108922-3001 ZEXEL 9 400 619 823 BOSCH INJECTION-PUMP ASSEMBLY 9400619823 1089223001 220008891a

Information Cross number Calibration Data Calibration Data Ex

Information injection-pump assembly

BOSCH 9 400 619 823 9400619823

ZEXEL 108922-3001 1089223001

HINO 220008891A 220008891a

Price: query

Buy now
Add to cart Go to cart

Rating:

Buy INJECTION-PUMP ASSEMBLY 108922-3001 zexel genuine, new aftermarket engine parts with delivery

Service parts 108922-3001 INJECTION-PUMP ASSEMBLY:

1. _

2. FUEL INJECTION PUMP 108092-0051

3. GOVERNOR 105923-1441

4. SUPPLY PUMP 105237-4550

5. AUTOM. ADVANCE MECHANIS

6. COUPLING PLATE 105664-2240

7. COUPLING PLATE 156638-9620

8. _ 159600-2720

9. _

10. NOZZLE AND HOLDER ASSY 105101-7802

11. Nozzle and Holder 236002750A

12. Open Pre:MPa(Kqf/cm2) 14.7(150)/21.6(220)

13. NOZZLE-HOLDER 105030-3591

14. NOZZLE

15. NOZZLE SET 105019-0550

Include in #1:

108922-3001 as INJECTION-PUMP ASSEMBLY

Cross reference number

BOSCH 9 400 619 823 9400619823

ZEXEL 108922-3001 1089223001

HINO 220008891A 220008891a

Zexel num

Bosch num

Firm num

Name

108922-3001
108922-3002

9 400 619 823

220008891A HINO

INJECTION-PUMP ASSEMBLY
V-4 * K 14CL TICS

Calibration Data:

Adjustment conditions

Test oil
1404 Test oil ISO4113 or {SAEJ967d}

Test oil temperature degC 40 40 45

Nozzle and nozzle holder 105780-8250

Bosch type code 1 688 901 101

Nozzle 105780-0120

Bosch type code 1 688 901 990

Nozzle holder 105780-2190

Opening pressure MPa 20.7

Opening pressure kgf/cm2 211

Injection pipe
Outer diameter - inner diameter - length (mm) mm 8-3-600

Overflow valve 134424-4120

Overflow valve opening pressure kPa 255 221 289

Overflow valve opening pressure kgf/cm2 2.6 2.25 2.95

Tester oil delivery pressure kPa 255 255 255

Tester oil delivery pressure kgf/cm2 2.6 2.6 2.6

PS/ACT control unit part no. 407980-2 24*

Digi switch no. 52

Direction of rotation (viewed from drive side)
Right R

Injection timing adjustment

Direction of rotation (viewed from drive side)
Right R

Injection order 1-10-9-4 -3-6-5-8 -7-2

Pre-stroke mm 7.2 7.17 7.23

Beginning of injection position
Governor side NO.1

Difference between angles 1
Cal 1-10 deg. 27 26.75 27.25

Difference between angles 2
Cal 1-9 deg. 72 71.75 72.25

Difference between angles 3
Cal 1-4 deg. 99 98.75 99.25

Difference between angles 4
Cal 1-3 deg. 144 143.75 144.25

Difference between angles 5
Cal 1-6 deg. 171 170.75 171.25

Difference between angles 6
Cal 1-5 deg. 216 215.75 216.25

Difference between angles 7
Cal 1-8 deg. 243 242.75 243.25

Difference between angles 8
Cal 1-7 deg. 288 287.75 288.25

Difference between angles 9
Cyl.1-2 deg. 315 314.75 315.25

Injection quantity adjustment

Adjusting point -

Rack position 13.5

Pump speed r/min 700 700 700

Average injection quantity mm3/st. 126.5 123.5 129.5

Max. variation between cylinders % 0 -4 4

Basic *

Fixing the rack *

PS407980-224* V 2.2+-0.0 1

PS407980-224* mm 4.8+-0.0 5

Standard for adjustment of the maximum variation between cylinders *

Injection quantity adjustment_02

Adjusting point Z

Rack position 8.5+-0.5

Pump speed r/min 360 360 360

Average injection quantity mm3/st. 18 15 21

Max. variation between cylinders % 0 -10 10

Fixing the rack *

PS407980-224* V V1+0.05+ -0.01

PS407980-224* mm 7.1+-0.0 3

Standard for adjustment of the maximum variation between cylinders *

Remarks
Refer to items regarding the pre-stroke actuator

Injection quantity adjustment_03

Adjusting point A

Rack position R1(13.5)

Pump speed r/min 700 700 700

Average injection quantity mm3/st. 126.5 124.5 128.5

Basic *

Fixing the lever *

PS407980-224* V 2.2+-0.0 1

PS407980-224* mm 4.8+-0.0 5

Injection quantity adjustment_04

Adjusting point B

Rack position R1+0.6

Pump speed r/min 1100 1100 1100

Average injection quantity mm3/st. 114 108 120

Fixing the lever *

PS407980-224* V 2.2+-0.0 1

PS407980-224* mm 4.8+-0.0 5

0000001601

Pre-stroke mm 7.2 7.17 7.23

Remarks
When the timing sleeve is pushed up

_02

Connector angle deg. 8.5 8 9

Remarks
When the eccentric pin is tightened

_03

Supply voltage V 24 23.5 24.5

Ambient temperature degC 23 18 28

Pre-stroke mm 3.2 3.15 3.25

Output voltage V 2.95 2.94 2.96

Adjustment *

_04

Supply voltage V 24 23.5 24.5

Ambient temperature degC 23 18 28

Pre-stroke mm 7.2 7.17 7.23

Output voltage V 1.2 1 1.4

Confirmation *

Remarks
Output voltage V1

_05

Supply voltage V 24 23.5 24.5

Ambient temperature degC 23 18 28

Output voltage V 3.05 3.05

Confirmation of operating range *

Test data Ex:

