIM
17B/1K. [1] 149110-2200 SHIM
19. [1] 149111-0000 DRIVER DISC
20. [1] 149120-0820 CAM RING
21. [2] 149112-0200 ROLLER SHOE
22. [2] 149113-0000 ROLLER
23. [1] 149111-0100 PLATE
25. [1] 149114-0000 BEARING PLATE
30. [1] 149350-1500 O-RING
31. [1] 149151-0700 TIMING DEVICE PISTON
32. [1] 149160-0100 (CONTROL SPOOL)
33. [1] 149161-0100 PISTON RING
34. [1] 149162-0000 COILED SPRING
35. [1] 149170-0022 HYDRAULIC STOPPER
36. [1] 149350-1600 O-RING
37. [1] 149180-0101 CLOSING COVER
38. [2] 149330-1800 TORX BOLT
39. [1] 149350-1700 SEAL RING
41. [1] 149163-0100 PLATE
42. [1] 149164-0000 COILED SPRING
49. [4] 149330-1900 TORX BOLT
50. [1] 149201-0521 HYDRAULIC HEAD
51. [3] 149350-2000 O-RING
54. [4] 149313-2700 GASKET
58. [4] 149300-0023 PRESSURE-CONTROL VALVE
59. [1] 479763-6520 MAGNET
61. [3] 149330-2300 TORX BOLT
62. [1] 149436-0000 PLATE
63. [1] 149350-1900 O-RING
67. [1] 149404-0220 PSG
104. [2] 149330-2400 HEX-SOCKET-HEAD CAP SCREW
105. [2] 149443-0200 GASKET
107. [1] 149403-0220 SENSOR
109. [3] 149330-1600 TORX BOLT
111. [2] 149330-0501 TORX SCREW
123. [5] 149330-1700 TORX BOLT
127. [1] 149350-2800 SEAL RING
133. [1] 149350-2900 O-RING
134. [1] 149350-3000 O-RING
135. [1] 149060-0020 CONTROL VALVE
206. [1] 149330-1200 UNION NUT
207. [1] 149412-0000 PLAIN WASHER
213. [2] 149330-0400 TORX SCREW
243. [1] 149330-2400 HEX-SOCKET-HEAD CAP SCREW
244. [1] 149443-0200 GASKET
270. [1] 149411-2500 COUPLING PLATE
271/1. [1] 149411-0200 SHIM
271/1B. [1] 149411-0300 SHIM
271/1C. [1] 149411-0400 SHIM
271/1D. [1] 149411-0500 SHIM
271/1E. [1] 149411-0600 SHIM
271/1F. [1] 149411-0700 SHIM
271/1G. [1] 149411-0800 SHIM
271/1H. [1] 149411-0900 SHIM
271/1I. [1] 149411-1000 SHIM
271/1J. [1] 149411-1100 SHIM
271/1K. [1] 149411-1200 SHIM
271B. [1] 149411-2700 SHIM
392. [1] 149350-3100 O-RING
393. [1] 149419-0100 BLEEDER SCREW
394. [1] 149420-0000 INTERMEDIATE PLATE
394B. [1] 149420-0001 INTERMEDIATE PLATE
400. [1] 149460-1300 CABLE CRAMP
424. [1] 149402-0120 SOLENOID-OPERATED VA
424. [1] 149402-0120 SOLENOID-OPERATED VA
424B. [1] 149402-0220 SOLENOID-OPERATED VA
425. [2] 149330-2200 TORX BOLT
471. [1] 149410-0000 COVER
480. [1] 149350-3200 SEAL RING
902. [1] 149433-0021 OUTLET PIPE ASSY
902/1. [1] 149070-0021 OVER FLOW VALVE
902/2. [1] 149430-0120 INLET UNION
902/3. [2] 149350-2700 FLAT SEAL RING
903. [1] 149428-0021 INLET PIPE
903/1. [1] 149071-0120 EYE BOLT
903/2. [1] 149425-0920 INLET UNION
903/3. [2] 149350-2600 FLAT SEAL RING
911. [4] 149460-0600 CAP
921. [1] 149465-0220 BRACKET
922. [1] 149470-0200 TOOTHED GEAR
923. [1] 149350-1400 O-RING
926. [4] 149442-0100 BLEEDER SCREW
927. [4] 149413-0100 UNION NUT

