108822-2860 ZEXEL F 019 Z20 509 BOSCH INJECTION-PUMP ASSEMBLY f019z20509 1088222860 me163705

Information Cross number Calibration Data Calibration Data Ex

Information injection-pump assembly

BOSCH F 019 Z20 509 f019z20509

ZEXEL 108822-2860 1088222860

MITSUBISHI ME163705 me163705

Price: query

Buy now
Add to cart Go to cart

Rating:

Buy INJECTION-PUMP ASSEMBLY 108822-2860 zexel genuine, new aftermarket engine parts with delivery

Service parts 108822-2860 INJECTION-PUMP ASSEMBLY:

1. _

2. FUEL INJECTION PUMP 108082-3341

3. GOVERNOR 105923-3880

4. SUPPLY PUMP 105237-4800

5. AUTOM. ADVANCE MECHANIS

6. COUPLING PLATE 105664-0990

7. COUPLING PLATE

8. _ 159600-5020

9. _ 156641-0520

10. NOZZLE AND HOLDER ASSY 105110-7391

11. Nozzle and Holder ME161933

12. Open Pre:MPa(Kqf/cm2) 15.7{160}/24.5{250}

13. NOZZLE-HOLDER 105041-4101

14. NOZZLE

15. NOZZLE SET 105019-0380

Include in #1:

108822-2860 as INJECTION-PUMP ASSEMBLY

Cross reference number

BOSCH F 019 Z20 509 f019z20509

ZEXEL 108822-2860 1088222860

MITSUBISHI ME163705 me163705

Zexel num

Bosch num

Firm num

Name

108822-2860
108822-7280

F 019 Z20 509

ME163705 MITSUBISHI

INJECTION-PUMP ASSEMBLY
8M21 * K 14CK TICS HD-TI8M TICS

Calibration Data:

Adjustment conditions

Test oil
1404 Test oil ISO4113 or {SAEJ967d}

Test oil temperature degC 40 40 45

Nozzle and nozzle holder 105780-8250

Bosch type code 1 688 901 101

Nozzle 105780-0120

Bosch type code 1 688 901 990

Nozzle holder 105780-2190

Opening pressure MPa 20.7

Opening pressure kgf/cm2 211

Injection pipe
Outer diameter - inner diameter - length (mm) mm 8-3-600

Overflow valve 131425-0220

Overflow valve opening pressure kPa 157 123 191

Overflow valve opening pressure kgf/cm2 1.6 1.25 1.95

Tester oil delivery pressure kPa 255 255 255

Tester oil delivery pressure kgf/cm2 2.6 2.6 2.6

PS/ACT control unit part no. 407980-2 24*

Digi switch no. 42

Direction of rotation (viewed from drive side)
Right R

Injection timing adjustment

Direction of rotation (viewed from drive side)
Right R

Injection order 1-2-7-3- 4-5-6-8

Pre-stroke mm 8.5 8.47 8.53

Beginning of injection position
Governor side NO.1

Difference between angles 1
Cyl.1-2 deg. 45 44.75 45.25

Difference between angles 2
Cal 1-7 deg. 90 89.75 90.25

Difference between angles 3
Cal 1-3 deg. 135 134.75 135.25

Difference between angles 4
Cal 1-4 deg. 180 179.75 180.25

Difference between angles 5
Cal 1-5 deg. 225 224.75 225.25

Difference between angles 6
Cal 1-6 deg. 270 269.75 270.25

Difference between angles 7
Cal 1-8 deg. 315 314.75 315.25

Injection quantity adjustment

Adjusting point -

Rack position 14.3

Pump speed r/min 700 700 700

Average injection quantity mm3/st. 148 146.4 149.6

Max. variation between cylinders % 0 -3 3

Basic *

Fixing the rack *

PS407980-224* V 2.45+-0. 01

PS407980-224* mm 6.1+-0.0 5

Standard for adjustment of the maximum variation between cylinders *

Injection quantity adjustment_02

Adjusting point Z

Rack position 9+-0.5

Pump speed r/min 355 355 355

Average injection quantity mm3/st. 20.5 18.5 22.5

Max. variation between cylinders % 0 -15 15

Fixing the rack *

PS407980-224* V V1+0.05+ -0.01

PS407980-224* mm 8.4+-0.0 3

Standard for adjustment of the maximum variation between cylinders *

Remarks
Refer to items regarding the pre-stroke actuator

Injection quantity adjustment_03

Adjusting point A

Rack position R1(14.3)