Governor adjustment

N:Pump speed R:Rack position (mm) (1)Torque cam stamping: T1 (2)Tolerance for racks not indicated: +-0.05mm. (3)Set stop lever before governor adjustment. [When setting stop lever after governor adjustment, confirm that point I (Ra) can be obtained at full setting.] (4)Stop lever's normal position setting: equivalent to RA (5)Damper spring setting
----------
T1=AD23 Ra=(R1+1)mm RA=18mm
----------

Speed control lever angle

F:Full speed I:Idle (1)Use the hole at R = aa (2)Stopper bolt set position 'H'
----------
aa=47mm
----------
a=20deg+-5deg b=34deg+-3deg

Stop lever angle

N:Pump normal S:Stop the pump. (1)Use the pin at R = aa (2)Set the stopper bolt so that speed = bb and rack position = cc. (Confirm non-injection.) (3)Set the stopper bolt so that rack position = dd.
----------
aa=40mm bb=0r/min cc=4+-0.3mm dd=18mm
----------
a=10deg+-5deg b=30deg+-5deg

0000001301

(1)Pump vertical direction (2)Coupling's key groove position at No 1 cylinder's beginning of injection (3)Pre-stroke: aa (4)-
----------
aa=7.2+-0.03mm
----------
a=(80deg)

0000001901

A:Sealing position B:Pre-stroke actuator 1. When installing the pre-stroke actuator on the pump, first tighten the installation bolts loosely, then move the actuator fully counterclockwise (viewed from the drive side). Temporary tightening torque: 1 - 1.5 N.m (0.1 - 0.15 kgf.m) 2. Move the actuator in the clockwise direction when viewed from the drive side, and adjust so that it becomes the adjustment point of the adjustment value. Then tighten it. Tightening torque: 7^9 N.m (0.7^0.9 kgf.m) 3. After prestroke actuator installation adjustment, simultaneously stamp both the actuator side and housing side.
----------

----------

0000002201 RACK SENSOR

(VR) measurement voltage (I) Part number of the control unit (G) Apply red paint. (H): End surface of the pump 1. Rack limit adjustment (1)Mount the joint (B). (2)Select the shim (D) so that the rack limit's rack position is obtained at that time. (3)Install the rod (E) to the block (C). The distance between the pump end face and the rod (E) at rack limit must be L. 2. Rack sensor adjustment (-0020) (1)Screw in the bobbin (A) until it contacts the joint (B). (2)Fix the speed control lever at the full side. (3)Set at speed N. (4)Adjust the depth that the bobbin (A) is screwed in so that the control unit's rack sensor output voltage is VR+-0.01 (V), then tighten the nut (F). (If equipped with a boost compensator, perform with boost pressure applied.) (5)Adjust the bobbin (A) so that the rack sensor's output voltage is VR+-0.01. (6)Apply G at two places. Connecting part between the joint (B) and the nut (F) Connecting part between the joint (B) and the end surface of the pump (H)
----------
L=38-0.2mm N=860r/min Ra=R1(13.5)+0.85mm
----------

Information:

1. Remove the retaining ring (1) and pin (2). 2. Remove the seat (3), bolt (4), washers (5), and spring (6).3. Remove the sleeve and bearing assembly from the cylinder and weight assembly. 4. Remove the retaining ring (7) from sleeve (8).5. Remove the bearing (9) and races (10) from sleeve (8). 6. Remove the valve (11) from piston (12).7. Remove the retaining ring (13) from the cylinder and weight assembly.8. Remove the weight assembly (14).9. Remove piston (12) and sleeve (15) from the cylinder (16).10. Remove the O-ring seal from sleeve (15). 11. Remove the speed limiter plug (17), spring (18), and plunger (19) from the governor housing.12. Remove the high idle screw (21) and low idle screw (20). 13. Remove the bolt and lock that holds the shaft (22) to lever assembly (23).14. Remove the shaft (22) and lever assembly (23) from governor housing.15. Remove the seal and bearings from governor housing. 16. Remove the two bolts (25) and lock. Remove the lever (24) and shaft (26) from idle screw housing.17. Remove the two seals and bearing from idle screw housing.Assemble Governor
1. Install the O-ring seal (3) on sleeve (4).2. Install piston (2) and sleeve (4) in the cylinder (1). 3. Put the weight assembly (6) in position on cylinder (1), and install retaining ring (5). 4. Install valve (8) in piston (2).5. Install the bearing and races in sleeve. Install the retaining ring. Install the sleeve and bearing assembly (7) on valve (8). 6. Put the bolt (10), washers (11), and spring (12) in position in seat (9). 7. Put the holes in seat (9), sleeve and bearing assembly (7), and valve (8) in alignment, and install the pin (13). Install the retaining ring (14). 8. Use tool setup (A) to install the inner seal in idle screw housing with the spring side of seal toward tool setup (A). Use tool setup (A) to install the outer seal in housing with lip of seal toward inside of housing. Put clean oil on the bearing and lip of seals.9. Put the shaft and lever in position in the idle screw housing, and install the bolts and lock. 10. Install the two bearings in governor housing. Use tool setup (A) to install the seal in housing with lip of seal toward inside of the governor housing. Put clean oil on the bearings and lip of seal. 11. Put the shaft (15) and lever assembly (17) in position in governor housing, and install the bolt (16) and lock. Install the high and low idle screws in housing. Install the speed limiter plunger, spring, and plug in housing.end by: a) connection of governor to fuel injection pump housing