Include in #2:

109341-1012 as INJECTION-PUMP ASSEMBLY

Cross reference number

Zexel num
Bosch num
Firm num
Name
109341-1012 
109341-1013 
9 461 629 331 
8973038241  ISUZU
INJECTION-PUMP ASSEMBLY
4JH1 587 * K 13CJ VP44 VP44




Information:


Before any service work is done on the fuel system, the outer surface of the injection pump housing must be clean.
1. Remove the plug from location (1). Install tool (A) in the hole with the large diameter end without the taper down. Move the governor control to the "ON" position until the rack stops against tool (A). The racks are now in center (zero) position.2. Disconnect lines (2) from the fuel injection pumps. Remove the washers. Put caps on all fuel openings. 3. Remove bushings (3) with tooling (B). 4. Install tooling (C). Hold the fuel racks in the center (zero) position and carefully remove the fuel injection pump.
When injection pumps, spacers and lifters are removed from the injection pump housing, keep the parts of each pump together so they can be installed back in their original location.
5. Remove spacers (4) from the fuel injection pump housing.
Be careful when the injection pumps are disassembled. Do not cause damage to the surface on the plunger. The plunger and barrel for each pump are made as a set. Do not put the plunger of one pump in the barrel of another pump. If one part has wear, install a complete new pump assembly. Be careful when the plunger is put into the bore of the barrel.
Do not remove gear segment (15) from plunger (10).
6. Remove plunger (10), washer (14) and spring (9) from barrel (8).7. Remove ring (12) from barrel (8) and bonnet (11).8. Remove spring (6), collar (7) and check valve assembly (13) from bonnet (11). Do not disassemble check valve assembly (13).9. Keep seal (5) with the bonnet for use at assembly.Install Fuel Injection Pumps
Make sure the fuel racks are in the center (ZERO) position before the fuel injection pumps are installed.1. Put diesel fuel on all parts to be assembled. 2. Put spring (2), collar (3) and check valve assembly (9) in position in the bonnet.
Do not slide barrel (4) against the check valve assembly when it is assembled. Scratches on the check valve can cause it to leak.
3. Put the bonnet assembly (7) and barrel (4) in position and install ring (8).4. Install spring (5), washer (10) and plunger assembly (6). 5. Put spacer (12) in position in the pump housing bore. Make sure the correct spacer is with each pump. The lobe on the cam must be at its lowest position for easy installation of the fuel injection pumps.6. Hold the fuel racks in the center (ZERO) position when the fuel pumps are installed. Put the space in gear segment (11) in alignment with the groove in barrel (4). 7. Put the injection pump straight down into the housing bore so the space in the gear segment is in alignment with pin (13) and the groove in the barrel is in alignment with dowel (14). Use tool (B) to install the pump. 8. Install seal (1) and bushing (15) in the pump housing bore. If the pump is in the correct position, bushing (15) will

Have questions with 109341-1012?





Group cross 109341-1012 ZEXEL

109341-1010  
 
 
INJECTION-PUMP ASSEMBLY

Isuzu 

109341-1011  

109341-1015 
 
 
INJECTION-PUMP ASSEMBLY
4JH1 587
109341-1012  

109341-1013 
9 461 629 331 
8973038241 
INJECTION-PUMP ASSEMBLY
4JH1 587
109341-1013  

109341-1014 
F 01G 29X 063 
8973038242 
INJECTION-PUMP ASSEMBLY
4JH1 587
109341-1014  

109341-1015 
9 461 628 612 
8973038243 
INJECTION-PUMP ASSEMBLY
4JH1 587
109341-1015  
0 470 504 031 
8973038244 
INJECTION-PUMP ASSEMBLY
4JH1 587
Back to top