108822-7260 ZEXEL 9 400 619 377 BOSCH INJECTION-PUMP ASSEMBLY 9400619377 1088227260 me352417


 

Information injection-pump assembly

BOSCH 9 400 619 377 9400619377
ZEXEL 108822-7260 1088227260
MITSUBISHI ME352417 me352417
108822-7260 INJECTION-PUMP ASSEMBLY
Rating:
23
Buy INJECTION-PUMP ASSEMBLY 108822-7260 zexel genuine, new aftermarket engine parts with delivery

Service parts 108822-7260 INJECTION-PUMP ASSEMBLY:

1. _
2. FUEL INJECTION PUMP 108082-3700
3. GOVERNOR 105960-0450
4. SUPPLY PUMP 105237-0290
5. AUTOM. ADVANCE MECHANIS
6. COUPLING PLATE 105664-0990
7. COUPLING PLATE
10. NOZZLE AND HOLDER ASSY 105110-7920
11. Nozzle and Holder ME072662
12. Open Pre:MPa(Kqf/cm2) 17.7{180}/24.5{250}
13. NOZZLE-HOLDER 105041-4290
14. NOZZLE
15. NOZZLE SET 105019-2410

Include in #1:

108822-7260 as INJECTION-PUMP ASSEMBLY

Cross reference number

Zexel num
Bosch num
Firm num
Name
108822-7260 
108822-7261 
9 400 619 377 
ME352417  MITSUBISHI
INJECTION-PUMP ASSEMBLY
8M21 * K 14CQ TICS HD-TI8F TICS




Information:

Tachometer Error...To check, connect a tachometer of known accuracy to the engine. Run the engine and make a comparison of the readings of the vehicle and test tachometers. If vehicle tachometer is defective, make repairs as necessary or install a new tachometer.Engine Operated at High Altitude...Less oxygen at higher altitudes causes the engine horsepower to go down approximately three percent for each 1000 ft. above sea level. *Brakes Do Not Completely Release... Check the brakes by feeling all the brake drums. If the brakes do not completely release, the brake drum for that wheel will be hotter than the brake drums for the other wheels. With the truck jacked up the wheels must rotate freely when turned by hand.Vehicle Operated in Too High a Gear... If the operator does not shift the truck correctly or operates the truck in a "lug" condition (using the truck in too high a gear for engine rpm to go up as accelerator pedal is pushed farther down, or using the truck in a gear where engine rpm goes down with accelerator pedal at maximum travel), poor vehicle performance is the result. For best engine performance do not lug the engine more than 600 rpm below its full load speed.Extra Engine Driven Equipment...Air compressors, hydraulic pumps, generators, and other engine driven equipment that has damage, or that was not installed correctly, or that is not in correct adjustment, can take more horsepower to drive than expected. If necessary, disconnect the equipment and test the engine.Speedometer Error...A damaged speedometer does not give the correct speed or the correct indication of fuel consumption. An indication of low speed can cause the operator to feel that he has a power problem.Speeds Too High...The need for more horsepower is easy to see as the speed of the vehicle is increased. This is especially true if the front of the vehicle has a large surface area. Your authorized dealer can give you the horsepower needs for a vehicle, and the horsepower necessary for different vehicle designs at different speeds.Overload on Vehicle *High Moving Resistance...Soft ground conditions cause a need for more horsepower. To see if the problem is the engine, test the vehicle on a surface known to be good, or test on a chassis dynamometer.High Wind Resistance...The horsepower needs for a truck can be divided into two parts. Part of the horsepower is used to move the vehicle and part is used to get through wind resistance. The horsepower necessary to get through the wind resistance will increase as the vehicle is used at higher speeds. Vehicles with a large front area have a higher wind resistance and take more horsepower than those with a small front area. Some types of trucks, for example those used for the transportation of automobiles and/or boats have high wind resistance even if the front area is small. Moving against the wind has the same effect on wind resistance as does higher vehicle speed.Power Loss in Drive Gears...It is possible for

Have questions with 108822-7260?





Group cross 108822-7260 ZEXEL

9 400 611 975 
 
INJECTION-PUMP ASSEMBLY
8M21
9 400 612 094 
 
INJECTION-PUMP ASSEMBLY
9 400 612 396 
 
INJECTION-PUMP ASSEMBLY
9 400 612 685 
 
INJECTION-PUMP ASSEMBLY

Mitsubishi 

9 400 619 374 
ME165430 
INJECTION-PUMP ASSEMBLY
8M21
 
ME355314 
INJECTION-PUMP ASSEMBLY
8M21
F 019 Z10 299 
ME355585 
INJECTION-PUMP ASSEMBLY
8M21
9 400 612 767 
 
INJECTION-PUMP ASSEMBLY

Mitsubishi 

F 019 Z20 381 
ME351539 
INJECTION-PUMP ASSEMBLY
8M21
 
 
INJECTION-PUMP ASSEMBLY
8M21
 
 
INJECTION-PUMP ASSEMBLY
 
 
INJECTION-PUMP ASSEMBLY
9 400 619 375 
 
INJECTION-PUMP ASSEMBLY

Mitsubishi 

F 019 Z20 382 
ME165200 
INJECTION-PUMP ASSEMBLY
8M21
9 400 613 026 
ME351921 
INJECTION-PUMP ASSEMBLY
8M21
9 400 619 631 
ME354919 
INJECTION-PUMP ASSEMBLY
8M21
F 019 Z20 383 
ME355584 
INJECTION-PUMP ASSEMBLY
8M21
9 400 612 966 
ME351917 
INJECTION-PUMP ASSEMBLY
8M21
F 019 Z20 384 
ME354920 
INJECTION-PUMP ASSEMBLY
8M21
9 400 619 376 
ME351918 
INJECTION-PUMP ASSEMBLY
8M21
F 019 Z20 385 
ME354921 
INJECTION-PUMP ASSEMBLY
8M21
108822-7260  

108822-7261 
9 400 619 377 
ME352417 
INJECTION-PUMP ASSEMBLY
8M21
9 400 619 632 
ME354917 
INJECTION-PUMP ASSEMBLY
8M21
9 400 619 378 
ME353380 
INJECTION-PUMP ASSEMBLY
8M21
9 400 619 633 
ME354918 
INJECTION-PUMP ASSEMBLY
8M21
F 01G 09U 0HE 
 
INJECTION-PUMP ASSEMBLY

Mitsubishi 

9 400 619 379 
ME354037 
INJECTION-PUMP ASSEMBLY
8M21
9 400 619 435 
 
INJECTION-PUMP ASSEMBLY

Mitsubishi 

9 400 619 380 
ME354038 
INJECTION-PUMP ASSEMBLY
8M21
Back to top