108622-2370 ZEXEL 9 400 611 920 BOSCH INJECTION-PUMP ASSEMBLY 9400611920 1086222370


 

Information injection-pump assembly

BOSCH 9 400 611 920 9400611920
ZEXEL 108622-2370 1086222370
108622-2370 INJECTION-PUMP ASSEMBLY
Rating:
75
Buy INJECTION-PUMP ASSEMBLY 108622-2370 zexel genuine, new aftermarket engine parts with delivery

Service parts 108622-2370 INJECTION-PUMP ASSEMBLY:

1. _
2. FUEL INJECTION PUMP 108062-3900
3. GOVERNOR 105960-0300
4. SUPPLY PUMP 105237-0240
5. AUTOM. ADVANCE MECHANIS
6. COUPLING PLATE 105664-0990
7. COUPLING PLATE
10. NOZZLE AND HOLDER ASSY 105110-8041
11. Nozzle and Holder ME180464
12. Open Pre:MPa(Kqf/cm2) 17.7{180}/24.5{250}
13. NOZZLE-HOLDER 105041-3200
14. NOZZLE
15. NOZZLE SET 105019-2570

Include in #1:

108622-2370 as INJECTION-PUMP ASSEMBLY

Cross reference number

Zexel num
Bosch num
Firm num
Name
108622-2370 
108622-2371 
9 400 611 920 
   
INJECTION-PUMP ASSEMBLY
* K




Information:

Cautions Regarding Battery* Handle Battery Carefully * Never use flames or allow sparks near the battery. The battery releases flammable hydrogen gas and oxygen gas. These gases can be ignited by flames and cause an explosion.* Do not use the battery when the fluid surface is lower than the minimum level. Using a battery with a low electrolyte level can result in an explosion.* Do not short the battery terminals with a tool or other metal object.* When disconnecting battery cables, always remove the cable from the negative (-) terminal first. When reconnecting cables, attach the cable to the positive (+) terminal first.* Charge the battery in a well-ventilated area, with all filling hole plugs removed.* Make sure the cable clamps are securely installed on the battery terminals. A loose cable clamp can cause sparks that may result in explosion.* Before servicing electrical components or conducting electrical welding, set the battery switch to the [Open/OFF] position or disconnect the cable from the negative (-) battery terminal to cut off the electrical current.* Electrolyte (battery fluid) contains dilute sulfuric acid. Careless handling of the battery can lead to the loss of sight and/or burns. Also, do not swallow electrolyte.* Wear protective goggles and rubber gloves when maintaining and inspecting the battery (when adding water, charging, etc.).* If electrolyte is spilled onto the skin or clothes, immediately wash with lots of clean fresh water and thoroughly clean with soap.* If electrolyte gets into eyes, immediately flush with lots of clean fresh water and seek immediate medical attention.* Should you accidentally swallow electrolyte, gargle with plenty of water, then drink lots of water, and seek immediate medical attention.
Response To Abnormalities* If Engine Overheats, Conduct Heating Operation Before Stopping The Engine If the engine overheats, do not stop the engine immediately. Abruptly stopping an overheated engine may cause the coolant temperature to rise, resulting in seizing of the engine. If the engine overheats, operate the engine at low idling speed (cooling temperature), and stop the engine after the coolant temperature lowers sufficiently.Do not add coolant immediately after stopping the engine. Adding coolant to a hot engine may cause damage to the cylinder heads due to sudden change in temperature. Add coolant after the engine cools to room temperature.* If Engine Stops Due To Abnormality, Exercise Caution When Restarting If the engine stops due to an abnormality, do not restart the engine immediately. If the engine stops with an alarm, check and correct the cause of the problem before restarting. Operating the engine without correcting the problem may result in serious engine problems.* If Oil Pressure Drops, Stop Engine Immediately If the engine oil pressure decreases, stop the engine immediately, and inspect the lubrication system. Operating the engine with low oil pressure may cause seizing of the bearings and other parts.* If Fan Belt Breaks, Stop Engine Immediately If the fan belt breaks, stop the engine immediately. Continued operation of the engine without the fan belt causes coolant to change to steam and

Have questions with 108622-2370?





Group cross 108622-2370 ZEXEL

 
 
INJECTION-PUMP ASSEMBLY
 
 
INJECTION-PUMP ASSEMBLY

Mitsubishi 

9 400 611 965 
ME153102 
INJECTION-PUMP ASSEMBLY
6D24T2
9 400 619 788 
 
INJECTION-PUMP ASSEMBLY
9 400 611 672 
 
INJECTION-PUMP ASSEMBLY
9 400 611 300 
 
INJECTION-PUMP ASSEMBLY
6D24T2
9 400 612 392 
 
INJECTION-PUMP ASSEMBLY

Mitsubishi 

F 019 Z20 358 
ME153130 
INJECTION-PUMP ASSEMBLY
6D24T2
9 400 611 565 
ME121777 
INJECTION-PUMP ASSEMBLY
6D40T1
9 400 611 566 
ME121776 
INJECTION-PUMP ASSEMBLY
6D40T1
9 400 612 883 
ME121772 
INJECTION-PUMP ASSEMBLY
6D40T
 
 
INJECTION-PUMP ASSEMBLY
E86X
9 400 619 152 
 
INJECTION-PUMP ASSEMBLY

Mitsubishi 

F 019 Z20 359 
ME180463 
INJECTION-PUMP ASSEMBLY
6M70
 
 
INJECTION-PUMP ASSEMBLY
 
 
INJECTION-PUMP ASSEMBLY
 
 
INJECTION-PUMP ASSEMBLY
6M70

Mitsubishi 

9 400 619 153 
ME180874 
INJECTION-PUMP ASSEMBLY
6M70
F 019 Z20 360 
ME354916 
INJECTION-PUMP ASSEMBLY
6M70
108622-2370  

108622-2371 
9 400 611 920 
 
INJECTION-PUMP ASSEMBLY

Mitsubishi 

9 400 611 966 
ME181434 
INJECTION-PUMP ASSEMBLY
6M70
F 019 Z20 361 
ME354887 
INJECTION-PUMP ASSEMBLY
6M70
 
 
INJECTION-PUMP ASSEMBLY

Mitsubishi 

F 019 Z20 362 
ME354936 
INJECTION-PUMP ASSEMBLY
6D24
 
ME357251 
INJECTION-PUMP ASSEMBLY
6D24T2
 
 
INJECTION-PUMP ASSEMBLY
F 019 Z20 363 
 
INJECTION-PUMP ASSEMBLY
6D24T2

Mitsubishi 

F 019 Z20 363 
ME355477 
INJECTION-PUMP ASSEMBLY
6D24T2
F 019 Z10 803 
 
INJECTION-PUMP ASSEMBLY
6D24T2

Mitsubishi 

F 019 Z10 803 
ME355477 
INJECTION-PUMP ASSEMBLY
6D24T2
F 01G 09U 1GY 
ME355477 
INJECTION-PUMP ASSEMBLY
6D24T2
Back to top