108622-3776 ZEXEL 9 400 612 244 BOSCH INJECTION-PUMP ASSEMBLY 9400612244 1086223776 220402092a


 

Information injection-pump assembly

BOSCH 9 400 612 244 9400612244
ZEXEL 108622-3776 1086223776
HINO 220402092A 220402092a
108622-3776 INJECTION-PUMP ASSEMBLY
Rating:
45
Buy INJECTION-PUMP ASSEMBLY 108622-3776 zexel genuine, new aftermarket engine parts with delivery

Service parts 108622-3776 INJECTION-PUMP ASSEMBLY:

1. _
2. FUEL INJECTION PUMP 108062-3662
3. GOVERNOR 105952-2570
4. SUPPLY PUMP 105237-4690
5. AUTOM. ADVANCE MECHANIS
6. COUPLING PLATE 105664-0740
7. COUPLING PLATE 156638-7720
9. _
10. NOZZLE AND HOLDER ASSY 105101-8212
11. Nozzle and Holder 23600-3001A
12. Open Pre:MPa(Kqf/cm2) 16.7{170}/27.5{280}
13. NOZZLE-HOLDER 105030-3711
14. NOZZLE
15. NOZZLE SET 105019-0850

Include in #1:

108622-3776 as INJECTION-PUMP ASSEMBLY

Cross reference number

Zexel num
Bosch num
Firm num
Name
108622-3776 
108622-3777 
9 400 612 244 
220402092A  HINO
INJECTION-PUMP ASSEMBLY
P11C-TD * K




Information:

Safety is everyone's business and is basically the use of good common sense. A general guide of safety precautions are given below, but each installation has its own peculiarities which cannot always be predicted and covered by established rules. Past experience and common sense are needed for the necessary safety measures. Attention to safety will help avoid serious accidents. Be alert. Watch for hazards. Use preventive measures. Correct deficiencies immediately.The following safety precautions are a general guide to safe operation:1. To prevent personal injury, install guards over all exposed rotating parts.2. To prevent hearing damage, wear ear protective devices if working inside an enclosed engine room with engine running.3. To prevent head injury, wear safety hat when working in the area of overhead equipment.4. Wear safety glasses and shoes as required. 5. Do not wear loose clothing whenever working around engines or machinery.6. Wipe up spilled oil, fuel or coolant.7. Keep batteries in a well ventilated area. Do not smoke around batteries. Hydrogen gas, which is present in the area of the batteries, is highly explosive.8. Provide adequate and safe waste oil disposal.9. Store oily rags in fireproof containers. Don't leave rags on engine.
When using pressure air, wear safety glasses and protective clothing. Maximum air pressure, used for cleaning, must be below 30 PSI (2 kg/cm2).
10. Remove all tools, electrical cords and other loose items from the engine before starting.11. Disconnect and tape the battery ground lead before working on an engine to prevent accidental starting. Be sure an automatic start-stop system cannot operate and start the engine while working on it.12. Do not attempt repairs you do not understand. Follow instructions.13. Stop engine before adjusting or repairing engine or driven equipment.14. Remove radiator cap slowly. Cooling systems can be pressurized and hot fluid will flash to steam as pressure is removed.15. Never start an engine with the governor linkage disconnected.16. Replace or repair broken or damaged equipment. Use proper tools.17. Do not smoke while refueling. Observe NO SMOKING signs.18. Never store flammable liquids near the engine.19. All electrical equipment must be grounded according to local building codes.20. Check all connections periodically for tightness and insulation.21. Insulate all connections and disconnected wires.22. Do not use carbon tetrachloride fire extinguishers. Fumes are toxic and the liquid has a deteriorating effect on insulation. 23. Do not touch the heat sink on the generator regulator when the generator is running. It is electrically "hot".24. Do not work on electrically "hot" equipment.25. Always disconnect the engine starter circuit when working on the generator.26. Hot engine oil can cause burns when drained. Allow the oil to cool below 140°F or provide protection when draining the hot oil.27. Never remove a plug to check pressure with the engine running. Shut down the engine and assure there is no pressure before removing plug.28. When starting an engine after repair, make provisions for shutting off air supply in case there is an overspeed on start up.29. Never look into an open cylinder port and turn over

Have questions with 108622-3776?





Group cross 108622-3776 ZEXEL

 
 
INJECTION-PUMP ASSEMBLY

Hino 

 
220401610A 
INJECTION-PUMP ASSEMBLY
P11C-TD
 
220401611A 
INJECTION-PUMP ASSEMBLY
P11C-TD
9 400 611 733 
220401612A 
INJECTION-PUMP ASSEMBLY
P11C-TD
9 400 611 406 
 
INJECTION-PUMP ASSEMBLY

Hino 

9 400 611 773 
220402091A 
INJECTION-PUMP ASSEMBLY
P11C-TD
108622-3776  

108622-3777 
9 400 612 244 
220402092A 
INJECTION-PUMP ASSEMBLY
P11C-TD
F 01G 09U 0FW 
220402093A 
INJECTION-PUMP ASSEMBLY
P11C-TD
9 400 619 200 
220402094A 
INJECTION-PUMP ASSEMBLY
P11C-TD
Back to top