Pump speed r/min 700 700 700

Average injection quantity mm3/st. 148 147 149

Basic *

Fixing the lever *

PS407980-224* V 2.45+-0. 01

PS407980-224* mm 6.1+-0.0 5

Injection quantity adjustment_04

Adjusting point B

Rack position R1+1.5

Pump speed r/min 1100 1100 1100

Average injection quantity mm3/st. 146 142 150

Fixing the lever *

PS407980-224* V 2.45+-0. 01

PS407980-224* mm 6.1+-0.0 5

0000001601

Pre-stroke mm 8.5 8.47 8.53

Remarks
When the timing sleeve is pushed up

_02

Connector angle deg. 8.5 8 9

Remarks
When the eccentric pin is tightened

_03

Supply voltage V 24 23.5 24.5

Ambient temperature degC 23 18 28

Pre-stroke mm 6.1 6.05 6.15

Output voltage V 2.45 2.44 2.46

Adjustment *

_04

Supply voltage V 24 23.5 24.5

Ambient temperature degC 23 18 28

Pre-stroke mm 8.5 8.47 8.53

Output voltage V 1.2 1 1.4

Confirmation *

Remarks
Output voltage V1

_05

Supply voltage V 24 23.5 24.5

Ambient temperature degC 23 18 28

Pre-stroke mm 5.5

Output voltage V 3 2.98 3

Confirmation *

_06

Supply voltage V 24 23.5 24.5

Ambient temperature degC 23 18 28

Output voltage V 3.05 3.05

Confirmation of operating range *

Test data Ex:

Governor adjustment

N:Pump speed R:Rack position (mm) (1)Torque cam stamping: T1 (2)Tolerance for racks not indicated: +-0.05mm. (3)Damper spring setting
----------
T1=AC23
----------

Speed control lever angle

F:Full speed I:Idle (1)Use the hole at R = aa (2)Stopper bolt set position 'H' (3)Pump speed = bb at temporary setting (4)Viewed from feed pump side.
----------
aa=45mm bb=1000r/min
----------
a=3deg+-5deg b=31deg+-3deg c=(22deg)

Stop lever angle

N:Pump normal S:Stop the pump. (1)Use the hole at R = aa (2)Set the stopper bolt so that speed = bb and rack position = cc. (Confirm non-injection.) (3)Normal engine position (equivalent to R = dd).
----------
aa=45mm bb=1100r/min cc=4+-0.3mm dd=18mm
----------
a=(31deg)+-5deg b=25.5deg+-5deg c=41deg+-5deg

0000001301

(1)Pump vertical direction (2)Coupling's key groove position at No 1 cylinder's beginning of injection (3)At the No 1 cylinder's beginning of injection position, stamp an aligning mark on the damper to align with the pointer's groove. (4)Damper (5)Pointer (6)B.T.D.C.: aa (7)Pre-stroke: bb
----------
aa=6deg bb=8.5+-0.03mm
----------
a=(45deg) b=(44deg)

0000001901

A:Sealing position B:Pre-stroke actuator 1. When installing the pre-stroke actuator on the pump, first tighten the installation bolts loosely, then move the actuator fully counterclockwise (viewed from the drive side). Temporary tightening torque: 1 - 1.5 N.m (0.1 - 0.15 kgf.m) 2. Move the actuator in the clockwise direction when viewed from the drive side, and adjust so that it becomes the adjustment point of the adjustment value. Then tighten it. Tightening torque: 7^9 N.m (0.7^0.9 kgf.m) 3. After prestroke actuator installation adjustment, simultaneously stamp both the actuator side and housing side.
----------

