107492-2140 ZEXEL INJECTION-PUMP ASSEMBLY Calibration Data 1074922140

Information Cross number Calibration Data Calibration Data Ex

Information injection-pump assembly

ZEXEL 107492-2140 1074922140

Price: query

Buy now
Add to cart Go to cart

Rating:

Buy INJECTION-PUMP ASSEMBLY 107492-2140 zexel genuine, new aftermarket engine parts with delivery

Service parts 107492-2140 INJECTION-PUMP ASSEMBLY:

1. _

2. FUEL INJECTION PUMP 107049-3071

3. GOVERNOR 105921-8740

4. SUPPLY PUMP 105237-6360

5. AUTOM. ADVANCE MECHANIS

6. COUPLING PLATE

7. COUPLING PLATE 156638-9320

8. _ 159600-1720

9. _

10. NOZZLE AND HOLDER ASSY 105118-5381

11. Nozzle and Holder ME015202

12. Open Pre:MPa(Kqf/cm2) 21.6{220}

13. NOZZLE-HOLDER 105048-3730

14. NOZZLE 105017-1221

15. NOZZLE SET

Include in #1:

107492-2140 as INJECTION-PUMP ASSEMBLY

Cross reference number

ZEXEL 107492-2140 1074922140

Zexel num

Bosch num

Firm num

Name

107492-2140

INJECTION-PUMP ASSEMBLY
14CF TICS MD-TI4 TICS

Calibration Data:

Adjustment conditions

Test oil
1404 Test oil ISO4113 or {SAEJ967d}

Test oil temperature degC 40 40 45

Nozzle and nozzle holder 105780-8250

Bosch type code 1 688 901 101

Nozzle 105780-0120

Bosch type code 1 688 901 990

Nozzle holder 105780-2190

Opening pressure MPa 20.7

Opening pressure kgf/cm2 211

Injection pipe
Outer diameter - inner diameter - length (mm) mm 8-3-600

Overflow valve 131425-0520

Overflow valve opening pressure kPa 255 221 289

Overflow valve opening pressure kgf/cm2 2.6 2.25 2.95

Tester oil delivery pressure kPa 255 255 255

Tester oil delivery pressure kgf/cm2 2.6 2.6 2.6

PS/ACT control unit part no. 407910-3 03*

Selector switch no. 02

PS/ACT control unit part no. 407980-2 24*

Digi switch no. 01

Direction of rotation (viewed from drive side)
Right R

Injection timing adjustment

Direction of rotation (viewed from drive side)
Right R

Injection order 1-3-4-2

Pre-stroke mm 5.6 5.57 5.63

Beginning of injection position
Drive side NO.1

Difference between angles 1
Cal 1-3 deg. 90 89.75 90.25

Difference between angles 2
Cal 1-4 deg. 180 179.75 180.25

Difference between angles 3
Cyl.1-2 deg. 270 269.75 270.25

Injection quantity adjustment

Adjusting point -

Rack position 12.3

Pump speed r/min 800 800 800

Average injection quantity mm3/st. 110 108.4 111.6

Max. variation between cylinders % 0 -3 3

Basic *

Fixing the rack *

PS407980-224* V 2.25+-0. 01

PS407980-224* mm 3.6+-0.0 5

PS407910-303* V 2.25+-0. 01

PS407910-303* mm 3.6+-0.0 5

Standard for adjustment of the maximum variation between cylinders *

Injection quantity adjustment_02

Adjusting point Z

Rack position 7.4+-0.5

Pump speed r/min 540 540 540

Average injection quantity mm3/st. 16 14.5 17.5

Max. variation between cylinders % 0 -15 15

Fixing the rack *

PS407980-224* V V1+0.05+ -0.01

PS407980-224* mm 5.5+-0.0 3

PS407910-303* V V1+0.05+ -0.01

PS407910-303* mm 5.5+-0.0 3

Standard for adjustment of the maximum variation between cylinders *

Remarks
Refer to items regarding the pre-stroke actuator

Injection quantity adjustment_03

Adjusting point A

Rack position R1(12.3)

