106971-5194 ZEXEL F 01G 09U 0CC BOSCH INJECTION-PUMP ASSEMBLY f01g09u0cc 1069715194

Information Cross number Calibration Data Calibration Data Ex

Information injection-pump assembly

BOSCH F 01G 09U 0CC f01g09u0cc

ZEXEL 106971-5194 1069715194

Price: query

Buy now
Add to cart Go to cart

Rating:

Buy INJECTION-PUMP ASSEMBLY 106971-5194 zexel genuine, new aftermarket engine parts with delivery

Cross reference number

BOSCH F 01G 09U 0CC f01g09u0cc

ZEXEL 106971-5194 1069715194

Zexel num

Bosch num

Firm num

Name

106971-5194
106971-5195

F 01G 09U 0CC

INJECTION-PUMP ASSEMBLY
RH10 * K

Calibration Data:

Adjustment conditions

Test oil
1404 Test oil ISO4113 or {SAEJ967d}

Test oil temperature degC 40 40 45

Nozzle and nozzle holder 105780-8250

Bosch type code 1 688 901 101

Nozzle 105780-0120

Bosch type code 1 688 901 990

Nozzle holder 105780-2190

Opening pressure MPa 20.7

Opening pressure kgf/cm2 211

Injection pipe
Outer diameter - inner diameter - length (mm) mm 8-3-600

Overflow valve 131425-0120

Overflow valve opening pressure kPa 157 123 191

Overflow valve opening pressure kgf/cm2 1.6 1.25 1.95

Tester oil delivery pressure kPa 255 255 255

Tester oil delivery pressure kgf/cm2 2.6 2.6 2.6

RED3 control unit part number 407910-3 960

RED3 rack sensor specifications mm 19

Direction of rotation (viewed from drive side)
Right R

Injection timing adjustment

Direction of rotation (viewed from drive side)
Right R

Injection order 10-9-4-3 -6-5-8-7 -2-1

Pre-stroke mm 4.4 4.37 4.43

Beginning of injection position
Governor side NO.1

Difference between angles 1
Cal 10-9 deg. 45 44.75 45.25

Difference between angles 2
Cal 10-4 deg. 72 71.75 72.25

Difference between angles 3
Cal 10-3 deg. 117 116.75 117.25

Difference between angles 4
Cal 10-6 deg. 144 143.75 144.25

Difference between angles 5
Cal 10-5 deg. 189 188.75 189.25

Difference between angles 6
Cal 10-8 deg. 216 215.75 216.25

Difference between angles 7
Cal 10-7 deg. 261 260.75 261.25

Difference between angles 8
Cal 10-2 deg. 288 287.75 288.25

Difference between angles 9
Cal 10-1 deg. 333 332.75 333.25

Injection quantity adjustment

Rack position (13.4)

Vist V 1.84 1.84 1.84

Pump speed r/min 700 700 700

Average injection quantity mm3/st. 128.5 126.5 130.5

Max. variation between cylinders % 0 -4 4

Basic *

Injection quantity adjustment_02

Rack position (8.8)

Vist V 2.5 2.4 2.6

Pump speed r/min 370 370 370

Average injection quantity mm3/st. 16 14 18

Max. variation between cylinders % 0 -10 10

Test data Ex:

Governor adjustment

(1)Adjusting range (2)Step response time (N): Speed of the pump (L): Load (theta) Advance angle (Srd1) Step response time 1 (Srd2) Step response time 2 1. Adjusting conditions for the variable timer (1)Adjust the clearance between the pickup and the protrusion to L.
----------
L=1-0.2(mm) N2=800r/min C2=(9)deg t1=1.7--sec. t2=1.7--sec.
----------
N1=1000++r/min P1=0kPa(0kgf/cm2) P2=392kPa(4kgf/cm2) C1=9+-0.3deg R01=0/4load R02=4/4load

Speed control lever angle

N:Pump normal S:Stop the pump. (1)Rack position = aa (2)Rack position bb
----------
aa=20mm bb=1mm
----------
a=27deg+-5deg b=37deg+-5deg

0000000901

(1)Pump vertical direction (2)Position of the coupling's key groove at the start of injection for the No. 10 cylinder. (3)- (4)-
----------

----------
a=(90deg)

Stop lever angle

(Rs) rack sensor specifications (C/U) control unit part number (V) Rack sensor output voltage (R) Rack position (mm) 1. Confirming governor output characteristics (rack 19 mm, span 6 mm) (1)When the output voltages of the rack sensor are V1 and V2, check that the rack positions R1 and R2 in the table above are satisfied.
----------

----------

Information:

This Program can only be administeredafter a failure occurs. The decision whether to apply the Program is madeby the dealer. When reporting the repair, use "PS50780" as the Part numberand "7755" as the Group Number. Use "96" as the Warranty Claim DescriptionCode and use "Z" as the SIMS Description Code. The information supplied in this serviceletter may not be valid after the termination date of this program. Donot perform the work outlined in this Service Letter after the terminationdate without first contacting your Caterpillar product analyst. This Revised Service Letter replacesthe April 2, 2004 (Revised April 2004) Service Letter. Changes have beenmade to the Affected Product.TERMINATION DATE
April 30, 2006PROBLEM
Failed injector and wiring harness need to bereplaced on certain C-9 Industrial Engines. The C-9 engine can developan injector misfire due to an open connection at the injector to harnessconnector. This misfire can be diagnosed with standard troubleshootingguide procedures.AFFECTED PRODUCT
Model Identification Number
C9 CLJ1-4259
12H 12500001-40AMZ1-496CBK1-353
330C B1K1-178B2L1-203B4N1-187BTM1-189CGZ1-511CYA1-287D3C1-231JAB1-626JCD1-292JNK1-245KDD1-580MCA1-427MKM1-308GAG1-329RBH1-233
330C L CAP1-1257DKY1-2011HAA1-393
D6R II AEM1-100AFM1-115BLE1-199BLT1-186BMK1-121BNL1-99BPM1-101BPP1-97BPS1-102BRJ1-116
D6R II LGP ACJ1-101ADE1-311BNC1-265BPZ1-142
D6R II XL AAX1-465BMJ1-130BMY1-297BRZ1-115CAD1-143FDT1-141
D6R II XW AEP1-223DAE1-129
470 7651-811
475 7671-824
MT765 AMS1-266
TK711 10100001-00191
TK721 10200001-00191
TK722 10300001-00193
TK732 10400185-00190
627G CEX187-296
637G CEH222-255PARTS NEEDED
Qty
Part Number
Description
1 1567106 Wiring Kit
1 1889865 Harness Assembly
1 2359651 Bolt - Socket
1 2360962 Injector GroupACTION REQUIRED
Replace the single failed injector with the new 2360962 Injector and the1889865 Wiring Harness Assembly. Refer to REHS1809 Special Instructionfor use of the 1567106 Wiring Kit.SERVICE CLAIM ALLOWANCES
Product smu/age whichever comes first Caterpillar Dealer Suggested Customer Suggested
Parts Labor Hrs Parts Labor Hrs Parts Labor Hrs
0-5000
0-35 months 100% 2.0 0 0 0 0
This is a 2?hour job.PARTS DISPOSITION
Handle the parts in accordance with your Warranty Bulletin on warrantyparts handling.