----------

0000002201 RACK SENSOR

(VR) measurement voltage (I) Part number of the control unit (G) Apply red paint. (H): End surface of the pump 1. Rack sensor adjustment (-0620) (1)Fix the speed control lever at the full position (2)Set the speed to N1 r/min. (If the boost compensator is provided, apply boost pressure.) (3)Adjust the bobbin (A) so that the rack sensor's output voltage is VR+-0.01. (4)At that time, rack position must be Ra. (5)Apply G at two places. Connecting part between the joint (B) and the nut (F) Connecting part between the joint (B) and the end surface of the pump (H)
----------
N1=1100r/min Ra=R1(14.3)+1.5mm
----------

0000002301 MICRO SWITCH

Adjustment of the micro-switch Adjust the bolt to obtain the following lever position when the micro-switch is ON. (1)Speed N1 (2)Rack position Ra
----------
N1=325r/min Ra=8.9+-0.1mm
----------

Information:

ACTION REQUIRED
Refer to the attached Rework Procedure.
SERVICE CLAIM ALLOWANCES
Product smu/age whichever comes first Caterpillar Dealer Suggested Customer Suggested
Parts % Labor Hrs% Parts % Labor Hrs% Parts % Labor Hrs%
0-2000 hrs,
0-24 mo 100.0% 100.0% 0.0% 0.0% 0.0% 0.0%
This is a 2.0-hour job
PARTS DISPOSITION
Handle the parts in accordance with your Warranty Bulletin on warranty parts handling.
Rework Procedure
Use the procedures on the following pages in order to apply the updates to your machine.
- Park the machine on a firm, level surface.
- Fully retract and lower the boom.
- Place the travel select lever in the (N) NEUTRAL position.
- Apply Park Brake.
- Shut the engine off and remove the key from the MAIN switch located inside the engine compartment.
- Properly disconnect the battery.
- Place a Do Not Operate Tag on both the ignition key-switch and the steering wheel, stating that the machine should not be operated.
- Allow the engine area and antifreeze to cool down.
- Remove the cab rear cover.
- Use all applicable safety precautions while working on, around or under any machinery.
1. Locate DEF coolant supply hose (1) and DEF coolant return hose (2) on the engine. Refer to Image1.2.1.
Image1.2.1
2. Trace the routing of DEF coolant supply hose (1) on the engine to DEF coolant control valve (3) located in the middle of the frame. Refer to Image1.2.1 and 1.3.1.
Image1.3.1
3. Trace the routing of DEF coolant return hose (2) from the engine to DEF tank (4) located behind rear of the cab. Refer to Image1.2.1 and 1.4.1.
Image1.4.1
4. If the routing of DEF coolant supply hose (1) and DEF coolant return hose (2) are found to be correct, remount the cab rear cover and place the unit back in service.
5. If the routing of DEF coolant line (1) and DEF coolant return hose (2) are found to be incorrect, please continue the next steps to correct the DEF coolant line installation.
6. Remove all the cable straps that securing the two DEF coolant lines together or to other hoses. Refer to Image1.6.1. Some of the parts have been removed for clarity. Cut the 610cm of 5P-0767 Hose into two pieces: 330cm and 280cm.
Image1.6.1
7. Taking all precautions to minimize and contain any antifreeze spillage, disconnect DEF coolant supply hose (1) from DEF coolant control valve (3) and from the engine side DEF coolant supply port. The hose will not be reused. Retain the hose clamps for reuse. Refer to Image1.2.1 and 1.4.1.
8. Disconnect DEF coolant return hose (2) from DEF coolant tank (4) and from the engine side DEF coolant return port. The hose will not be reused. Retain the hose clamps for reuse. Refer to Image1.2.1 and 1.6.1.
9. Identify the new DEF coolant supply hose. It is the shorter