Pump speed r/min 800 800 800

Average injection quantity mm3/st. 110 109 111

Fixing the lever *

Boost pressure kPa 43.3 43.3

Boost pressure mmHg 325 325

PS407980-224* V 2.25+-0. 01

PS407980-224* mm 3.6+-0.0 5

PS407910-303* V 2.25+-0. 01

PS407910-303* mm 3.6+-0.0 5

Injection quantity adjustment_04

Adjusting point B

Rack position R1+2.1

Pump speed r/min 1450 1450 1450

Average injection quantity mm3/st. 112.5 108.5 116.5

Fixing the lever *

Boost pressure kPa 43.3 43.3

Boost pressure mmHg 325 325

PS407980-224* V 2.25+-0. 01

PS407980-224* mm 3.6+-0.0 5

PS407910-303* V 2.25+-0. 01

PS407910-303* mm 3.6+-0.0 5

Boost compensator adjustment

Pump speed r/min 500 500 500

Rack position R2-1.4

Boost pressure kPa 20 18.7 21.3

Boost pressure mmHg 150 140 160

Boost compensator adjustment_02

Pump speed r/min 500 500 500

Rack position R2(R1-0. 4)

Boost pressure kPa 30 30 30

Boost pressure mmHg 225 225 225

0000001601

CU407980-224* *

Actuator retarding type *

Supply voltage V 12 11.5 12.5

Ambient temperature degC 23 18 28

Pre-stroke mm 2.5 2.45 2.55

Output voltage V 2.83 2.82 2.84

Adjustment *

_02

CU407980-224* *

Supply voltage V 12 11.5 12.5

Ambient temperature degC 23 18 28

Pre-stroke mm 5.6 5.57 5.63

Output voltage V 1.2 1 1.4

Confirmation *

Remarks
Output voltage V1

_03

CU407980-224* *

Supply voltage V 12 11.5 12.5

Ambient temperature degC 23 18 28

Output voltage V 3.05 3.05

Confirmation of operating range *

_04

CU407910-303* *

Actuator retarding type *

Supply voltage V 12 11.5 12.5

Ambient temperature degC 23 18 28

Pre-stroke mm 2.5 2.45 2.55

Output voltage V 2.83 2.82 2.84

Adjustment *

_05

CU407910-303* *

Supply voltage V 12 11.5 12.5

Ambient temperature degC 23 18 28

Pre-stroke mm 5.6 5.57 5.63

Output voltage V 1.2 1 1.4

Confirmation *

Remarks
Output voltage V1

_06

CU407910-303* *

Supply voltage V 12 11.5 12.5

Ambient temperature degC 23 18 28

Output voltage V 3.05 3.05

Confirmation of operating range *

Test data Ex:

Governor adjustment

N:Pump speed R:Rack position (mm) (1)Torque cam stamping: T1 (2)Tolerance for racks not indicated: +-0.05mm. (3)Boost compensator stroke: BCL
----------
T1=L04 BCL=1.4+-0.1mm
----------

Speed control lever angle

F:Full speed I:Idle (1)Use the hole at R = aa (2)Stopper bolt setting
----------
aa=40mm
----------
a=22deg+-5deg b=(38deg)+-3deg

Stop lever angle

N:Pump normal S:Stop the pump. (1)Use the hole at R = aa (2)Set the stopper screw so that speed = bb and the rack position = cc and confirm non-injection. (3)After setting the stopper bolt, confirm non-injection at speed dd.
----------
aa=40mm bb=1450r/min cc=1-0.5mm dd=400r/min
----------
a=36.5deg+-5deg b=(45deg)+-5deg

0000001301

(1)Pump vertical direction (2)Position of gear mark '3' at No 1 cylinder's beginning of injection (3)B.T.D.C.: aa (4)Pre-stroke: bb
----------
aa=7deg bb=5.6+-0.03mm
----------
a=(130deg)

0000001401

(1)Pointer (2)Injection timing aligning mark (3)Fly weight (4)The actual shape and direction may be different from this illustration. Operation sequence 1. Turn the prestroke actuator OFF. 2. Turn the camshaft as far as the No.1 cylinder's beginning of injection position. 3. Check that the pointer alignment mark of the injection pump and the alignment mark of the flywheel are matching. 4. If they are not matching, erase the alignment mark on the flywheel side, and stamp an alignment mark on the flywheel position that matches with the pointer side alignment mark. 5. Check again that the coupling's key groove position is in the No.1 cylinder's beginning of injection position.
----------

----------

0000001701

A : Stopper pin B: Connector
----------

----------

0000001801

C:Shim
----------

----------

0000001901

A:Sealing position B:Pre-stroke actuator 1. When installing the pre-stroke actuator on the pump, first tighten the installation bolts loosely, then move the actuator fully counterclockwise (viewed from the drive side). Temporary tightening torque: 1 - 1.5 N.m (0.1 - 0.15 kgf.m) 2. Move the actuator in the clockwise direction when viewed from the drive side, and adjust so that it becomes the adjustment point of the adjustment value. Then tighten it. Tightening torque: 7^9 N.m (0.7^0.9 kgf.m) 3. After prestroke actuator installation adjustment, simultaneously stamp both the actuator side and housing side.
----------

----------

0000002201 RACK SENSOR

(VR) measurement voltage (I) Part number of the control unit (G) Apply red paint. (H): End surface of the pump 1. Rack sensor adjustment (-0620) (1)Fix the speed control lever at the full position (2)Set the speed to N1 r/min. (If the boost compensator is provided, apply boost pressure.) (3)Adjust the bobbin (A) so that the rack sensor's output voltage is VR+-0.01. (4)At that time, rack position must be Ra. (5)Apply G at two places. Connecting part between the joint (B) and the nut (F) Connecting part between the joint (B) and the end surface of the pump (H)
----------
N1=1450r/min Ra=R1(12.3)+2.1mm
----------

Information:

REM02-46
Reman
November 2002 REMANUFACTURED FUEL INJECTORS FOR VARIOUS INDUSTRIAL, MACHINE, MARINE AND ON-HIGHWAY TRUCK APPLICATIONS Announcement The Caterpillar Remanufactured Products Group announces the expansion of the remanufactured injector product line to include coverage for various C10, C12, 3176, 3196, 3406E, 3456, C15, C16, and C18 Industrial, Machine, Marine and On-Highway Truck applications. Coverage The addition of these injectors provides dealers with an additional repair option to support various C10, C12, 3176, 3196, 3406E, 3456, C15, C16, and C18 Industrial, Machine, Marine and On-Highway Truck applications where low sulfur fuel is present. Coverage is extensive so please consult your NPR or Reman Cross Reference for exact model coverage. See the matrix on page two for part numbers and cross-reference information. Features And Benefits Features
All critical engineering changes and updates included
Worldwide availability through Caterpillar? parts distribution system
Backed by Cat warranty Benefits
Improved reliability and performance
Customer access regardless of location
Consistent support Core Acceptance Core Acceptance Criteria for Caterpillar Remanufactured injectors is simple, visual, and requires no special tools. Full core credit is issued when the core is complete, fully assembled, and has an acceptable part number. Consult your Core Acceptance Guide for complete details. Warranty Please consult the appropriate warranty statement for your area. Core Management Please refer to the Caterpillar Core Management Information System (CMIS 2) Parts Information application describing all reman part/CAF and related information. Also refer to other CMIS 2 inquiry applications such as Customer Profiles, Inspection Reason Codes, Inspection Line Inquiry, Add Charge Information, Entitlement Activity, Entitlement Inquiry, CCR Inquiry, CCR Entry, Shipment Processing; Process Packaging Grief; and Reporting to properly manage core returns and monitor inspection performance. This information will be available to all dealers worldwide after your CMIS 2 conversion date. In the meantime, please continue to use the current CMIS Entitlement Parts Inquiry Screen describing the list of parts in a Core Acceptability Family (CAF) and related part number detail. For the latest updates of Reman Policies and Core Management (SELD0122), Core Management Systems & Operations Procedures (SELD0040), and Shipping Instructions (SELD0039), go to the Reman website and click on Procedures and Policies (listed under Reman Program Information). If you have any questions regarding core return processing, feel free to call your Corinth Dealer Service Representative toll free at (800) 537-2928 or use our e-mail address -- reman_core_operations. For assistance with technical questions, call the Peoria Reman Customer Satisfaction Hot Line also toll free at (888) 88-REMAN or use our e-mail address--Reman_Help.
PELE0956 CATERPILLAR? ?2002 Caterpillar